Search Results

This paper combines fluid software STAR-CCM+ and finite element software ABAQUS to solve the temperature field of this Gasoline engine exhaust manifold based on loose coupling method. Through the simulation of car parking cooling - full load condition at full speed, we estimate thermal fatigue life of the exhaust manifold with the plastic strain increment as the evaluation parameters. It can guide the direction of optimal design of the exhaust manifold. Here we also revealed how the bolt force affects the manifold elastic and plastic behavior.

Glass lifter is a key part of automobile door system. Guide rail is the carrier of glass lifter, and it bears various load cases when glass lifer works. Mass, stiffness and natural frequencies are the factors that influence the performance of glass lifter. In order to design a lighter and reasonable glass lifter, topology optimization methods are studied in this paper. In a rope-wheel glass lifter, design domain is determined by the mechanical structure and working conditions. Firstly, the single target continuum structure topology optimization mathematic models of guide rail are built in this paper, and analysis of multi-stiffness topology optimization are carried out accordingly in which volume fraction is set as 0.4, 0.5 and 0.6. These models are based on SIMP (Solid Isotropic Material with Penalization) theory.

While the car ownership increasing all over the world, the unutilized thermal energy in automobile exhaust system is gradually being realized and valued by researchers around the world for better driving energy efficiency. For the unexpected urban traffic, the frequent start and stop processes as well as the acceleration and deceleration lead to the temperature fluctuation of the exhaust gas, which means the unstable hot-end temperature of the thermoelectric module generator (TEG). By arranging the heat conduction oil circulation at the hot end, the hot-end temperature’s fluctuation of the TEG can be effectively reduced, at the expense of larger system size and additional energy supply for the circulation. This research improves the TEG hot-end temperature stability by installing solid heat capacity material(SHCM) to the area between the outer wall of the exhaust pipe and the TEG, which has the merits of simple structure, none energy consumption and light weight.

With the help of organic working medium absorbing the solar energy for steam electric power generation, green energy can be provided to automotive accessories so as to improve the vehicle energy efficiency. In the hot summer, the exhausted heat resulting from cars’ directly exposing to the sun can be used to cool and ventilate the passenger compartment. Considering the space occupied by the system in the combination of both practical features for solar heat source--low power and poor stability-- a compact evaporation structure was designed to enhance the solar utilization efficiency. In the research, the heat source of power and temperature variation range was determined by the available solar roof with photo-thermal conversion model. Then started from the ratio of exhausted heat utilization corresponding to evaporator’s characteristic parameter, the performance analysis was made in the different working conditions.

The automobile exhaust energy can be recovered by the thermoelectric module generator(TEG). Owing to the complex urban traffic, the exhaust gas’s temperature fluctuations are resulted, which means the unstable hot-end temperature of the TEG. By installing solid heat capacity material(SHCM) to the area between the outer wall of the exhaust pipe and the TEG, it is possible to appropriately reduce the temperature fluctuation, but there is still a fluctuation of the TEG’s power output. Then by adding voltage filter circuit (VFC) after the TEG, the power output stability can be improved. This research uses SHCM and VFC to improve the stability of the exhaust gas generation. Firstly, the three-dimensional heat transfer model of the exhaust pipe thermoelectric power generation system is established. The heat capacity materials with low thermal resistance and high heat capacity were selected as the research object based on previous research.

Li-ion power battery is the core component of the electric vehicle power system, and the battery temperature will increase because of the electrochemical reaction of the Li-ion battery. The heat accumulates inside of the battery, which can degrade the working performance of the power battery and shorten the battery cycle life. At present, the wind cooling technology is relatively mature. However, it cannot achieve ideal heat dissipation effect under the working conditions of the high-power or high ambient temperature. In this research, the battery thermal management is carried out by the characteristics of the working fluid’s flowing phase change heat transfer. The phase change working fluid is R-1233zd(E) which is a kind of environmentally friendly liquid with nonconductive and nonflammable. It can achieve the purpose of controlling the battery’s temperature using the characteristics of isothermal heat absorption under different gas phase rate of phase change working fluid.

In order to predict the thermal fatigue life of the internal combustion engine exhaust manifold effectively, it was necessary to accurately obtain the unsteady heat transfer process between hot streams and exhaust manifold all the time. This paper began with the establishment of unsteady coupled heat transfer model by using serial coupling method of CFD and FEA numerical simulations, then the bidirectional thermal coupling analysis between fluid and structure was realized, as a result, the difficulty that the transient thermal boundary conditions were applied to the solid boundary was solved. What's more, the specific coupling mode, the physical quantities delivery method on the coupling interface and the surface mesh match were studied. On this basis, the differences between strong coupling method and portioned treatment for solving steady thermal stress numerical analysis were compared, and a more convenient and rapid method for solving static thermal stress was found.

