Search Results

The research of driver behavior characteristics has been a focus of vehicle handling and stability performance. With the driver preview effort, many different driver preview models of direction control have been proposed and the simulations of driver-vehicle-road closed-loop system made. But in the simulation, most of the conventional models have the same precondition that the road was simply described as a pre-given preview course. How to simulate the driver dynamically deciding vehicle preview course based on the real road circumstance is the key to the further research of the driver model. In this paper, a new driver direction control model is established, which is called the Optimal Preview Lateral Acceleration (OPLA) Model and divided into three sub-models: driver’s information identification model, driver’s fuzzy decision model of vehicle preview course and driver’s performance first-order correction model.

A generalized theoretical model of tire cornering properties is presented in steady state condition with lateral deflection of tread and complex deformation of carcass under consideration. The model is suitable for full range of vertical load and slip angle. Six parameters are defined to represent the characteristics of tire stiffness, contact pressure distribution and carcass deformation. The model is validated against test data. Some simplified models, e.g. brush model, HSRI model when longitudinal force is zero, Fiala model etc., can be derived as some specific cases of this model. The analytic model provides a sound foundation for semi-empirical expression and gains insight into study of vehicle system dynamics.

The objective of this study is to develop a non-steady & non-linear tire model for vehicle dynamic simulation and control for extreme lateral slip condition. This model is provided in a semi-analytical form based on the theoretical non-steady state model, presented at 2nd IAVSD Tyre Conference, Feb. 1997[6]. The tire model is based on a quasi-steady state concept, which generates the dynamic forces and moment according to the dynamic effective slip ratio cooperating with the Unified Semi-Empirical Tire Model for Steady State. Satisfying the theoretical boundary conditions at two sides (lowest & highest) in frequency domain, the tire model is capable of describing the transient force & moment characteristics of tires in higher frequency range, Comparing with the “Linear Approximation” model, presented at 4th AVEC Conference, Sept. 1998[4].

Vehicle dynamic control could improve vehicle performance. Vehicle stability is vital to the determination of vehicle dynamic control strategy. The phase plane method is one of the most common methods to judge vehicle stability. To determine the 4WS (four-wheel steering) vehicle stability status faster and more accurately, a novel method to assess the vehicle stability is based on the vehicle sideslip angle and angular velocity (β-β˙) phase plane. At first, the 2 DOF (degree of freedom) model with a nonlinear tire model is established to acquire β-β˙ phase plane. Then the boundary of the stability region generated by the current method is compared. A crosspoint-ellipse method is provided based on the boundary comparison with the ideal boundary. The boundary function determined by the crosspoint-ellipse method is fitted based on vehicle dynamic theory and the boundary analysis with different steering angles, velocity, and road adhesion coefficient.

Tire lag property is a basic property of tire dynamics, and it has significant influence on the performance of vehicle dynamics. In distance domain, the side force and moments produced by a massless tire are basically displacement or path frequency dependent, rather than time dependent. In the paper, on the basis of the stretched-string model, the first-order filtering of deflection for the front point of the contact print and the first-order filtering of side force have been introduced. Tire system can be regarded as a first-order linear system under small slip angle. The force response of tire has the characteristics of the responses of first-order linear system under small angle. The relaxation length is an important parameter in studying tire lag property. It decreases with increasing slip angle. It plays an important role in the study of tire transient properties.

Based on the tire cornering properties in steady state condition, a theoretical model of non-steady state tire cornering properties (NSSTCP) with small lateral inputs is presented. The outputs of the model are lateral force and aligning moment, while the inputs are yaw angle and lateral displacement (or turn slip and slip angle). The deformation characteristics of contact patch are analyzed in non-steady state condition. The flexibility of tread and that of carcass are both taken into account. The deformation of carcass is assumed to compose of translating part, bending part and twisting part. The tests of NSSTCP including pure yaw motion and pure lateral motion are realized with step inputs of yaw angle and slip angle respectively and test data is then transformed into frequency domain. The model is validated through comparing the computational results with test frequency response.

In this paper, on the basis of the extant semi-empirical tire models of non-steady state with pure yaw angle input and pure side slip angle input, two empirical tire models of non-steady state side slip properties are established, one is pure yaw angle input, the other is pure side slip angle input, and both of them have been verified by test data. These two models can be used to approximately express tire force within low frequency. They have their own advantages, and make up for the disadvantages of existing tire models. They provide more choice for the simulation of vehicle dynamics.

