Search Results

Magnesium alloys have been used and developed in applications for various motorcycle components and others such as cylinder head cover, crankcase and oil pan due to light weight, high specific strength and recycles ability. However, many of those alloys suffer from inferior die cast ability and high temperature properties, such as creep resistant. Ryobi limited has developed the creep resistant alloy in order to be utilized for the various motorcycle components and so forth. The properties of new die cast creep resistant alloy have been introduced. The targets for development of the properties of new alloy are the same creep resistant as aluminum die cast alloys and the same diecastability as ASTM magnesium alloys, such as AZ91D or AM60B alloys. Specific approaches of development with several types of evaluation have been performed for the purpose of fulfillment of this goal.

Combustion phenomena inside the actual Gasoline-Direct-Injection (GDI) engines have been drawing high attention to its emission characteristics as well as its potential to deal with ultra lean mixture. Although the detailed observation is necessary for its improvement, combustion visualization seems to be strangely overlooked for some reason. This study focuses on the direct observation of GDI combustion to clarify the difficulties behind GDI concept by using a test engine of an actual “wall-guided” configuration and by comparing GDI spray quality with diesel spray in a high-pressure constant volume bomb. The results show that some of the problems about GDI combustion seem to be rather essential than easily conquered, which suggests the necessity for another combustion concept.

Abnormal valve gear vibration is a perennial problem confronting the designer of high-performance 4-stroke engines. It would shorten time and reduce costs if an analytical method could be applied to the prediction of engine valve behavior. This paper describes a method of valve motion simulation for both SOHC and DOHC valve gears through interactive calculation and using computer graphics. The authors tried to set up as simple a simulation model as possible by using modal analysis and modeling techniques. Through setting simulation model parameters and experimental damping factors, a close correlation between calculated and actually measured results was found.

Two advanced combustion models have been validated with the KIVA-3V Release 2 code in the context of two-stage combustion in a heavy duty diesel engine. The first model uses CHEMKIN to directly integrate chemistry in each computational cell. The second model accounts for flame propagation with the G-equation, and CHEMKIN predicts autoignition and handles chemistry ahead of and behind the flame front. A Damköhler number criterion was used in flame containing cells to characterize the local mixing status and determine whether heat release and species change should be a result of flame propagation or volumetric heat release. The purpose of this criterion is to make use of physical and chemical time scales to determine the most appropriate chemistry model, depending on the mixture composition and thermodynamic properties of the gas in each computational cell.

Considerable amounts (400 ∼ 600 thousand tons) of waste vegetable oil in Japan are still flushed down the drain every year. Utilization of waste vegetable oil for diesel fuel leads to two advantages for environmental protection, to reduce CO2 emission from engines and to avoid water pollution of rivers. In this study, combustion characteristics of waste vegetable oil methyl ester (WME) are investigated in detail by not only engine test run but also observation of burning flames in a visual engine. As results indicate, WME shows rather better combustion state in the visual engine and lower smoke emission from a high-speed DI test engine than gas oil. Moreover, by emulsifying WME with water, further improvement of combustion and more than 18 % reduction of NOx emission is carried out.

The heavy-duty diesel engine industry is required to meet stringent emission standards. There is also the demand for more fuel efficient engines by the customer. In a previous study on an engine with variable intake valve closure timing, the authors found that an early single injection and accompanying premixed charge compression ignition (PCCI) combustion provides advantages in emissions and fuel economy; however, unacceptably high peak pressures and rates of pressure-rise impose a severe operating constraint. The use of a Pressure Reactive Piston assembly (PRP) as a means to limit peak pressures is explored in the present work. The concept is applied to a heavy-duty diesel engine and genetic algorithms (GA) are used in conjunction with the multi-dimensional engine simulation code KIVA-3V to provide an optimized set of operating variables.

This paper concerns a torque control of a rear wheel of a motorcycle equipped with a rubber/aramid belt electronically-controlled continuous variable transmission where a primary sheave position is controlled by an electric motor. In particular, the paper discusses a method to calculate a required engine torque and a required primary sheave position, given reference values of a rear-wheel torque and an engine rotational velocity. The method forms a foundation of a hierarchized traction control where a higher control layer decides an optimal motorcycle motion (rear-wheel torque and engine rotational velocity) and a lower control layer realizes the motion by actuators (engine torque and primary sheave position). Difficulties of the control are due to large mechanical compliance of the rubber/aramid belt, which leads to an inevitable lag from the primary sheave position to a speed reduction ratio.

