Search Results

Standard

Undervehicle Coupon Corrosion Tests

2016-04-05

CURRENT

J1293_201604

This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.

Standard

UNDERVEHICLE COUPON CORROSION TESTS

1990-01-01

HISTORICAL

J1293_199001

This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.

Standard

Testing Dynamic Properties of Elastomeric Isolators

1999-05-01

HISTORICAL

J1085_199905

These methods cover testing procedures for defining and specifying the dynamic characteristics of simple elastomers and simple fabricated elastomeric isolators used in vehicle components. Simple, here, is defined as solid (non-hydraulic) components tested at frequencies less than or equal to 25 Hz.

Standard

Testing Dynamic Properties of Elastomeric Isolators

2017-02-09

CURRENT

J1085_201702

These methods cover testing procedures for defining and specifying the dynamic characteristics of simple elastomers and simple fabricated elastomeric isolators used in vehicle components. Simple, here, is defined as solid (non-hydraulic) components tested at frequencies less than or equal to 25 Hz.

Standard

Technical Report on Low Cycle Fatigue Properties Ferrous and Non-Ferrous Materials

2002-08-13

HISTORICAL

J1099_200208

Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. Information presented here can be used in preliminary design estimates of fatigue life, the selection of materials and the analysis of service load and/or strain data. The data presented are for the “low cycle” or strain-controlled methods for predicting fatigue behavior. Note that these methods may not be appropriate for materials with internal defects, such as cast irons, which exhibit different tension and compression stress-strain behavior.

Standard

Strain-Life Fatigue Data File Format

2018-08-24

CURRENT

J2409_201808

SAE format for a SIMPLE Strain-Life Fatigue Data Exchange File Format. The object of this SAE Standard is to provide a simple common way to exchange strain-life fatigue data collected from ASTM E 606 axial fatigue test data.

Standard

Strain-Life Fatigue Data File Format

2018-08-24

CURRENT

J2649_201808

SAE data file format for exchanging controlled periodic overload data. The object of this SAE Standard is to provide a simple, common methodology for exchanging the data from periodic overload fatigue tests. These tests consist of a single large fatigue cycle followed by a larger number of smaller cycles. The overloads are fully reversed fatigue cycles while the smaller cycles share a common mean and amplitude.

Standard

Steering Ball Studs and Socket Assemblies

2012-10-15

CURRENT

J491_201210

This SAE Recommended Practice has been established for the purpose of providing design criteria and suggested dimensional proportions which may be used for ball studs and ball stud socket assemblies as used on steering systems or control mechanisms of passenger vehicles, trucks and off-road equipment. The recommended practice does not cover all applications. It is intended to provide assistance in obtaining functional satisfaction and interchangeability. The inclusion of dimensional data in this report is not intended to imply that all the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning stock production parts.

Standard

Standard Rainflow File Format

2018-08-24

CURRENT

J2623_201808

This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.

Standard

Standard Rainflow File Format

2002-04-30

HISTORICAL

J2623_200204

This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.

Standard

Stainless Steel 17-7 PH Spring Wire and Springs

2016-04-05

CURRENT

J217_201604

This SAE Recommended Practice covers a high-quality corrosion-resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document also covers processing requirements of the springs and forms fabricated from this wire.

Standard

Softening Point of Interior Trim Adhesives

2021-01-07

CURRENT

J1700_202101

This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load.

Standard

Shaft Ends

2014-06-05

CURRENT

J501_201406

Standard

STAINLESS STEEL 17-7 PH SPRING WIRE AND SPRINGS

1994-07-01

HISTORICAL

J217_199407

This SAE Recommended Practice covers a high-quality corrosion-resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document also covers processing requirements of the springs and forms fabricated from this wire.

Standard

SOFTENING POINT OF INTERIOR TRIM ADHESIVES

1994-04-21

HISTORICAL

J1700_199404

This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load.

Standard

SHAFT ENDS

1948-05-01

HISTORICAL

J501_194805

Standard

Recommended Guidelines for Load/Deformation Testing of Elastomeric Components

2017-01-05

CURRENT

J1636_201701

The purpose of this SAE Recommended Practice is to review factors that influence the behavior of elastomeric components under conditions of loading or deforming at a constant rate and to provide guidance concerning test procedures used to define or specify the load/deformation characteristics of elastomeric components. This characteristic is referred to as Static Stiffness. This is also referred to as a "Static Deflection Test."

Standard

RECOMMENDED GUIDELINES FOR LOAD/DEFORMATION TESTING OF ELASTOMERIC COMPONENTS

1993-02-01

HISTORICAL

J1636_199302

The purpose of this SAE Recommended Practice is to review factors that influence the behavior of elastomeric components under conditions of loading or deforming at a constant rate and to provide guidance concerning test procedures used to define or specify the load/deformation characteristics of elastomeric components. This characteristic is referred to as Static Stiffness. This is also referred to as a "Static Deflection Test."

Standard

Prevention of Corrosion of Motor Vehicle Body and Chassis Components

2016-04-05

CURRENT

J447_201604

This SAE Information Report provides automotive engineers with the basic principles of corrosion, design guidelines to minimize corrosion, and a review of the various materials, treatments, and processes available to inhibit corrosion of both decorative and functional body and chassis components.

Standard

Peel Adhesion Test for Glass to Elastomeric Material for Automotive Glass Encapsulation

2021-01-07

CURRENT

J1907_202101

This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass. This test method suggests that elastomeric material of less than 172 mpa modulus be used as the encapsulating material. The present practice of encapsulating automotive glass is described as molded-in-place elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with the cured elastomeric material bonded to the perimeter of the glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.