Search Results

Water injection (WI) can improve gasoline engine performance and efficiency, and on-board water recovery technology could eliminate the need for customers to refill an on-board water reservoir. In this regard, the technical feasibility of exhaust water recovery (EWR) is described in this paper. Water injection testing was conducted at a full load condition (5000 rpm/18.1 bar BMEP) and a high load condition (3000 rpm/14.0 bar BMEP) on a turbocharged gasoline direction injection (GTDI) engine. Water recovery testing was conducted both after the exhaust gas recirculation (EGR) cooler and after the charge air cooler (CAC) at a high load (3000 rpm/14.0 bar BMEP), as well as a part load (2080 rpm/6.8 bar BMEP) condition, at temperatures ca. 10-15 °C below the dew point of the flow stream. Three types of water separation designs were tested: a passive cyclone separator (CS), a passive membrane separator (MEM), and an active separator (AS).

As demand for wall-flow Diesel Particulate Filters (DPF) increases, accurate predictions of DPF behavior, and in particular their pressure drop, under a wide range of operating conditions bears significant engineering applications. In this work, validation of a model and development of a simulator for predicting the pressure drop of clean and particulate-loaded DPFs are presented. The model, based on a previously developed theory, has been validated extensively in this work. The validation range includes utilizing a large matrix of wall-flow filters varying in their size, cell density and wall thickness, each positioned downstream of light or heavy duty Diesel engines; it also covers a wide range of engine operating conditions such as engine load, flow rate, flow temperature and filter soot loading conditions. The validated model was then incorporated into a DPF pressure drop simulator.

A unique validation method is proposed for mount designs of Lean NOx Traps (LNT's), in which characteristic curves of failure points as functions of thermal cycles and vibration amplitudes are generated. LNT's are one of the several new types of emissions control devices applied to Diesel Exhaust Systems, and they reduce the amount of NOx through chemical adsorption. Desulfation must occur nearly every hour, which involves raising the inlet gas temperature of the LNT to around 700°C to “burn off” sulfur from the catalyst, which otherwise would decrease its catalytic activity. This temperature is held for several minutes, and its cyclic occurrence has a negative effect on the long-term performance of the support mat, a major component of its mount design. As substrate temperatures increase, shell temperatures do as well, and thermal growth differences between the ceramic substrate and metallic shell cause the gap between them, which is filled by the support mat, to increase.

As Selective Catalytic Reduction (SCR) NOx abatement systems gain commercial acceptance and popularity, the need for efficiency predictive capabilities increases. To this end, a flow bench was developed capable of varying steady state inputs (temperature, flow rate and NOx concentration). The efficiencies of various SCR systems was measured and compared. This concept of a steady state flow bench approach allows for an efficient and cost effective means to evaluate comparable system designs.

As emissions regulations around the world become more stringent, emerging markets are seeking alternative strategies that align with local infrastructures and conditions. A Lean NOx Catalyst (LNC) is developed that achieves up to 60% NOx reduction with ULSD as its reductant and ≻95% with ethanol-based fuel reductants. Opportunities exist in countries that already have an ethanol-based fuel infrastructure, such as Brazil, improving emissions reduction penetration rates without costs and complexities of establishing urea infrastructures. The LNC performance competes with urea SCR NOx reduction, catalyst volume, reductant consumption, and cost, plus it is proven to be durable, passing stationary test cycles and adequately recovering from sulfur poisoning. Controls are developed and applied on a 7.2L engine, an inline 6-cylinder non-EGR turbo diesel.

Diesel burners introduce combustion of diesel fuel to raise exhaust gas temperature to Diesel Oxidization Catalyst (DOC) light-off or Diesel Particulate Filter (DPF) regeneration conditions, thereby eliminating the need of engine measures such as post-injections. Such diesel combustion requirement nevertheless poses challenges to burner development especially in combustion control and risk mitigation of DPF material failure. In particular, burner design must satisfy good soot distribution and heat distribution at DPF front face after meeting minimum requirements of ignition, heat release, and backpressure. In burner development, Computational Fluid Dynamics (CFD) models have been developed based on commercial codes for burner thermal and flow management with capability of predicting comprehensive physical and chemical phenomena including turbulence induced mixing, fuel injection, fuel droplet transport, diesel combustion, radiation, conjugate heat transfer and etc.