This paper is a continuation of an earlier paper, which examined the steady-state internal heat transfer in the exhaust system of a diesel powered, light-duty vehicle. The present paper deals with the heat transfer of the exhaust system during two types of transient testing, as well as, the estimation of the exhaust systems external heat transfer. Transient heat transfer was evaluated using: a simple fuel-step transient under constant speed and the New European Driving Cycle (NEDC). The thermal response of the external walls varied considerably for the various components of the exhaust system. The largest percent difference between the measured temperatures and the corresponding quasi-steady estimates were about 10%, which is attributed to thermal storage. Allowing for thermal storage resulted in an excellent agreement between measurements and analysis.

A numerical study of the effects of injection parameters and operating conditions for diesel-fuel HCCI operation is presented with consideration of Variable Geometry Sprays (VGS). Methods of mixture preparation are explored that overcome one of the major problems in HCCI engine operation with diesel fuel and conventional direct injection systems, i.e., fuel loss due to wall impingement and the resulting unburned fuel. Low pressure injection of hollow cone sprays into the cylinder of a production engine with the spray cone angle changing during the injection period were simulated using the multi-dimensional KIVA-3V CFD code with detailed chemistry. Variation of the starting and ending spray angles, injection timing, initial cylinder pressure and temperature, swirl intensity, and compression ratio were explored. As a simplified case of VGS, two-pulse, hollow-cone sprays were also simulated.

Measurement using a three-dimensional anemometric-tester was made for the gas flow inside the cylinder of a two-stroke engine while the shape of the transfer port was modified. The relationship between port shape and engine performance was investigated for various factors that characterize the flow in cylinder. In this paper, we focused mainly on two engine running conditions: the maximum output at 11750 rpm and the output at 10000 rpm. As a result, we found that the maximum output is most related to the tangential inclination angles of the main transfer port, and the inner vent radius of the main transfer duct.

Mixture formation is one of the most important factors for the combustion in the spark ignition engine with port fuel injection. The relation between combustion and mixture quality, however, is not quantitatively well established. In this study, the connection of combustion and mixture formation was explored with various measurement techniques. Borescopes were used in order to investigate the flame propagation in the combustion chamber and behavior of spray and fuel film on the wall in the intake port. For the purpose of investigation on the effect of mixture formation, various port fuel injection systems and parameters were tested and compared: direction, timing, and size of droplet. An SI engine for small vehicle was used under condition of 4 000 rpm. The investigation by images obtained has shown that inhomogeneity of mixture causes low combustion stability, especially due to direct introduction of fuel droplets into the combustion chamber.

The demands on internal combustion engines for low emissions and fuel consumption are increasing year by year. On the other hand, engines to be used in motorcycles need to provide high output and quick response to meet user desire. In order to realize low fuel consumption while keeping high performance, it is necessary to properly understand cyclic variations during combustion as well as the influence of the injection system on fuel control during transient periods. The current paper reports on the results of a study in the influence of port fuel injection on combustion stability in a small displacement motorcycle engine, using both a series of experiments and CFD. The parameters of the injection systems under study are: (1) injection targeted area, (2) injection timing, and (3) fuel droplet size. The results of the current study show that injection aimed at the upstream wall yielded the best combustion stability.

Multidimensional models require physical inputs about the engine operating conditions. This paper explores the effects of unavoidable experimental uncertainties in the specification of important parameters such as the start of injection, duration of injection, amount of fuel injected per cycle, gas temperature at IVC, and the spray nozzle hole diameter. The study was conducted for a Caterpillar 3401 heavy-duty diesel engine for which extensive experimental data is available. The engine operating conditions include operation at high and low loads, with single and double injections. The computations were performed using a modified version of the KIVA3V code. Initially the model was calibrated to give very good agreement with experimental data in terms of trends and also to a lesser degree in absolute values, over a range of operating conditions and injection timings.

We studied the mechanism of occurrence and evaluation of the surge that is produced in motorcycles equipped with 2-stroke cycle engines by simultaneously measuring chassis behavior and combustion. When modal analysis was performed by measuring the acceleration of each chassis component while placing the test vehicle on a chassis dynamo, it was found that pitching, in which the tires serve as springs, and resonance, generated from the rear suspension spring, occurred simultaneously during surge generation. The major component that is felt physically is pitching. Although a certain degree of correlation was observed between fluctuations in combustion and occurrence of pitching, since the drive line contains a large amount of back lash, the system has a high degree of non-linearity, thus making it difficult to obtain a well-defined correlation.

