Search Results

Analytical reverse projection is introduced and is shown to offer an improvement in applicability and accuracy over other techniques of single-image photogrammetry, including plane-to-plane transformation and camera reverse-projection methods. A comparison of the methods is made on the basis of a single case of reconstructing missing tire tracks on a roadway intersection. Advantages and disadvantages of each method are discussed. THIS PAPER REVIEWS non-graphical techniques used to make measurements of features imaged in a single photograph. Two formulations of the plane-to-plane transformation method are re viewed, the camera reverse-projection technique is presented, and a third technique, called the analytical reverse-projection method, is introduced. Following a review of the various methods, including an indication of their advantages and disadvantages, each method is applied to the problem of relocating a set of tire tracks in an intersection.

This paper summarizes the development of an Instrumented faceform which can record time histories of impact-related pressures at fifty-two locations over the entire face of a Hybrid 2 crash dummy skull. Pressures are measured by using piezo-electric, thin-plastic films; a high-speed, multiplex data acquisition system; signal conditioning; a software-controlled computerized data reduction and recording scheme; and a submergence calibration technique. The construction of the modified dummy face and the calibration gear are discussed. Examples of preliminary laboratory impact test results are presented. Theory and techniques relating to signal processing software, microprocessor controlled random-access-memory data-retrieval system and system calibration are also discussed. It is hoped that this tool, now undergoing final development and verification testing, will find extensive use in the evaluation and safety-related design of vehicle interiors and occupant restraints.

The relatively rare occurrence of injury or fatality in fuel-fed fires has received considerable attention in automotive safety rulemaking and products liability litigation. The literature related to fatalities associated with fire is confirmed by recent FARS data, and there are no reliable field data which confirm a need for further injury-reducing effect related to FMVSS 301. NHTSA has acknowledged this by removing crash fire rulemaking from its priorities plan. The police-reported crash fire data now available must be supplemented with in-depth investigation by trained teams before informed judgements can be made regarding further safety improvements with respect to crash fire injury.

The NHTSA notices of proposed rulemaking on side impact protection have focused worldwide attention on one of the most difficult and frustrating efforts in automobile crash safety. Traditional vehicle design has evolved obvious structural contrasts between the side of the struck vehicle and the front of the striking vehicle. Protection of near-side occupants from intruding door structure is a most perplexing engineering challenge. Much useful and insightful engineering work has been done in conjunction with NHTSA's proposed rulemaking. However, there are many major engineering issues which demand further definition before reasonable side impact rulemaking test criteria can be finalized. This paper reviews recent findings which characterize the human factors, biomechanics, and occupant position envelope of the typical side impact crash victim.

An economical alternative technique is presented for obtaining vehicle frontal crush characteristics from a series of repeated low speed barrier crashes. Results were analyzed using a technique of linear correlation of residual crush depth with a defined crush energy parameter. The data compared closely with crashes reported in the literature, and suggested that the structure exhibits only a slight strain rate sensitivity. Crush energy is shown to correlate well with dynamic crush depth. Relations among dynamic and residual crush and recovery distance are reported, Velocity restitution is shown to be about constant at 15% over the impact velocity range employed. A force-deflection relation based on the offset force linear harmonic oscillator theory is suggested, shown to agree quite well with data. Repeated crash testing can be an effective method to obtain information needed for development of analytical and predictive tools useful in design and reconstruction.

Rollover crashes involving side-by-side ATVs and injuries related to these crashes represent an increasing percentage of the total population of ATV injury crashes. Unlike traditional ATVs, side-by-side ATVs are designed to carry two passengers abreast and usually include roll bars and seat belts. Most side-by-side ATVs are also designed to carry a limited payload in a rear cargo bed. Primary target uses for these vehicles include a combination of utilitarian tasks and recreational activities. Modifications by consumers often incorporate additional equipment that can change the mass balance and handling characteristics of the vehicle. This paper explores the resistance of these vehicles to roll as affected by the variables commonly applied to automotive crashes. Static Stability Factor (SSF) and Critical Sliding Velocity (CSV) are calculated and compared to findings from previously published work on roll resistance.