A novel Spatially Optimized Diffusion Alloy (SODA) material has been developed and applied to exhaust systems, which are an aggressive environment subject to high temperatures and loads, as well as excessive corrosion. Traditional stainless steels disperse chromium homogeneously throughout the material, with varying amounts ranging from 10% to 20% dependent upon its grade (e.g. 409, 436, 439, 441, and 304). SODA steels, however, offer layered concentrations of chromium, enabling an increased amount along the outer surface for much needed corrosion resistance and aesthetics. This outer layer, typically about 70μm thick, exceeds 20% of chromium concentration locally, but is less than 3% in bulk, offering selective placement of the chromium to minimize its overall usage. Since this layer is metallurgically bonded, it cannot delaminate or separate from its core, enabling durable protection throughout manufacturing processes and full useful life.

Diesel particulate trap regeneration is a complex process involving the interaction of phenomena at several scales. A hierarchy of models for the relevant physicochemical processes at the different scales of the problem (porous wall, filter channel, entire trap) is employed to obtain a rigorous description of the process in a multidimensional context. The final model structure is validated against experiments, resulting in a powerful tool for the computer-aided study of the regeneration behavior. In the present work we employ this tool to address the effect of various spatial non-uniformities on the regeneration characteristics of diesel particulate traps. Non-uniformities may include radial variations of flow, temperature and particulate concentration at the filter inlet, as well as variations of particulate loading. In addition, we study the influence of the distribution of catalytic activity along the filter wall.

Diesel and gasoline direct injection engines emit nucleation mode particles either under special conditions or as part of their normally emitted size distribution, respectively. Currently, European legislation excludes nucleation mode particles as particle number vehicle emission measurements are limited down to 23 nm. The rationale behind such a cut-off size is based on the avoidance of significant uncertainties inherent in the sampling and measuring of sub-23 nm solid particles. However, the sub-23 nm particles have drawn increased attention since a large fraction of particles emitted by modern vehicles lies in this size range. In this study we investigate the possibility of accurate nucleation mode particles detection by using the Advanced Half Mini Differential Mobility Analyzer (HM-DMA).

In the present work we apply a computational simulation framework developed for square-cell shaped honeycomb Diesel Particulate Filters to study the filtration, pressure drop and soot oxidation characteristics of recently developed triangular-cell-shaped, high porosity wall-flow filters. Emphasis is placed on the evaluation of the applicability and adaptation of the previously developed models to the case of triangular channels. To this end Computational Fluid Dynamics, asymptotic analysis, multichannel and “unit-cell” calculations are employed to analyze filter behavior and the results are shown to compare very well to experiments available in the literature.

Catalysts and filters continue to be applied widely to meet particulate matter regulations across new and retrofit diesel engines. Soot management of the filter continues to be enhanced, including regeneration methodologies. Concerns regarding in-cylinder post-injection of fuel for active regeneration increases interests in directly injecting this fuel into the exhaust. Performance of secondary fuel injection layouts is discussed, and sensitivities on thermal uniformity are measured and analyzed, providing insight to packaging challenges and methods to characterize and improve application designs. Influences of end cone geometries, mixers, and injector mounting positions are quantified via thermal distribution at each substrate's outlet. A flow laboratory is applied for steady state characterization, repeated on an engine dynamometer, which also provides transient results across the NRTC.

Secondary fuel injection is applied to facilitate active soot management of the particulate filter within diesel aftertreatment systems, avoiding concerns with fuel delivery via in-cylinder post-injection. System performance is dependent on the thermo-fluid interactions of the injected fuel with the exhaust stream, with the intent of having more fully vaporized fuel and a well-mixed air-fuel mixture at the inlet of the oxidation catalyst for uniform thermal distribution as it exothermically reacts. Pre-heating the fuel with a diesel vaporizer prior to its delivery into the exhaust enables improved system performance, reducing droplet sizes and mixing demands. A diesel vaporizer is applied within the exhaust of a medium duty truck application, and the response of the catalyst is characterized across a variety of conditions.

Stringent global emissions legislation demands effective NOx reduction strategies, particularly for the aftertreatment, and current typical liquid urea SCR systems achieve efficiencies greater than 90% [1]. However, with such high-performing systems comes the trade-off of requiring a tank of reductant (urea water solution) to be filled regularly, usually as soon as the fuel fillings or as far as oil changes. Advantages of solid reductants, particularly ammonium carbamate, include greater ammonia densities, enabling the reductant refill interval to be extended several multiples versus a given reductant volume of urea, or diesel exhaust fluid (DEF) [2]. An additional advantage is direct gaseous ammonia dosing, enabling reductant injection at lower exhaust temperatures to widen its operational coverage achieving greater emissions reduction potential [3], as well as eliminating deposits, reducing mixing lengths, and avoiding freeze/thaw risks and investments.

