Search Results

Measurement using a three-dimensional anemometric-tester was made for the gas flow inside the cylinder of a two-stroke engine while the shape of the transfer port was modified. The relationship between port shape and engine performance was investigated for various factors that characterize the flow in cylinder. In this paper, we focused mainly on two engine running conditions: the maximum output at 11750 rpm and the output at 10000 rpm. As a result, we found that the maximum output is most related to the tangential inclination angles of the main transfer port, and the inner vent radius of the main transfer duct.

The demands on internal combustion engines for low emissions and fuel consumption are increasing year by year. On the other hand, engines to be used in motorcycles need to provide high output and quick response to meet user desire. In order to realize low fuel consumption while keeping high performance, it is necessary to properly understand cyclic variations during combustion as well as the influence of the injection system on fuel control during transient periods. The current paper reports on the results of a study in the influence of port fuel injection on combustion stability in a small displacement motorcycle engine, using both a series of experiments and CFD. The parameters of the injection systems under study are: (1) injection targeted area, (2) injection timing, and (3) fuel droplet size. The results of the current study show that injection aimed at the upstream wall yielded the best combustion stability.

A monolithic type aluminum (Al) cylinder made of hypereutectic Aluminum-Silicon alloy has been widely used for motorcycle applications. It has a lightweight structure and a superior cooling ability owing to its material property and surface finishing. Usually the cylinder bore surface of the monolithic type Al cylinder is finished by an etching process or a honing process in order to expose silicon (Si) particles from aluminum (Al) matrix for the improvement of the tribological properties. The morphology of the cylinder bore surface including the exposure of Si particles is supposed to make an important effect on its tribological properties, especially on the anti-scuffing property. In this research, the anti-scuffing property of three kinds of cylinder bore finishing, an etched surface, a Si exposure honed surface and a conventional plateau honed surface is evaluated with using a reciprocated type wear tester. The experimental results are analyzed by using Weibull analysis.

All the primary inertia forces and/or moments generated by engines having three cylinders or less are not normally in balance by themselves and thus may be a great source of vibration for the frame supporting the engine. If the mass distribution of the crankwebs is selected in a proper manner, it is possible to determine arbitrarily the directions and the length ratio of principal axes of ellipses, which are obtained as Lissajous diagrams of inertia force and moment. This method can be effectively applied to reduce vibration in the frames. In this paper the appropriate inertia force and moment ellipse equations are developed and the analysis is outlined for optimizing the engine balance. Also the fundamental properties of the linear vibration systems excited by the elliptical forces as well as some experimental examples of elliptical excitation are detailed.

Gasoline fueled Homogeneous Charge Compression Ignition (HCCI) combustion with internal exhaust gas re-circulation using Negative Valve Overlap (NOL) was investigated by means of calculation and experiment in order to apply this technology to practical use with sufficient operating range and with acceptable emission and fuel consumption. In this paper we discuss the basic characteristics of NOL-HCCI with emphasis on the influence of intake valve timing on load range, residual gas fraction and induction air flow rate. Emission and fuel consumption under various operation conditions are also discussed. A water-cooled 250cc single cylinder engine with a direct injection system was used for this study. Three sets of valve timing were selected to investigate the effect of intake valve opening duration. Experimental results demonstrated that an engine speed of approximately 2000rpm yields an NMEP (Net Mean Effective Pressure) range from 200kPa to 400kPa.

The Bonded Valve Seat System is the latest technology to realize drastic reduction in valve temperature in SI engines characterized by the good thermal conductivity of extremely thin valve seats bonded directly on the aluminum cylinder head. A unique and highly rationalized resistance bonding technique was developed to maintain adequate bonding strength and positioning precision in a short bonding period of around one second. Engineering data on optimization of bonding-section geometry, valve seat material and the surface treatment and bonding parameters were presented and discussed regarding the mechanism. The geometry of the bonding section of the cylinder head was optimized by FEM analysis so that the aluminum material should deform to embed the valve seat ring with the action of expelling the surface contamination and the oxide film. The bonding facility was modified so that the electrode axis should move flexibly according to distortion of the cylinder head during bonding.

