Search Results

Many applications of liquefied petroleum gas (LPG) to commercial vehicles have used their corresponding diesel engine counterparts for their basic architecture. Here a review is made of the application to commercial vehicle operation of a robust 4 L, light-duty, 6-cylinder in-line engine produced by Ford Australia on a unique long-term production line. Since 2000 it has had a dedicated LPG pick-up truck and cab-chassis variant. A sequence of research programs has focused on optimizing this engine for low carbon dioxide (CO₂) emissions. Best results (from steady state engine maps) suggest reductions in CO₂ emissions of over 30% are possible in New European Drive Cycle (NEDC) light-duty tests compared with the base gasoline engine counterpart. This has been achieved through increasing compression ratio to 12, running lean burn (to λ = 1.6) and careful study (through CFD and bench tests) of the injected LPG-air mixing system.

A fleet of 50, 1986-1987 model year cars designed for unleaded gasoline has been tested on the road and on a chassis dynamometer over 5 driving cycles and a wide range of other manoeuvres including steady speeds. It was found that the fuel consumption of this fleet was 17 to 23% (depending on test cycle) less than that of a corresponding fleet to leaded fuelled cars of 1980 model year average. Exhaust emissions were significantly lowered in the range of 45 to 93%. However trend line analysis of the several data sets indicates that the ULG fleet has about 6% higher fuel consumption than would have been expected if there had been a continuing evolution of leaded vehicle technology. The data base produced has applicability to a wide range of planning and design tasks, and those illustrated indicate the effects of speed limit changes and advisory speed signs on fuel consumption and emissions.

This paper presents a combined experimental and numerical method for analysing energy flows within a spark ignition engine. Engine dynamometer data is combined with physical models of in-cylinder convection and the engine's thermal impedances, allowing closure of the First Law of Thermodynamics over the entire engine system. In contrast to almost all previous works, the coolant and metal temperatures are not assumed constant, but rather are outputs from this approach. This method is therefore expected to be most useful for lean burn engines, whose temperatures should depart most from normal experience. As an example of this method, the effects of normalised air-fuel ratio (λ), compression ratio and combustion chamber geometry are examined using a hydrogen-fueled engine operating from λ = 1.5 to λ = 6. This shows large variations in the in-cylinder wall temperatures and heat transfer with respect to λ.

The 2023 FISITA White Paper (for which the author was a contributor) on managing in-service emissions and transportation options, to reduce CO2 (CO2-e or carbon footprint) from the existing vehicle fleet, proposed 6 levers which could be activated to complement the rapid transition to vehicles using only renewable energy sources. Another management opportunity reported here is optimizing the vehicle’s life in-service to minimize the life-cycle CO2 impact of a range of present and upcoming vehicles. This study of the US vehicle fleet has quite different travel and composition characteristics to European (EU27) vehicles. In addition, the embodied CO2 is based on ANL’s GREET data rather than EU27 SimaPro methodology. It is demonstrated that in-service, whole-of-life mileage has a significant influence on the optimum life cycle CO2 for BEVs and H2 fuelled FCEVs, as well as ICEs and PHEVs.

The specific power densities and therefore the level of sophistication and costs of FIM-MOTOGP engines 800 cm3 in capacity have reached levels similar to those of the traditionally much more expensive FIA-Formula One engines and some racing developments have no application at all in the development of production bikes. The aim of the paper is therefore to review FIM-MOTOGP engine rules and make recommendations that could reduce costs and make racing more directly relevant to the development of production bikes while enhancing the significant interest in technical innovation by the sports' fans.

This paper focuses on the combustion system development and combustion analysis results for a normally aspirated 0.43-liter small engine. The inline two-cylinder engine used in experiments has been tested in a variety of normally aspirated modes, using 98-RON pump gasoline. Test modes were defined by alterations to the induction system, which included carburetion and port fuel injection fuel delivery systems. The results from this paper provide some insight into the combustion effects for small cylinder normally aspirated spark ignition engines. This information provides future direction for the development of smaller engines as oil prices fluctuate and CO₂ emissions begin to be regulated. Small engine combustion is explored with a number of parametric studies, including a range of manifold absolute pressures up to wide open throttle, engine speeds exceeding 10,000 rev/min and compression ratios ranging from 9 to 13.

Gasoline Direct Injection (DI) is a technique that was successful in motor sports several decades ago and is now relatively popular in passenger car applications only. DI gasoline fuel injectors have been recently improved considerably, with much higher fuel flow rates and much finer atomization enabled by the advances in fuel pressure and needle actuation. These improved injector performance and the general interest in reducing fuel consumption also in motor sports have made this option interesting again. This paper compares Port Fuel Injection (PFI) and DI of gasoline fuel in a high performance, four cylinder spark ignition engine for super bike racing. Computations are performed with a code for gas exchange, heat transfer and combustion, simulating turbulent combustion and knock.