While vehicular rear pole impacts are rare, they do occur, and can be very serious. General accident reconstruction methods, which derive vehicle stiffness values from rear barrier crash tests, over-predict the impact speed for these types of pole impacts. Thirteen pole crash tests were run into the rear-ends of four 4-door, front-wheel drive sedans. Repeated crash testing was used on three of the vehicles. Two 1988 Acura Legends, which have one of the highest stiffness values from FMVSS 301 Rear Compliance crash testing, a 1988 Honda Civic, which has one of the softest rear-end stiffnesses, and a 1986 Ford Taurus were tested. The repeated crash testing methodology was validated using one of the 1988 Acura Legends and a previously published Ford Taurus test. Residual crush was measured using maximum crush, point-to-point, longitudinal full-width, and longitudinal reduced-width methodologies. Crush was found to be linearly related to impact speed.

One of the greatest challenges faced in the design of realistic occupant protection systems is an accurate statistical model of what is really needed. The paucity of data is this realm hinders designers of standards alike. Ideally, a model of crash statistics would correlate, for significant accident modes, injury level (as measured by AMA Abreviated Injury Scale “AIS”) with some adequate measure of crash intensity. Having this information, not only could the required level of safety design be ascertained, but also the justifiable economic expenditure could be estimated. This paper treats the statistical basis for deployment of a data retrival system. It provides a basis for estimates of the amount of data required, the number of vehicles to be instrumented, the crash severity trigger levels, and the economics of recorder installation, for various levels of injury and fatality.

An understanding of fundamental kinematic relationships among the several deforming surfaces of side-impacting bullet and target vehicle, occupant protection system and occupant is fundamental to rational design of crash injury counter-measures. Unfortunately, such understanding is not easy to achieve. Side impacts address the full range of bodily contacts and injuries in a way that challenges analysis. Each bodily area and organ requires individual consideration for adequate injury protection. This paper presents a simplified graphical analysis of occupant kinematics and injury exposure applied specifically to the NHTSA-proposed crabbed moving deformable barrier (MDB) compartment impact, as described in NHTSA's Notice of Proposed Rulemaking (NPRM) for Federal Motor Vehicle Safety Standard (FMVSS) 214, issued in January of 1988 [NHTSA 1988 (1)*]. Projections are offered regarding the potential of thoracic injury counter-measures.

Thoracic impact response and injuries of living and postmortem porcine siblings were investigated to quantify comparative differences. Thirteen male animals, averaging 61.4 kg, from five different porcine litters comprised the two animal samples. Porcine brothers were subjected to similar impact exposures for which at least one brother was tested live, anesthetized and another dead, post rigor with vascular repressurization. Statistically significant differences in biomechanical responses and injuries were observed between live and postmortem siblings. On the average the anesthetized live animals demonstrated a greater thoracic compliance, as measured by increased normalized total deflections (21% Hi), and reduced overall injuries (AIS 14% Lo and rib fractures 26% Lo) at lower peak force levels (13% Lo) than did the postmortem subjects. However, individual comparisons of “match-tested” siblings demonstrated very similar responses in some cases.

This paper presents a method of automobile collision analysis based on conservation of momentum. The analysis is applied to the collision of two two-dimensional bodies, either or both of which may be attached to a trailer. Newton's laws of motion are employed to determine changes in linear and angular velocities for the two-dimensional colliding bodies. Knowing the masses and rotational inertias and the initial velocities of all bodies at impact, the post-impact velocities can be calculated if appropriate constraints are applied to the bodies' post-collision motion. Various motion constraints, including lock-up, slip, and restitution are examined, and a methodology for modeling vehicle motion experienced during a collision is presented. The full set of basic equations characterizing this conservation-of-momentum analysis is presented with sufficient detail to allow their implementation on a programmable calculator or personal computer.

Collision Safety Engineering, Inc. (CSE), has developed a test prototype system to protect occupants during lateral impacts. It is an inflatable system that offers the potential of improved protection from thoracic, abdominal and pelvic injury by moving an impact pad into the occupant early in the crash. Further, it shows promise for head and neck protection by deployment of a headbag that covers the major target areas of B-pillar, window space, and roofrail before head impact. Preliminary static and full-scale crash tests suggest the possibility of injury reduction in many real-world crashes, although much development work remains before the production viability of this concept can be established. A description of the system and its preliminary testing is preceded by an overview of side impact injury and comments on the recent NHTSA Rule Making notices dealing with side-impact injury.