Non-steady state (NSS) tire cornering properties show obvious differences from steady state (SS) tire cornering properties. A two-DOF automobile model with steer angle as an input is established based on the known NSS tire model considering complex carcass deformation. The tire model can certainly be applied to modelling of a multi-DOF automobile system. The frequency responses of lateral acceleration and yaw rate are then derived. An evaluation index, amplitude-frequency characteristic of relative error (AFCRE), is used to analyze the influences of NSS front wheels (FW) and/or rear wheels (RW) on automotive handling. The influences of NSS FW are much greater than those of NSS RW only on automotive handling. The established automobile model can also be applied to other similar studies of vehicle dynamics.

Vehicle handling and stability performances are greatly determined by non-steady state (NSS) tire cornering properties. Analytical derivation of NSS tire cornering models are presented in this paper based on Pacejka's string-concept assumption, in which carcass is assumed to be a stretched string with lateral deformation and lateral relaxation. The lateral inputs of the models are either displacement-based (lateral displacement and yaw angle) or slip-based (slip angle and turn slip). The transient deformations in spatial domain in both longitudinal and lateral directions are obtained directly from geometric relationship of contact patch. The additional self-aligning moment due to longitudinal deformation of contact patch after effect of tire width is considered is also achieved according to geometric relationship of contact patch in longitudinal direction and two transient geometric conditions of contact point.

The STI (System Technology Inc.) tire model is one of the most important semi-empirical (steady-state) tire models currently applied in the vehicle dynamics simulation software package of the National Advanced Driving Simulator (NADS). The STI tire model is presented originally based on tire contact length directly and the contact length is required to provide. Based on the concepts of nominal slip in both longitudinal and lateral directions, the STI tire model is analyzed and rewritten. It shows that the STI tire model does not actually depend on the contact length. Meanwhile, the model parameters are partially assigned new physical definitions, for example, static/dynamic stiffness and shape factors. Some simplified expressions are given based on further assumption conditions. The simplified expressions are also obtained regarding longitudinal slip at arbitrary speeds (including low speed, zero speed and stand still), which is originally presented by Bernard.

All the frictional forces developed from tire-snow interfaces are closely associated with snow depth and snow sinkage. One of the important differences between tire-soil interaction and tire-snow interaction is that the latter is explicitly snow depth dependent. Based on our established depth-dependent upper bound indentation model, the effects of snow depth on tire-snow interaction are presented in this paper. Snow is considered as a pressure-sensitive Drucker-Prager material. The required snow material parameters of the model are Drucker-Prager material constants only. Snow sinkages, for longitudinal slip close to zero, under different snow depths are numerically solved through the sinkage solver. The comparison between sinkage obtained analytically and the sinkage computed from finite element simulation is very good.

In the paper, the Flat Plank Tire Tester of Changchun Automobile Institute is introduced. This paper, according to practical experiences, generalizes some issues in the tire's non-steady state test. In the non-steady state test, it must be assured that the footprint centerline of tire coincides with that of slid platform, which guarantees no sliding motion between tire and slid platform during the movement. Due to tire taper effect and inhomogeneous tire material, when its side slip angle is zero, side force and aligning torque are not zeros, but have initial values. Here two approaches are discussed to eliminate the side force and aligning torque. Besides, other factors in the test are put forward for discussion. Eliminating the interference can obviously improve the test accuracy. This paper also provides test curves of both pure side slip angle input and pure yaw angle input.

A novel predictable tire model has been proposed for combined braking and cornering forces, which is based on only a few pure baking and pure cornering tests. It avoids elaborate testing of all kinds of combinations of braking and side forces, which are always expensive and time consuming. It is especially important for truck or other large size tires due to the capability constraints of tire testing facilities for combined shear forces tests. In this paper, the predictive model is based on the concept of slip circle and state stiffness method. The slip circle concept has been used in the COMBINATOR model to obtain the magnitude of the resultant force under combined slip conditions; however the direction assumption used in the COMBINATOR is not suitable for anisotropic tire slip stiffness.

