Refine Your Search

Date

Date

Topic

Topic

Electrical systems Analysis methodologies Exhaust systems Failure modes and effects analysis (FMEA) Fuel consumption AGE-3 Aircraft Ground Support Equipment Committee

Search Results

Viewing 1 to 20 of 58
123Next >Last >>
Sort by title
Standard

VEHICLE ELECTRICAL SYSTEMS
2007-08-29
HISTORICAL
AIR1336A
This SAE Aerospace Information Report (AIR) considers the following major areas: 1 Major components and their ratings 2 Selection criteria for optimum design balance for electrical systems 3 Effects of operating conditions and environment on both maintenance and life of components 4 Trouble signals—their diagnosis and cure
Standard

VEHICLE ELECTRICAL SYSTEMS
1975-05-01
HISTORICAL
AIR1336
This document considers the following major areas: 1 Major components and their ratings 2 Selection criteria for optimum design balance for electrical systems 3 Effects of operating conditions and environment on both maintenance and life of components 4 Trouble signals -- their diagnosis and cure
Standard

Technical Manual Development for Ground Support Equipment
2002-07-23
HISTORICAL
AS4828
This document shall serve as a guide for format, style, and method of presentation for all material included in manufacturers' publications for ground support equipment (GSE). These requirements shall be observed throughout all publications except where modified by detail requirements for specific publications. AS4828 is not applicable to the development or revision of electronic test equipment user manuals and documents. This document is written in general terms by intention, and in most cases conform to recognized practices in the industry. In the event there is a question which is not specifically covered by this document, the user engineering department should be contacted for guidance before proceeding to the final phase of manual development. Each manual prepared by a manufacturer shall contain an introduction which shall include a brief statement explaining the organization, content, and method for using the manual.
Standard

SOLID-STATE FREQUENCY CONVERTER 400 HERTZ, 3-PHASE OUTPUT
1989-09-01
HISTORICAL
ARP1940
This specification covers the requirements for solid-state frequency converters with 480 [or 380] V 3-phase, 60 [or 50] Hz input and 115/200 V, 3-phase, 400 Hz output capable of powering aircraft type loads requiring MIL-STD-704D quality power. The frequency converter shall be a self-contained unit suitable for the environment of intended use. Typical applications include dedicated use at passenger loading bridges (mounted under the bridge in telescoping bridge applications or fixed installation at base of stationary type loading bridges) with weatherproof enclosures or hangar/lab use where indoor fixed or portable units can be used.
Standard

SELECTION CRITERIA FOR RECIPROCATING PRIME MOVERS
1989-10-01
HISTORICAL
ARP1052
This Recommended Practice covers the following categories: a Basic engine rating (requirements for) - (Para. 3) b Suggested minimum conditions for selection - (Para. 4) c Recommended horsepower rating reductions - (Para. 5) d Special considerations - (Para. 6) e Recommended safety devices - (Para. 7) f Recommended minimum instrumentation - (Para. 8) g Recommended selection support data - (Para. 9) h Recommended usage of ARP - (Para. 10)
Standard

Regional Aircraft Towbarless Tow Vehicle - Test Requirements
2022-03-30
CURRENT
ARP5911A
The present Aerospace Recommended Practice specifies for airplane operator and tow vehicle manufacturers the basic testing requirements for towbarless tow vehicles to be used on the nose gear of conventional tricycle type landing gears of commercial civil transport aircraft with maximum ramp weight between 8600 kg (19 000 lb) and 50 000 kg (110 000 lb), commonly designated as “regional aircraft”. Its purpose is to achieve testing results, or equivalent computer modeling, demonstrating that the loads induced by the tow vehicle will not exceed the design loads of the airplane’s nose landing gear and associated structure, reduce the certified safe life limit of the nose landing gear, or otherwise compromise the airplane’s structural integrity and airworthiness certification.
Standard

Minimum Safety Requirements for Special Purpose Airline Ground Support Equipment
2014-05-29
CURRENT
AIR1375D
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
Standard

Minimum Safety Requirements for Special Purpose Airline Ground Support Equipment
2000-06-01
HISTORICAL
AIR1375C
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
Standard

Method of Evaluating Pneumatic Ground Power Units
2020-09-23
CURRENT
AIR4545A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
Standard

Maintenance of Batteries and Battery Charging and Servicing Facilities
2020-09-23
CURRENT
AIR1898A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/ maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

MINIMUM SAFETY REQUIREMENTS FOR SPECIAL PURPOSE AIRLINE GROUND SUPPORT EQUIPMENT
1998-09-01
HISTORICAL
AIR1375B
This document applies to special purpose equipment, excluding fixed facilities, which is used in the ground handling, servicing, and maintenance of aircraft. Equipment covered under other sections of the Federal Register Part 1910 is excluded from this document. This document is to establish minimum safety requirements and should not be used for vehicle design criteria. Equipment existing prior to publication date is excluded from the requirements of this document.
Standard

MAINTENANCE OF BATTERIES AND BATTERY CHARGING AND SERVICING FACILITIES
1992-06-10
HISTORICAL
AIR1898
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

Impulse Towing Loads
2023-04-03
CURRENT
AIR6906
This SAE Aerospace Information Report (AIR) provides information about impulse loads that occur during normal aircraft towing operations. An instrumented tow bar was used to characterize towing loads. Suggestions to minimize impulse loads by reducing the tow bar to tow vehicle gap are described.
Standard

Ground Support Equipment Electrical Systems
2018-09-27
CURRENT
AIR1336B
This SAE Aerospace Information Report (AIR) considers the following major areas: 1 major components and their ratings; 2 selection criteria for optimum design balance for electrical systems; 3 effects of operating conditions and environment on both maintenance and life of components; 4 trouble signals - their diagnosis and cure.
123Next >Last >>
X