Search Results

Measurement using a three-dimensional anemometric-tester was made for the gas flow inside the cylinder of a two-stroke engine while the shape of the transfer port was modified. The relationship between port shape and engine performance was investigated for various factors that characterize the flow in cylinder. In this paper, we focused mainly on two engine running conditions: the maximum output at 11750 rpm and the output at 10000 rpm. As a result, we found that the maximum output is most related to the tangential inclination angles of the main transfer port, and the inner vent radius of the main transfer duct.

Mixture formation is one of the most important factors for the combustion in the spark ignition engine with port fuel injection. The relation between combustion and mixture quality, however, is not quantitatively well established. In this study, the connection of combustion and mixture formation was explored with various measurement techniques. Borescopes were used in order to investigate the flame propagation in the combustion chamber and behavior of spray and fuel film on the wall in the intake port. For the purpose of investigation on the effect of mixture formation, various port fuel injection systems and parameters were tested and compared: direction, timing, and size of droplet. An SI engine for small vehicle was used under condition of 4 000 rpm. The investigation by images obtained has shown that inhomogeneity of mixture causes low combustion stability, especially due to direct introduction of fuel droplets into the combustion chamber.

The demands on internal combustion engines for low emissions and fuel consumption are increasing year by year. On the other hand, engines to be used in motorcycles need to provide high output and quick response to meet user desire. In order to realize low fuel consumption while keeping high performance, it is necessary to properly understand cyclic variations during combustion as well as the influence of the injection system on fuel control during transient periods. The current paper reports on the results of a study in the influence of port fuel injection on combustion stability in a small displacement motorcycle engine, using both a series of experiments and CFD. The parameters of the injection systems under study are: (1) injection targeted area, (2) injection timing, and (3) fuel droplet size. The results of the current study show that injection aimed at the upstream wall yielded the best combustion stability.

A monolithic type aluminum (Al) cylinder made of hypereutectic Aluminum-Silicon alloy has been widely used for motorcycle applications. It has a lightweight structure and a superior cooling ability owing to its material property and surface finishing. Usually the cylinder bore surface of the monolithic type Al cylinder is finished by an etching process or a honing process in order to expose silicon (Si) particles from aluminum (Al) matrix for the improvement of the tribological properties. The morphology of the cylinder bore surface including the exposure of Si particles is supposed to make an important effect on its tribological properties, especially on the anti-scuffing property. In this research, the anti-scuffing property of three kinds of cylinder bore finishing, an etched surface, a Si exposure honed surface and a conventional plateau honed surface is evaluated with using a reciprocated type wear tester. The experimental results are analyzed by using Weibull analysis.

All the primary inertia forces and/or moments generated by engines having three cylinders or less are not normally in balance by themselves and thus may be a great source of vibration for the frame supporting the engine. If the mass distribution of the crankwebs is selected in a proper manner, it is possible to determine arbitrarily the directions and the length ratio of principal axes of ellipses, which are obtained as Lissajous diagrams of inertia force and moment. This method can be effectively applied to reduce vibration in the frames. In this paper the appropriate inertia force and moment ellipse equations are developed and the analysis is outlined for optimizing the engine balance. Also the fundamental properties of the linear vibration systems excited by the elliptical forces as well as some experimental examples of elliptical excitation are detailed.

Gasoline fueled Homogeneous Charge Compression Ignition (HCCI) combustion with internal exhaust gas re-circulation using Negative Valve Overlap (NOL) was investigated by means of calculation and experiment in order to apply this technology to practical use with sufficient operating range and with acceptable emission and fuel consumption. In this paper we discuss the basic characteristics of NOL-HCCI with emphasis on the influence of intake valve timing on load range, residual gas fraction and induction air flow rate. Emission and fuel consumption under various operation conditions are also discussed. A water-cooled 250cc single cylinder engine with a direct injection system was used for this study. Three sets of valve timing were selected to investigate the effect of intake valve opening duration. Experimental results demonstrated that an engine speed of approximately 2000rpm yields an NMEP (Net Mean Effective Pressure) range from 200kPa to 400kPa.