In this research, off-road vehicle simulation is performed with tire-soil interaction model. The predictive semi-analytical model, which is originally developed for tire-snow interaction model by Lee [4], is applied as a tire-soil interaction model and is implemented to MSC/ADAMS, commercial multi-body dynamic software. It is applied to simulate the handling maneuver of military vehicle HMMWV. Two cases are simulated with Michigan sandy loam soil property. Each case has two maneuvers, straight-line brake and step steer (J-turn). First, tire-soil interaction model and conventional on-road tire model are simulated on the flat road of the same frictional coefficient. The proposed tire-soil interaction model provided larger force under the same slip. Second, the same maneuvers are performed with real off-road frictional coefficient. The proposed tire-soil model can be validated and the behavior of the off-road vehicle can be identified through two simulation cases.

High-fidelity finite element (FE) tire-snow interaction models have the advantage of better understanding the physics of the tire-snow system. They can be used to develop semi-analytical models for vehicle design as well as to design and interpret field test results. For off-terrain conditions, there is a high level of uncertainties inherent in the system. The FE models are computationally intensive even when uncertainties of the system are not taken into account. On the other hand, field tests of tire-snow interaction are very costly. In this paper, dynamic metamodels are established to interpret interaction forces from FE simulation and to predict those forces by using part of the FE data as training data and part as validation data. Two metamodels are built based upon the Krieging principle: one has principal component analysis (PCA) taken into account and the other does not.

There is a scarcity of comprehensive tire-snow interaction models for combined (longitudinal and lateral) slips. Current tire-snow interaction empirical and finite element models mostly focus on force-slip relationships in the longitudinal direction only, following the approach used for tire-soil interaction models. One of the major differences between tire-snow and tire-soil interactions is that the former is typically depth-dependent, especially for shallow snow. Our approach in the modeling of tire-snow interaction is to rely on the underlying physics of the phenomena, wherever we could, and use test data (or finite element simulation results in the absence of test data) to calibrate the required model parameters. We also make contact with on-road models and extend them for off-road applications.

A closed-loop comprehensive evaluation and a test method for vehicle handling and stability have been studied by using development driving simulator. Simulator test scheme has been designed and carried out with 14 vehicle configurations, and subjective evaluation has been made for easy handling of vehicle by drivers. A closed-loop comprehensive evaluation index has been put forward considering the factors affecting vehicle handling and stability. The reliability of the index has been validated by driver's subjective evaluation. A driver/vehicle/ road closed-loop system model has been established, and the theoretical predictive evaluation has been carried out with 14 vehicle configurations. Simulation showed that similar result for both theoretical predictive evaluation and subjective evaluation.

Simulations of tire cornering properties with small-amplitude lateral inputs are carried out in non-steady state conditions. The simulation algorithm is derived and the discrete expressions are presented in detail. Based on the simulations, lateral force and aligning moment can be calculated numerically with time-varying yaw angle and lateral displacement as inputs in spatial domain. The flexibility of both tread and carcass along with tire width is taken into account effectively in the simulations, in which the flexibility of carcass includes translating, bending and twisting flexibility. The simulations in non-dimensional form are associated with four tire structure parameters only, which are non-dimensional parameters reflecting the characteristics of tire stiffness, tire width and contact length. Simulation results are validated by test data from step lateral inputs tests. Several typical simulation results are provided.

High-quality dynamics model is one of the trends of vehicle dynamics model research and development. The engine generates high frequency excitation during operation, which may cause dynamic response in full vehicle. However, the widely-used internal-combustion engine model in vehicle dynamics simulation is steady-state model, which can't describe the fluctuation of engine drive torque along with the crankshaft angle. Consequently, this article concentrates on the modeling of instantaneous engine drive torque in order to improve the dynamic performance of the vehicle model. The paper has built the quasi-instantaneous engine model based on indicator diagram. To satisfy the requirement of real-time simulation, dynamically equivalent piston-connecting rod model is built and fast interpolation algorithm is researched. The linkage was simplified to spring and damper, and decoupled the piston translation and the crank rotation movements.

With the development of computer and vehicle research to high frequency, the driving simulator plays an important role on vehicle research and pre-development. The driving simulator have already been used for research about human factors, advanced active system (ABS, ESP et al), the vehicle dynamics and intelligent transportation systems (ITS) et al. The crucial requirement for a driving simulator is that it should have realistic behavior. The realistic behavior base on high-fidelity dynamics models especially tire model. “Tire/road” model is of special importance model for its influence on vehicle performances. The forces for accelerating, braking and steering are all came from tire road contact. The simulator simulation faces all possible driving scenes as driving in the real word, like parking on the hill, stop and start again, sharp steering and sharp braking et al.