This paper describes the joint development by Tenneco and Pi Shurlok of a complete diesel engine aftertreatment system for controlling particulate matter emissions. The system consists of a DOC, DPF, sensors, controller and an exhaust fuel injection system to allow active DPF regeneration. The mechanical components were designed for flow uniformity, low backpressure and component durability. The overall package is intended as a complete PM control system solution for OEMs, which does not require any significant additions to the OEM's engine control strategies and minimizes integration complexity. Thus, to make it easier to adapt to different engine platforms, ranging from small off-road vehicle engines to large locomotive engines, model-based control algorithms were developed in preference to map-based controls.

Current progress in the development of diesel engines substantially contributes to the reduction of NOx and Particulate Matter (PM) emissions but will not succeed to eliminate the application of Diesel Particulate Filters (DPFs) in the future. In the past we have introduced a Multi-Functional Reactor (MFR) prototype, suitable for the abatement of the gaseous and PM emissions of the Low Temperature Combustion (LTC) engine operation. In this work the performance of MFR prototypes under both conventional and advanced combustion engine operating conditions is presented. The effect of the MFR on the fuel penalty associated to the filter regeneration is assessed via simulation. Special focus is placed on presenting the performance assessment in combination with the existing differences in the morphology and reactivity of the soot particles between the different modes of diesel engine operation (conventional and advanced). The effect of aging on the MFR performance is also presented.

This study investigates the passive regeneration behavior of diesel particulate filters (DPFS) with various PGM loadings under different engine operating conditions. Four wall-flow DPFs are used; one uncoated and three wash-coated with low, medium, and high PGM loadings, with and without an upstream diesel oxidation catalyst (DOC). DPFs with variable pre-soot loads are evaluated at two steady state temperatures (300°C and 400°C), as well as across three levels of transients based on the 13-mode ESC cycle. Passive regeneration rates are calculated based on pre and post soot gravimetric measurements along with accumulated soot mass rates for specified exhaust mass flow rates and temperatures. Results illustrate the effect of temperature, NO₂ content, and soot loading on passive regeneration without upstream DOCs or DPF wash coatings.

The introduction of stringent EPA 2015 regulations for locomotive / marine engines and IMO 2016 Tier III marine engines initiates the need to develop large diesel engine aftertreatment systems to drastically reduce emissions such as SOx, PM, NOx, unburned HC and CO. In essence, the aftertreatment systems must satisfy a comprehensive set of performance criteria with respect to back pressure, emission reduction efficiency, mixing, urea deposits, packaging, durability, cost and others. Given multiple development objectives, a systematic approach must be adopted with top-down structure that addresses top-level technical directions, mid-level subsystem layouts, and bottom-level component designs and implementations. This paper sets the objective to provide an overview of system development philosophy, and at the same time touch specific development scenarios as illustrations.

In order to satisfy tightening global emissions regulations, diesel truck manufacturers are striving to meet increasingly stringent Oxides of Nitrogen (NOx) reduction standards. The majority of heavy duty diesel trucks have integrated urea SCR NOx abatement strategies. To this end, aftertreatment systems need to be properly engineered to achieve high conversion efficiencies. A EuroV intent urea SCR system is evaluated and failed to meet NOx conversion targets with severe urea deposit formation. Systematic enhancements of the design have been performed to enable it to meet targets, including emission reduction efficiency via improved reagent mixing, evaporation, distribution, back pressure, and removing of urea deposits. Multiple urea mixers, injector mounting positions and various system layouts are developed and evaluated, including both CFD analysis and full scale laboratory tests.

In recent years advanced computational tools of Diesel Particulate Filter (DPF) regeneration have been developed to assist in the systematic and cost-effective optimization of next generation particulate trap systems. In the present study we employ an experimentally validated, state-of-the-art multichannel DPF simulator to study the regeneration process over the entire spatial domain of the filter. Particular attention is placed on identifying the effect of inlet cones and boundary conditions, filter can insulation and the dynamics of “hot spots” induced by localized external energy deposition. Comparison of the simulator output to experiment establishes its utility for describing the thermal history of the entire filter during regeneration. For effective regeneration it is recommended to maintain the filter can Nusselt number at less than 5.

As different Diesel Particulate Filter (DPF) designs and media are becoming widely adopted, research efforts in the characterization of their influence on particle emissions intensify. In the present work the influence of a Diesel Oxidation Catalyst (DOC) and five different Diesel Particulate Filters (DPFs) under steady state and transient engine operating conditions on the particulate and gaseous emissions of a common-rail diesel engine are studied. An array of particle measuring instrumentation is employed, in which all instruments simultaneously measure from the engine exhaust. Each instrument measures a different characteristic/metric of the diesel particles (mobility size distribution, aerodynamic size distribution, total number, total surface, active surface, etc.) and their combination assists in building a complete characterization of the particle emissions at various measurement locations: engine-out, DOC-out and DPF-out.