The Australian Concept Car was developed with support from a wide range of industry and government sectors. The estimated energy consumption over the vehicle life cycle is presented relative to a typical Australian Upper Medium Class car fleet. Several assumptions are made about the performance of the prototype car, when extrapolating it to a production counterpart for the comparison. Production methods are one area, covered by a survey of suppliers, and particularly in-service fuel use has had to be estimated using validated procedures. Uncertainties exist about the level of recycling at the end of the vehicles projected life after 225,000 km, leading to defined uncertainties. It is concluded that the concept car will have an energy reduction of 15-17.5% and the life cycle CO2 emissions will be reduced by a little less.

This paper details the development of a compressed natural gas (CNG) engine with ultra lean burn low emissions potential. Hydrogen assisted jet ignition (HAJI) is used to achieve reliable combustion and low NOx emissions, whilst direct injection is used to improve thermal efficiency and decrease hydrocarbon (HC) emissions. It is found that port inducted propane, port inducted CNG and directly injected CNG all produce negligible levels of CO and NOx when operating at air/fuel ratios higher than λ = 1.8. Furthermore, direct injection of CNG produced approximately 100 ppm C6 less HC emissions than port induction of CNG, and port induction of CNG decreased the HC emissions by around a factor of a third to a half in comparison with port induction of propane.

In this paper the experimental performance of the lean limits is examined for two different types of engines the first a dedicated LPG high compression ratio 2-valve per cylinder engine (Ford of Australia MY 2001 AU Falcon) and the second a gasoline moderate compression 4-valve per cylinder variant of the same engine (Ford of Australia MY 2006 BF Falcon). The in-cylinder composition at the lean limit over a range of steady state operating conditions is estimated using a quasi-dimensional model. This makes it possible to take into account the effects of both residual fraction and fresh charge diluents (EGR and excess air) that allow the exploration of a modeled lean limit performance [1, 2]. The results are compared to the predictions from a model for combustion variability applied to the quasi-dimensional model operating in optimization mode.

Cyclic variability in spark ignition engine combustion, especially at high dilution through lean burn or high EGR rates, places limits on in-cylinder NOx reduction and thermal efficiency. Flame wrinkling, resulting from interactions with turbulence, is a potential source of cyclic variations in turbulence. Previous studies have shown that flame kernels are subject to significant distortions when they are smaller than the integral length scale of turbulence. With the assumption that flame development is not subject to noticeable variations, after it reaches the integral length scale, the authors have shown that turbulent-burning-caused combustion variability can be successfully modeled as a function of laminar flame speed and turbulence intensity. This paper explores the contributions of flame wrinkling to flame kernel growth variation. As the kernel growth problem is complex, this study only explores one of the many aspects of the problem.

Gas assisted jet ignition is an advanced prechamber ignition process that allows ignition of ultra lean mixtures in an otherwise standard spark ignition engine. The results presented in this paper indicate that in a gas assisted jet ignition system fuelled with LPG in both the main chamber and prechamber, the lean limit can be extended to between λ = 2-2.35, depending on the load and speed. Although the fuel combinations that employ H2 as the prechamber fuel can extend the lean limit furthest (λ = 2.5-2.6), the extension enabled by the LPG-LPG prechamber-main chamber combination provides lower NOx emission levels at similar λ. In addition, when LPG is employed in place of gasoline as the main chamber fuel, hydrocarbon emissions are significantly reduced, however with a slight penalty in indicated mean effective pressure due to the gaseous state of the LPG.

The HAJI (Hydrogen Assisted Jet Ignition) system for S.I. engines utilises direct injection of small amounts of hydrogen to enhance the combustion of a variety of automotive fuels. Although not the primary purpose of HAJI, the hardware, once in place, also lends itself to the possibility of hydrogen-only running during a cold start. Cold-start simulations have been performed using a single cylinder engine. Results are presented, comparing hydrogen-only tests with standard HAJI operation and normal spark-ignition operation. HAJI and spark ignition tests were carried out with gasoline as the main-chamber fuel. Emission levels and combustion stability characteristics were recorded as the engine warmed up. The differences between the various fueling/ignition scenarios are presented and the implications for possible automotive applications are discussed in light of current and proposed emissions legislation.

This paper presents a study of the performance of a lean burn, natural gas-fuelled, naturally aspirated, spark ignition engine for an E class vehicle. Engine performance and exhaust emissions (NO, CO, and UHC) data are first discussed. An energy balance of the engine operating at different loads and air-fuel ratios is then presented, and used to explain why engine efficiency varies with air-fuel ratio. Finally, the hot start drive cycle CO2e (CO2 equivalent) emissions are estimated for a vehicle with this engine. This shows a potential for significant reduction in vehicle greenhouse gas emissions compared to an equivalent gasoline-fuelled vehicle.