This paper describes aspects of YAMAHA 2 cycle, high speed, high output engines. Generally speaking, in order to obtain good results in developing engine performance, high delivery ratios and high thermal and mechanical efficiencies are essential. In addition to these, the most suitable cooling and lubricating systems must be employed. YAMAHA has developed a separate and automatic lubrication system for 2-cycle gasoline engines, which keeps YAMAHA engines well lubricated.

The two-stroke engines were in the main stream of the outboard motors, but they have been replaced with the four-stroke counterparts reflecting the environmental protection movement in recent years. However, the replacement with four-stroke engines involves increased number of components and additional displacement, and the outboard motors tend to be larger and heavier. This represents an issue, since the maneuverability of the boat is degraded due to the inappropriate weight distribution on the boat. Yamaha outboard motors F300B and VF250A, of which the production started in the year 2009, are equipped with four-stroke engines, and yet achieved the light weight equivalent to their two-stroke counterparts. The production volume of these models reached 20,000 units.

We compared motoring friction loss, output performance at WOT (wide open throttle) and specific fuel consumption of big-end bearings on engines having identical specifications between the case of using plain bearings and rolling bearings to investigate the effect of the lubricating oil supply rate on these parameters in an attempt to improve output through reduction of friction loss for big-end bearings of small, high-output motorcycle engines. Testing was performed using a 125 cc, 4-cycle, single cylinder engine at high engine speeds mainly above 10,000 rpm.

MotoGP is the pinnacle of motorcycle racing, with the world's top riders racing 800cc prototype machines at leading venues around the world. The riders compete against each other to win the title and show their superiority. The manufacturers have improved the engines every year to gain high power with low-fuel consumption. The percentage of the duration in fully open throttle is less than 20% of the race, but the partial throttle is used as much as 80%. Moreover, when the rider accelerates the machine, the front tire is easy to be lifted from the ground. In the middle of corner, the rider cannot open the throttle fully because of the tire slip. Therefore, it is the most important factor to appropriately control a throttle in the partial area. The Drive-By-Wire (DBW) system is one of the solutions for the force control. The vehicle simulation in the engine dyno test helped efficiently to evaluate the DBW.

THE MULTI-VALVE FOUR STROKE CYCLE engine design trend is Coward increased engine power and higher fuel efficiency. While a four-valve system is the most common direction, problems occur when the valve area is widened by increasing the cylinder bore for a higher engine output. The layout of four larger valves causes the combustion chamber shape to flatten and the combustion time period to increase. In pursuit of the optimum multi-valve engine we have studied four, five, six and seven-valve per cylinder design. Performance targets and design constraints led us toward the successful five-valve engine technology. This technology develops high engine torque and efficient combustion over a wide range of engine speeds.

In the past, the performance of motorcycle engines has improved quite rapidly through intensive competition in racing and in the marketplace. Motorcycle engines have contributed to the technological progress of internal combustion engines (hereafter abbreviated as ICE). Today's environmental concerns require motorcycle engines to improve fuel economy and exhaust emission pollutants. After examination of potential measures to improve the thermal efficiency of small engines, it was concluded that if engineers of motorcycle engines fail to take on new ideas such as those being developed in cold fusion, it is foreseen that motorcycle engines will be replaced with new power plants as was seen on locomotives in the past.

A high-quality die-casting technology has been developed for lightweight aluminum frame structures that produces high-strength aluminum parts that are also weldable. This new technology has been used in casting frames for motorcycles and snowmobiles and has enabled improved frame designs with far fewer component parts than was possible before. This die-casting technology also results in a significant reduction in energy consumption during the manufacturing process.

With emergence of fuel cells which have much better thermal efficiency than internal combustion engines (later abbreviated as ICE), ICE has to improve its thermal efficiency to the level of 50%. One of the ways to improve the thermal efficiency of ICE is to utilize ultra-lean combustion and several technical papers have been published. But it seems the thermal efficiency has not been improved as the theory predicts. The test data of these technical papers were re-examined and it was concluded that the thermal dissociation of burned gas and NOx formation is the key factor of a discrepancy between the theory and the actual test data. In order to prevent an occurrence of thermal dissociation, emulsified fuels (mixture of carbonaceous fuels with water) was proposed.

