Search Results

Standard

WIRING COMPONENT DESIGN GUIDELINES

2009-07-10

HISTORICAL

USCAR12-3

This document gives general guidelines to be used during the connector design stage. Various guidelines may not apply in all situations. Therefore, sound engineering judgment must be used in their application. Consider these guidelines as the basis for connector and wiring DFMEA’s. Items in this document are grouped by DFMEA functional requirements. Groups are as follows: A Electrical Continuity B Electrical Isolation/Sealing C Device Assembly D Harness Assembly E Vehicle Assembly F Materials G Serviceability H Environmental Requirements I High Voltage (≥ 60V) Application Requirements

Standard

WIRING COMPONENT DESIGN GUIDELINES

1999-07-01

HISTORICAL

USCAR12

This document gives general guidelines to be used during the connector design stage. Various guidelines may not apply in all situations. Therefore, sound engineering judgment must be used in their application. Consider these guidelines as the basis for connector and wiring DFMEA’s. Items in this document are grouped by DFMEA functional requirements. Groups are as follows: A Non-functional Drawing Requirements B Electrical Continuity C Electrical Isolation/Sealing D Device Assembly E Harness Assembly F Vehicle Assembly G Serviceability

Standard

WIRING COMPONENT DESIGN GUIDELINES

2001-12-01

HISTORICAL

USCAR12-2

This document gives general guidelines to be used during the connector design stage. Various guidelines may not apply in all situations. Therefore, sound engineering judgment must be used in their application. Consider these guidelines as the basis for connector and wiring DFMEA’s. Items in this document are grouped by DFMEA functional requirements. Groups are as follows: A Non-functional Drawing Requirements B Electrical Continuity C Electrical Isolation/Sealing D Device Assembly E Harness Assembly F Vehicle Assembly G Serviceability

Standard

Torque-Tension Testing and Evaluation of Fastener Finishes

1998-12-30

HISTORICAL

USCAR11

This standard provides a test method for determining the torque-tension relationship of a fastener finish as applied to a surrogate screw for the purpose of measuring the frictional characteristic of the fastener finish. The results obtained by this test shall be used as a process control attribute of the fastener finish and shall not be utilized for specific applications.

Standard

TORQUE-TENSION TESTING AND EVALUATION OF FASTENER FINISHES

2020-11-19

CURRENT

USCAR11-2

This standard provides a test method for determining the torque-tension relationship of a fastener finish as applied to a surrogate screw for the purpose of measuring the frictional characteristic of the fastener finish. The results obtained by this test shall be used as a process control attribute of the fastener finish and shall not be utilized for specific applications.

Standard

TORQUE-TENSION TESTING AND EVALUATION OF FASTENER FINISHES

2007-03-01

HISTORICAL

USCAR11-1

This standard provides a test method for determining the torque-tension relationship of a fastener finish as applied to a surrogate screw for the purpose of measuring the frictional characteristic of the fastener finish. The results obtained by this test shall be used as a process control attribute of the fastener finish and shall not be utilized for specific applications.

Standard

Standard for Cigar Lighters & Power Outlets

2014-03-31

CURRENT

USCAR4-1

This standard is intended to cover cigar or cigarette lighters as well as power outlets based on the form and dimensions of the cigar lighter. This standard is a full performance specification, it includes dimensional and operational parameters as well as performance characteristics which must be met when submitting a cigar lighter assembly or power outlet assembly for production approval. This standard constitutes an acceptance specification for a surface mounted, front-loaded cigar lighter or power outlet.

Standard

Specification for Testing Automotive Light Bulb Sockets

2006-08-08

HISTORICAL

USCAR15-2

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connector, direct wire wedge base sockets, circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendix E whenever the following occurs: New design Design, material or process change made to an existing device, which could affect the outcome of the test. The test sequence shown in Appendix F shall be run annually. (Note: Production process control data collected at a shorter interval per an approved control plan, may be substituted if approved by customer’s responsible engineer and purchasing representative.)

Standard

Specification For Testing Automotive Miniature Bulb Socket/Circuit Plate Assemblies

2004-01-30

HISTORICAL

USCAR15

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connector, direct wire wedge base sockets, circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendix E whenever the following occurs: New design Design, material or process change made to an existing device, which could affect the outcome of the test. Tests marked ‘Yearly’ in the following Test Schedule Table shall be run annually. Each test shall be run on 10 samples minimum; tests may be grouped, as supplier prefers, to reduce sample quantity or facilitate scheduling. Production process control data collected at a shorter interval per an approved control plan, may substituted if approved by customer’s responsible engineer and purchasing representative.