The Bonded Valve Seat System is the latest technology to realize drastic reduction in valve temperature in SI engines characterized by the good thermal conductivity of extremely thin valve seats bonded directly on the aluminum cylinder head. A unique and highly rationalized resistance bonding technique was developed to maintain adequate bonding strength and positioning precision in a short bonding period of around one second. Engineering data on optimization of bonding-section geometry, valve seat material and the surface treatment and bonding parameters were presented and discussed regarding the mechanism. The geometry of the bonding section of the cylinder head was optimized by FEM analysis so that the aluminum material should deform to embed the valve seat ring with the action of expelling the surface contamination and the oxide film. The bonding facility was modified so that the electrode axis should move flexibly according to distortion of the cylinder head during bonding.

This paper covers certain aspects of the 2-stroke cycle, high-speed, high-output racing engine developed by Yamaha. Based upon design concepts and data from the development of the general racing engine, as well as the development of Grand Prix racing engines, this material is especially concerned with intake, scavenging, and exhaust systems. In addition, data on cooling and lubrication systems are presented.

The two-stroke engines were in the main stream of the outboard motors, but they have been replaced with the four-stroke counterparts reflecting the environmental protection movement in recent years. However, the replacement with four-stroke engines involves increased number of components and additional displacement, and the outboard motors tend to be larger and heavier. This represents an issue, since the maneuverability of the boat is degraded due to the inappropriate weight distribution on the boat. Yamaha outboard motors F300B and VF250A, of which the production started in the year 2009, are equipped with four-stroke engines, and yet achieved the light weight equivalent to their two-stroke counterparts. The production volume of these models reached 20,000 units.

We compared motoring friction loss, output performance at WOT (wide open throttle) and specific fuel consumption of big-end bearings on engines having identical specifications between the case of using plain bearings and rolling bearings to investigate the effect of the lubricating oil supply rate on these parameters in an attempt to improve output through reduction of friction loss for big-end bearings of small, high-output motorcycle engines. Testing was performed using a 125 cc, 4-cycle, single cylinder engine at high engine speeds mainly above 10,000 rpm.

A periodic impulsive sound at idle is occasionally described as ‘disagreeable’ in two-stroke engines. The relation between combustion conditions, piston vibrations, and the disagreeable sound is analyzed to clarify the phenomena. Some means to alleviate disagreeable sound are then proposed through stabilized combustion, high rigidity sound transfer systems, and refined skirt profiles. Experimental results are shown for the effects on main three factors evaluating disagreeable sound-loudness, impulsiveness, and frequency characteristics. In addition, piston behavior is measured, and the relation between piston motion and disagreeable sound is discussed in this paper.

This study deals with reduced-order modeling of intake air dynamics in single-cylinder four-stroke naturally-aspirated spark-ignited engines without surge tanks. It provides an approximate calculation method for embedded micro computers to estimate intake manifold pressures in real time. The calculation method is also applicable to multi-cylinder engines with individual throttle bodies since the engines can be equated with parallelization of the single-cylinder engines. In this paper, we illustrate the intake air dynamics, describe a method to estimate the intake manifold pressures, and show experimental results of the method.

A centralized control system utilizing optical communication has been developed. Except for the ignition system, almost all electrical functions are under the centralized control. As a method of simplifying wire harness, the time division multiplex communication system using optical communication is adopted. As a result, this new system has made it possible to reduce the number of wires in wire harness from 174 to 123, that of connectors from 60 to 50, and the weight of the wire harness from 1,600 g to 1,350 g. In addition, this system has allowed to reduce the control units (relays) from 11 to 2 (excluding the ignition system).