A high compression ratio, single cylinder, open chamber diesel engine was converted to operate on homogenously charged compressed natural gas (CNG) with the aim of minimising pollutant emissions such as oxides of nitrogen, particulate matter and carbon dioxide. Three ignition systems were tested including spark ignition (SI), diesel pilot ignition (DPI) and hydrogen assisted jet ignition (HAJI). Irrespective of ignition system used, the efficiency of the engine operating on CNG was significantly reduced at part load compared to diesel. This was predominantly due to a greater amount of unburnt hydrocarbons, higher cycle-by-cycle variability, slow and partial burns and increased heat transfer to the walls. DPI and HAJI systems were able to extend the lean limit to lambda 2.7 and 3.3 respectively, however this did not result in efficiency gains.

This paper presents a comparison of the influence of different mixture preparation strategies on gaseous fuel combustion in SI engines. Three mixture preparation strategies are presented for a dedicated LPG fuelled engine, showing varying results - gaseous phase port injection (PFI-G), liquid-phase port injection (PFI-L) and gaseous-phase throttle-body injection (TBI-G). Previous work by the authors has shown considerable differences in emissions and thermal efficiency between different fuelling strategies. This paper extends this work to the area of combustion characteristics and lean limit operation and closer analyses the differences between these systems. A dedicated LPG in-line six cylinder engine with compression ratio increased to 11.7:1 (up from the standard 9.65:1) was tested over a range of speed/torque conditions representing most of the steady-state parts of the Euro drive-cycle for light duty-vehicles. The air-fuel ratio was varied from lambda 1.0 to the lean limit.

Gas assisted jet ignition is a prechamber combustion initiation system for conventional spark ignition engines. With the system, a chemically active turbulent jet is used to initiate combustion in lean fuel mixtures enabling reliable combustion over a much broader range of air-fuel ratios. The extended range is due to the distributed ignition source provided by the jet, which can overcome the problems of poorly mixed main chamber charges and slower burning fuels. In addition, the ability to reliably ignite lean mixtures improves the thermal efficiency and enables ultra low emission levels. Experiments together with flame propagation modeling completed using STAR-CD with CHEMKIN Kinetics were done in order to examine the effects of numerous prechamber fuels on the ignition of the main fuel, which consisted of either liquefied petroleum gas (LPG) or gasoline.

In spark ignited engine maximum thermal efficiency is found with lean mixtures. The authors' models for optimizing engine design show a preference for burning at the lean limit which to date has been found from experimental measurements. Hence ignoring combustion variability in the modeling can cause significant error in engine performance and emissions at or close to the lean limit. To aid in optimizing engine design, a model is needed that allows the inclusion of variability in the search for lean operation solutions. Here a useful addition to modeling is presented - a physically based lean limit model that can allow the lean limit to be set as non-dimensional COV of IMEP or as a variance in IMEP. The current work focuses on predicting the increase of cyclic variability due to the dilution of the mixture, whether by EGR and residual gas or by excess air.

Favorable and unfavorable properties of hydrogen as a combustion engine fuel have been accommodated in a design of a fuel efficient and clean engine providing similar to gasoline maximum torque and power. The advanced H2ICE being developed is a turbocharged engine fitted with cryogenic port hydrogen fuel injection and the hydrogen assisted jet ignition (HAJI). The combustion chamber is designed to produce a high compression ratio and therefore high thermal efficiency. A waste gated turbocharger provides pressure boosting for an increased power density running ultra lean for SULEV operation without after treatment. Thanks to the combustion properties of hydrogen further enhanced by the HAJI system, the engine load is mainly controlled throttle-less decreasing the fuel-to-air equivalence ratio from ultra lean ϕ=0.43 to ultra-ultra lean ϕ=0.18. The computational model developed for addressing the major design issues and the predicted engine performance and efficiency maps are included.

There are two parts to achieving the optimization reported here. The development of an engine simulation model and an optimization algorithm. The engine performance is evaluated using a quasi-dimensional engine combustion model with sub models to incorporate friction, heat losses and abnormal combustion, that is knocking. After extensive search and development a new Particle Swarm Optimizer (PSO), has been developed. Optimization includes, for the first time, the search of discontinuous design variables. The input variables considered for this investigation are manifold air pressure, air-fuel ratio, spark timing, compression ratio, valve timing events including valve open duration, maximum valve lift and engine speed. This enables the identification of the maximum thermal efficiency at a given power output at any engine operating speed.