A construction of the technology concerning fuel consumption improvement is an important problem not only for the four-wheeled vehicle but also for the motorcycle in recent years when petroleum resources are depleted rapidly. Yamaha originally developed a new fuel injection system (YMJET-FI) and applied the system to a single cylinder, water-cooled and small-displacement engine. In this paper, we would introduce the results of improving the fuel economy with keeping high performance. Improvements were noted in three matters, namely, in the lower load range, 1.Strengthening of in-cylinder flow, 2.Atomization of fuel spray, and 3.Reduction of wall film quantity.

This paper proposes a novel engine starter system composed of a small-power electric motor and a simple mechanical valve train. The system makes it possible to design more efficient starters than conventional systems, and it is especially effective to restart engines equipped with idling stop systems. Recently, several idling stop systems, having intelligent start-up functions and highly-efficient generate capabilities have been proposed for motorcycles. One of challenges of the idling stop systems is the downsizing of electric motors for starting-up. However, there are many limitations to downsize the electric motors in the conventional idling stop systems, since the systems utilize the forward-rotational torque of the electric motors to compress the air-fuel mixture gas in the cylinders. Our studies exceeded the limitations of downsizing the electric motors by mainly using the engine combustion energy instead of the electric energy to go over the first compression top dead center.

In this study, an improvement of fuel consumption by changing the exhaust timing of a two-stroke engine has been made. The study results revealed that a remarkable improvement of fuel economy is possible by controlling the exhaust timing according to the engine speed. The reason for the better fuel economy was clarified through an analysis of exhaust gases, theoretical cycle calculations, and an analysis of combustion pressure. As an example of actual application, the results of tests made on an engine equipped with Yamaha power Valve System (YPVS), which is a variable exhaust timing mechanism using a tabor-shaped valve, will also be discussed.

In recent years, global warming, depletion of fossil fuels, and reducing pollution have become increasingly prominent issues, resulting in demand for environmentally-friendly two-wheeled vehicles capable of reducing CO2 emissions. However, it remains necessary to meet customers’ expectations by providing smaller drivetrains, lighter vehicles, and support for long-distance riding, among other characteristics. In the face of this situation, hybrid electric vehicle (HEV) systems are considered to be the most realistic method for creating environmentally-friendly powertrains and are widely used. This research introduces a hybrid electric two-wheeled vehicle fitted with an electrical variable transmission (EVT) system, a completely new type of electrical transmission that meets the aforementioned needs, achieving enhanced fuel efficiency with a compact drivetrain. The EVT system comprises double rotors installed inside the stator.

Attempts have been made to develop an electronically controlled fuel injection system that is ideal for small motorcycles, cost-efficient, compact, and electric power-saving while maintaining accuracy. For reducing the number of sensors and cost, highly accurate methods have been developed for the measurement of intake air mass, detection of acceleration, distinction of engine stroke, and estimation of atmospheric pressure without using a throttle position sensor, cam timing sensor, and barometric sensor in such a manner as to carry out sampling with the intake manifold pressure of single-cylinder engines synchronizing with the crank angle. For compactness and electric power saving, an injector and in-tank fuel pump module have been developed for small motorcycles.

Direct methanol fuel cell (DMFC) system is a compact lightweight system as it eliminates the need of a complex reformer unit. Moreover, since the methanol-water-solution used as fuel does not correspond to a flammable substance, it is thought that convenience is high. We have developed the hybrid scooter integrated with the DMFC system and the Li-ion rechargeable batteries, and optimized various parameters related to the performance and the efficiency. The power output of the DMFC system was adjusted to the value necessary for a constant ground run in 30 km/h of a commercial small electric scooter. All the system components had to be constituted in the limited space and under the restricted weight conditions. The net-power-output of the system was examined under various air flow rate, fuel flow rate and methanol concentration conditions.