As an auxiliary braking device of heavy-duty vehicle, eddy current retarder can reduce the brake failure due to the high temperature of the main brake. Nevertheless, the eddy current retarder will generate high temperature locally during the working process of it, leading to the decline of the brake power. The study on the heating characteristics of eddy current retarder is advantageous to the layout and parameter design of the liquid cooling channel of the retarder body and prolong the effective time of the auxiliary brake. In this research, a new kind of integrated eddy current retarder has been established. The thermal-magnetic coupling characteristics are studied and the laws of variation in torque output of auxiliary brake affected by the body temperature of retarder are analyzed. The boundary conditions are provided for the construction of the cooling channel. Firstly, the distribution of magnetic field and the characteristics of eddy current are simulated.

In order to ensure driving safety, heavy vehicles are often equipped with hydraulic retarder, which provides sustained, stable braking torque and converts the vehicle kinetic energy into heat taken away by the cooling system when traveling on a long downhill. The conventional hydraulic retarder braking torque is modulated by adjusting the liquid filling rate, which leads to slow response and difficult control. In this paper, a new kind of magnetorheological (MR) fluid hydraulic retarder is designed by replacing the traditional transmission oil with MR fluid and arranging the excitation coils outside the working chamber. The braking torque can be controlled by the fluid viscosity of MR fluid with the variation of magnetic field. Compared with the traditional hydraulic retarder, the system has the advantages of fast response, easy control and high adjustment sensitivity.

The performance of an organic Rankine cycle (ORC) that recovers heat from the exhaust of a heavy-duty diesel engine was simulated. The work was an extension of a prior study that simulated the performance of an experimental ORC system developed and tested at Oak Ridge National laboratory (ORNL). The experimental data were used to set model parameters and validate the results of that simulation. For the current study the model was adapted to consider a 15 liter turbocharged engine versus the original 1.9 liter light-duty automotive turbodiesel studied by ORNL. Exhaust flow rate and temperature data for the heavy-duty engine were obtained from Southwest Research Institute (SwRI) for a range of steady-state engine speeds and loads without EGR. Because of the considerably higher exhaust gas flow rates of the heavy-duty engine, relative to the engine tested by ORNL, a different heat exchanger type was considered in order to keep exhaust pressure drop within practical bounds.

The seal structure and key parameters of wheel bearing were introduced. Research on sealing failure diagnosis, abrasive scratch analysis, residual interference, and abrasion reconstruction was carried out for a typical seal structure. Based on these methods of scientific failure analysis, eight causes of seal failure were summarized systematically, which were important for the guidance of seal design and failure analysis of wheel bearings.

The Organic Rankine Cycle System (ORC) is an effective means to use the solar energy. The system adopts the solar energy on the car roof as the heat source to make the ORC work and drive the thermoelectric air-conditioner. It can improve the entering comfort on the parking condition and the vehicle energy utilization efficiency. In this research, the system comprehensively applied the principle of sunshine concentration, heat collection and photo electricity. Then considering the working condition and performance features of ORC system, the car roof was designed to have a compact structure, through which the efficiency of the solar vehicle system could be improved. Firstly, the research analyzed the heat source temperature and the heat flux impact on the output power of the ORC system. After that, the performance of heat collection was identified according to the given thermoelectric air-condition’s power requirements.

To prevent braking recession, heavy commercial vehicles are often equipped with fluid auxiliary braking devices, such as hydraulic retarder. Hydraulic retarder can convert the vehicle’s kinetic energy to the fluid heat energy, which can enormously alleviate the main brake’s workload. The traditional hydraulic retarder can provide enough braking torque but has a delay during the braking. In this paper, a new type of magnetorheological fluid (MR fluid) hydraulic retarder is introduced by replacing the traditional fluid with magnetorheological fluid because of its linear braking torque and quick response. By changing the magnetic field intensity, it is easier to control the braking torque than the traditional hydraulic retarder. The rise of magnetorheological fluid temperature during the braking period will reduce the hydraulic retarder’s performance.