MotoGP is the pinnacle of motorcycle racing, with the world's top riders racing 800cc prototype machines at leading venues around the world. The riders compete against each other to win the title and show their superiority. The manufacturers have improved the engines every year to gain high power with low-fuel consumption. The percentage of the duration in fully open throttle is less than 20% of the race, but the partial throttle is used as much as 80%. Moreover, when the rider accelerates the machine, the front tire is easy to be lifted from the ground. In the middle of corner, the rider cannot open the throttle fully because of the tire slip. Therefore, it is the most important factor to appropriately control a throttle in the partial area. The Drive-By-Wire (DBW) system is one of the solutions for the force control. The vehicle simulation in the engine dyno test helped efficiently to evaluate the DBW.

In product development of motorcycles, application of CAN at the initial design stage is more necessary than ever to ensure the reliability of the product and also to shorten the lead time of product development. Finite element method (FEM) plays a crucial role in this respect. In the application of FEM to the development of small vehicles, such as motorcycles, analysis must he carried out in a short period and at a low cost. However, FEM requires complex operations and therefore, designers have been unable to use this method satisfactorily. In order to improve these matters, we have developed a system, called STAGE-FEM, which enable the engineers to make FEM models of components of motorcycle and to evaluate the analysis results easily.

The purpose of this paper is to investigate the effect of the piston shape and weight on the friction losses. The motoring test was conducted on pistons with various shapes, rigidities, and weights at 3000-16000 rpm. The test results suggested that the piston friction loss would be abruptly increased mainly because of the increase in the skirt friction caused by the change of the piston attitude. Then, the piston behavioral simulation was conducted using a two-dimensional rigid model in consideration of the skirt rigidity, which proved the above suggestion. This paper consists of the paper presented at 1990 JSAE Autumn Convention and the results of the investigation we conducted based on the calculation of piston behavioral simulation.

THE MULTI-VALVE FOUR STROKE CYCLE engine design trend is Coward increased engine power and higher fuel efficiency. While a four-valve system is the most common direction, problems occur when the valve area is widened by increasing the cylinder bore for a higher engine output. The layout of four larger valves causes the combustion chamber shape to flatten and the combustion time period to increase. In pursuit of the optimum multi-valve engine we have studied four, five, six and seven-valve per cylinder design. Performance targets and design constraints led us toward the successful five-valve engine technology. This technology develops high engine torque and efficient combustion over a wide range of engine speeds.

By orthogonalizing the primary inertia moment vector produced by an engine with many engine vectors, a new engine mounting method called “the orthogonal engine mount system” was designed. This paper explains its theoretical background. In addition, a motorcycle with a two-cylinder engine incorporating this system was analyzed by means of modal analysis and building block approach techniques to determine the effectiveness of the orthogonal engine mount system.

With the hope of efficient and sophisticated motorcycle engine development, an engine test bed that can simulate vehicle running conditions using an ultra-low inertia motor and high response load control system was constructed, and was applied to the development of engines. By combining an exhaust gas analyzer, an exhaust gas constant volume sampler (CVS), and a data processing system, mass emissions could be measured in various test cycles. This system's advantages for data repeatability and test efficiency compared with a chassis test using a vehicle were confirmed. An acceleration test was conducted to assess running performance, and good agreement with actual driving values was confirmed. In addition, by measuring and evaluating engine response to throttle manipulation, it was possible to evaluate driveability on the test bed. These test findings indicate that this test bed can simulate vehicle driving tests with the engine only and will be a useful tool in engine development.

A mathematical model to estimate the shape of a brake hose has been developed. A few papers applying Finite Element Methods (FEM) to this problem have been reported. However, the solutions require a large amounts of computational time even if a super computer is used. A brake hose is made of a flexible material such as rubber, and exhibits large scale deformation when it is mounted on a chassis. Element node displacements are chosen as the independent variables for FEM, so the method becomes a successive iteration of hose shape modifications based on displacements of the nodes. The developed model is approached from the standpoint of mechanical dynamics. A brake hose is divided into small beam elements and particles. The particles are driven by element forces and move around in three-dimensional space.