Vehicle accident reconstruction methods based on deformation energy are argued to be an increasingly valuable tool to the accident reconstructionist, provided reliable data, reasonable analysis techniques, and sound engineering judgement accompany their use. The evolution of the CRASH model of vehicle structural response and its corresponding stiffness coefficients are reviewed. It is concluded that the deformation energy for an accident vehicle can be estimated using the CRASH model provided that test data specific to the accident vehicle is utilized. Published stiffness coefficients for vehicle size categories are generally not appropriate. For the purpose of estimating vehicle deformation energy, a straight-forward methodology is presented which consists of applying the results of staged crash tests. The process of translating crush profiles to estimates of vehicle deformation energies and velocities is also discussed.

The BSAN crash pulse model has been shown to provide useful information for restraint sensing evaluation and for structural force-displacement studies in flat fixed rigid barrier (FFRB) crashes. This paper demonstrates a procedure by which the model may be extended for use with central and offset vehicle to vehicle (VTV) crashes through appropriate combinations of vehicle parameters.

This project covers one facet of a program to develop a mechanical model for characterizing the time history of local forces on the zygomatic, maxillary and mandible regions of the human face during a frontal collision. Two mechanical devices to measure the forces on crash dummies during testing were designed, constructed and tested. The devices employed cantilever beams equipped with strain gauges. Both devices were subjected to a series of drop tests onto various materials. Time histories were compared to those obtained from cadaver experiments. While the data obtained from this testing appears to be similar to the cadaver data, further improvements and modifications will make the model much more useful.

A test method was developed whereby repeated pole impacts could be performed at multiple locations per test vehicle, allowing a comparison of energy and crush relationships. Testing was performed on vehicles moving laterally into a 12.75 inch diameter rigid pole barrier. Crush energy absorption characteristics at the different locations were analyzed, and the results compared to test data from broad moving barrier crashes and available crash tests with similar pole impacts. Crush stiffness characteristics for narrow impacts at various points on the side of the Taurus vehicle platform were documented. Factors encountered during the research include the importance of rotational energy accounting and uncertainties related to crush energy related to induced deformation. The findings show that the front axle and A-pillar regions are much stiffer than the CG and B-pillar areas to narrow rigid pole impact.

Development of a seat with an active adjustable seatback stiffness for enhanced safety during a rear impact is demonstrated. Review of literature suggests that there is not a single value for seatback stiffness to optimize occupant protection. An automobile seat whose stiffness can be actively adjusted based on EDR input and other factors can potentially enhance occupant safety during some rear impact crashes. Static pull tests were performed using a prototype seat demonstrating how seatback stiffness can be modified, and deformation limited, using electromechanical means. Research and development of this technology is ongoing.

Accident data suggest that a significant percentage of rear impacts involve occupants seated in other than a “Normal Seated Position”. Pre-impact acceleration due to steering, braking or a prior frontal impact may cause the driver to move away from the seat back prior to impact. Nevertheless, virtually all crash testing is conducted with dummies in the optimum “Normal Dummy Seated Position”. A series of 7 rear impact sled tests, having a nominal AV of 21 mph, with Hybrid III dummies positioned in the “Normal Dummy Seated Position”, “Out of Position” and slightly “Out of Position” is presented. Tests were performed on yielding production Toyota and Mercedes Benz seats as well as on a much stiffer modified Ford Aerostar seat. Available Hybrid III upper and lower neck as well as torso instrumentation was used to analyze and compare injury potential for each set of test parameters.

The reconstruction of accidental impacts to the side structure of one or more accident vehicles often incorporates estimates of the energy absorbed by laterally struck vehicle(s). Such estimates generally involve considerably more issues than does the assessment of frontal or rear impact deformation energy. The sides of vehicles are, compared to the usual striking object, relatively broad, and they contain zones of varying stiffness supported by collapsible box structures. Side stiffnesses can vary widely, depending upon impact geometry. Most side impact crash tests that can readily be used to make estimates of side stiffness have been conducted by the National Highway Traffic Safety Administration (NHTSA).

Results indicate the need for a redesigned Hybrid III face capable of accurate force and acceleration measurements. New instrumentation and methods for facial fracture detection were developed, including the application of acoustic emissions. Force/ deflection information for the human cadaver head and the Hybrid III ATD were generated for the frontal, zygomatic, and maxillary regions.