The thermal management system is essential for the safe and long-term operation of the power battery. The temperature difference between the individual cells exceeds the acceleration of the battery performance, which leads to battery out of use and affects the performance of the vehicle. Compared with the low heat transfer coefficient of the air-cooling system, the complex structure of the liquid-cooling system and the large quality of phase change material system, the heat pipe has high thermal conductivity, strong isothermal performance and light weight, it’s an efficient cooling element that can be used for thermal management. In this study, the flat plate heat pipe(FPHP) is used to manage the temperature of the battery, through experiments, the optimized placement of the flat heat pipe is obtained.

In order to avoid the braking recession on heavy commercial vehicles caused by the long-distance continuous braking of the main brake, the hydraulic retarder is widely used as an important brake auxiliary device in various heavy commercial vehicles to improve the vehicle safety. However, the hydraulic retarder not only has the advantages of large braking torque and good stability, but also has the disadvantages of poor retarding ability at low rotating speed, braking lag and difficulty in accurately controlling the braking torque. This paper introduces a new type of hydraulic retarder. The new retarder replaces the oil in the retarder with magnetorheological fluid and applies a magnetic field in the retarder arrangement space, so that slows down the vehicle by using the rheological properties of the magnetorheological fluid under the magnetic field.

For vehicle thermoelectric generator, heat would be directly transferred into electricity by thermoelectric modules because there was temperature difference between heat exchanger and water tank. The electrical power generation was deeply influenced by temperature difference, temperature uniformity and topological structure of TEG. In previous works, increasing the difference of temperature would significantly enhance the power generation of TEG and inserted fins were always applied to enhance heat transfer in parallel-plate heat exchanger. But fins would result in a large backpressure which was not conductive to efficiency of the engine.In current study, to enhance heat transfer rates and outside surface temperature, cylindrical grooves on the top and bottom surface in heat exchanger was proposed. The cylindrical grooves could increase the heat transfer area and enhance the turbulence intensity, meanwhile there was no inserts in the fluid to block the flow.

Heat generated by friction between the brake discs and the brake pad causes the disc temperature to rise, which affects the braking performance. This flux generated from the contact surface of the vehicle brake disc not only affects the braking performance but also tends to be wasted and pollutes the environment. However, an accurate system is needed to make efficient use of this generated heat flux, which is usually wasted. Thermoelectric generators (TEGs) are solid-state gadgets utilized in the conversion of heat to electricity. Hence, the aim of this study is to convert the heat flux generated at the disc contact surface into electrical energy by employing a thermoelectric generator. In Addition, the energy harvested energy to power the battery, which in turn charges the temperature monitoring systems. Thermoelectric generators were positioned at different geometrical points of the brake discs to achieve optimal efficiency and energy storage possibilities.

In the Formula Student Electric China (FSEC), the body structure is generally divided into two types, truss steel tube body and carbon fiber load-bearing body (monocoque). The monocoque is loved by Formula Student teams around the world because it has a higher stiffness and lighter weight than the truss steel tube body. With the widespread application of monocoque, it also brings more problems. Due to the use of the monocoque, the connection between each component and the body was changed from the welding of the original truss steel pipe frame to a bolted connection. However, the bolted connection will provide a large preload force to the monocoque, resulting in the monocoque easily crushed in the local, so it is necessary to pre-bury an enhanced part in the monocoque to ensure the connection strength, that is, the embedded part. At present, aluminum plug-ins after topological hollow processing are being used.

The hydraulic retarder, an important auxiliary brake, has been widely used in heavy vehicles. Under the non-braking working condition, the air resistance torque in the working chamber, which is formed by the rotor of hydraulic retarder's stirring the air, causes pumping loss. This research designs a new type of hydraulic retarder, whose helium is charged into working chamber through closed loop gas system under non-braking working condition, can reduce the parasitic power loss of transmission system. First, under non-braking working condition, the resistance characteristics are analyzed on the base of hydraulic retarder pumping model; then, considering some parameters, such as the volume of chambers and the initial gas pressure, the working chamber gas charge model is established, and the transient gas charge characteristics are also analyzed under non-braking working condition.

In the racing world, speed is everything, and the Formula Student cars are no different. As one of the key means to improve the speed of the car, lightweight plays an important role in the racing world. The weight reduction of unsprung metal parts can not only improve the driving speed, but also effectively optimize the dynamic of the car, so the lightweight design of unsprung parts has attracted much attention. In the traditional Formula Student racing car, the hub and spoke are two independent parts, they are fixed by four hub bolts or a central locking nut, the material of these fasteners is usually steel, so it brings a lot of weight burden. In order to achieve unsprung lightweight, a new type of wheel part design of Formula Student racing car is proposed in this paper. The hub and spoke are designed as integrated aluminum alloy parts, effectively eliminating the mass of hub bolts or central locking nuts.