The effects of residual gas mixing were studied in a single-cylinder, air-cooled utility engine using both external exhaust gas recirculation (EGR) and internal residual retention. EGR was introduced far upstream of the throttle to ensure proper mixing. Internal residual was changed by varying the length of the valve overlap period. EGR was measured in the intake system; the total in-cylinder diluent was directly measured using a skip-fire, cylinder dumping technique. A sweep of diluent fraction was performed at different engine speeds, engine loads, fuel mixture preparation systems, and ignition timings. An optimum level of diluent, where the combined hydrocarbon and NOx emissions were minimal, was found to exist for each operating condition. Higher levels of diluent, either through internal retention or external recirculation, caused the combined emissions to increase.

A monolithic type aluminum (Al) cylinder made of hypereutectic Aluminum-Silicon alloy has been widely used for motorcycle applications. It has a lightweight structure and a superior cooling ability owing to its material property and surface finishing. Usually the cylinder bore surface of the monolithic type Al cylinder is finished by an etching process or a honing process in order to expose silicon (Si) particles from aluminum (Al) matrix for the improvement of the tribological properties. The morphology of the cylinder bore surface including the exposure of Si particles is supposed to make an important effect on its tribological properties, especially on the anti-scuffing property. In this research, the anti-scuffing property of three kinds of cylinder bore finishing, an etched surface, a Si exposure honed surface and a conventional plateau honed surface is evaluated with using a reciprocated type wear tester. The experimental results are analyzed by using Weibull analysis.

All the primary inertia forces and/or moments generated by engines having three cylinders or less are not normally in balance by themselves and thus may be a great source of vibration for the frame supporting the engine. If the mass distribution of the crankwebs is selected in a proper manner, it is possible to determine arbitrarily the directions and the length ratio of principal axes of ellipses, which are obtained as Lissajous diagrams of inertia force and moment. This method can be effectively applied to reduce vibration in the frames. In this paper the appropriate inertia force and moment ellipse equations are developed and the analysis is outlined for optimizing the engine balance. Also the fundamental properties of the linear vibration systems excited by the elliptical forces as well as some experimental examples of elliptical excitation are detailed.

It is effective in engine fuel economy to reduce the viscous friction by applying lubricating oil with low viscosity. The lower viscosity such as SAE0W20, however, increase lubricating oil consumption, LOC. In addition, it has become urgent to reduce the LOC because the emission of the sulfide ash, phosphorous and sulfur contents degrades the diesel particulate filter and the de-NOx catalyst, in addition to which the emission of metal oxide contents from oil additives can cause pre-ignition in highly supercharged spark ignition engines. In order to clarify the LOC mechanism of low viscosity oils, the LOC rates were measured with a supercharged diesel engine under various operating conditions when lubricated with SAE30 or SAE10W30 test oil, and the resulting data have been compared with the rates of the evaporation from the oil-film on the cylinder wall, LOE, as predicted by the devised analysis method for multi-species component oils.

Gasoline fueled Homogeneous Charge Compression Ignition (HCCI) combustion with internal exhaust gas re-circulation using Negative Valve Overlap (NOL) was investigated by means of calculation and experiment in order to apply this technology to practical use with sufficient operating range and with acceptable emission and fuel consumption. In this paper we discuss the basic characteristics of NOL-HCCI with emphasis on the influence of intake valve timing on load range, residual gas fraction and induction air flow rate. Emission and fuel consumption under various operation conditions are also discussed. A water-cooled 250cc single cylinder engine with a direct injection system was used for this study. Three sets of valve timing were selected to investigate the effect of intake valve opening duration. Experimental results demonstrated that an engine speed of approximately 2000rpm yields an NMEP (Net Mean Effective Pressure) range from 200kPa to 400kPa.

The Bonded Valve Seat System is the latest technology to realize drastic reduction in valve temperature in SI engines characterized by the good thermal conductivity of extremely thin valve seats bonded directly on the aluminum cylinder head. A unique and highly rationalized resistance bonding technique was developed to maintain adequate bonding strength and positioning precision in a short bonding period of around one second. Engineering data on optimization of bonding-section geometry, valve seat material and the surface treatment and bonding parameters were presented and discussed regarding the mechanism. The geometry of the bonding section of the cylinder head was optimized by FEM analysis so that the aluminum material should deform to embed the valve seat ring with the action of expelling the surface contamination and the oxide film. The bonding facility was modified so that the electrode axis should move flexibly according to distortion of the cylinder head during bonding.