Standard

Specification For Testing Automotive Miniature Bulb Socket/Circuit Plate Assemblies

2004-12-10

HISTORICAL

USCAR15-1

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connector, direct wire wedge base sockets, circuit plate assemblies, and associated interfaces. Tests shall follow the sequence shown in the flow charts in Appendix E whenever the following occurs: New design Design, material or process change made to an existing device, which could affect the outcome of the test. The following test sequences shall be run annually: Test Sequence #2 (Run only the tests listed below, in the following order.) ○ Bulb Insertion/Removal Force ○ Voltage Drop ○ Vibration ○ Bulb Insertion/Removal Force ○ Bulb Wobble Test Sequence #8 Test Sequence #9 Test Sequence #10

Standard

STANDARD FOR D.C. BRUSH MOTOR – HVAC BLOWERS

1999-02-01

HISTORICAL

USCAR6

This standard sets forth the performance and durability requirements for 12-volt, D.C. brush-type electric motors used for automobile Heating, Ventilation, and Air Conditioning (HVAC) blowers and outlines Production Validation and Continuing Conformance testing.

Standard

STANDARD FOR CIGAR LIGHTERS & POWER OUTLETS

1998-09-01

HISTORICAL

USCAR4

This standard is intended to cover cigar or cigarette lighters as well as power outlets based on the form and dimensions of the cigar lighter. This standard is a full performance specification, it includes dimensional and operational parameters as well as performance characteristics which must be met when submitting a cigar lighter assembly or power outlet assembly for production approval. This standard constitutes an acceptance specification for a surface mounted, front-loaded cigar lighter or power outlet.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE MINIATURE BULBS

2022-03-15

CURRENT

USCAR3-4

The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications. The following tests shall be run whenever the following occurs: New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test. The completion of one calendar year as noted in the following Test Schedule Table. Process control data is acceptable.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE LAMP ASSEMBLIES

2022-03-15

CURRENT

USCAR34

The procedures contained in this specification cover the laboratory testing of Exterior Lamps for use in automotive road illumination. The following tests are intended to be run under the following conditions. This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards. If other manufacture’s components are intended to be approved for use in the lamp assembly, then those possible combinations of components shall be considered a new lamp assembly and shall also be tested.

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE HALOGEN LIGHT SOURCES

2022-03-15

CURRENT

USCAR14-3

The procedures contained in this specification cover the laboratory testing of replaceable halogen incandescent bulbs for use in automotive road illumination. The following tests are intended to be run under the following conditions. New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test The completion of one calendar year, accept as noted in the following Test Schedule Table. Test Title Yearly Physical Dimensions X Mean Spherical Candela (MSCD) X External Visual Examination X Color X Leak/Sealability Through Terminals and Seals X Deflection X Fluid Compatibility Terminal Retention X Resonant Frequencies Aged Resonant Frequency Salt Spray Outgassing Temperatures Requirement Laboratory Life at 14.0 VDC X Luminous Intensity Maintenance X Vibration Durability Shock Aged Vibration Durability Terminal Requirements DRL (SAE J2087)

Standard

SPECIFICATION FOR TESTING AUTOMOTIVE HALOGEN LIGHT SOURCES

2002-04-15

HISTORICAL

USCAR14-1

The procedures contained in this specification cover the laboratory testing of replaceable halogen incandescent bulbs for use in automotive road illumination. The following tests are intended to be run under the following conditions. New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test The completion of one calendar year, accept as noted in the following Test Schedule Table. Test Title Yearly Physical Dimensions X Mean Spherical Candela (MSCD) X External Visual Examination X Color X Leak /Sealability Through Terminals and Seals X Deflection X Fluid Compatibility Terminal Retention X Resonant Frequencies Aged Resonant Frequency Salt Spray Outgassing Temperatures Requirement Laboratory Life at 14.0 VDC X Luminous Intensity Maintenance Vibration Durability Shock Aged Vibration Durability Terminal Requirements DRL (SAE J2087)

Standard

ROAD VEHICLES – 60 V AND 600 V SINGLE CORE (ISO/METRIC) CABLES – DIMENSIONS, TEST METHODS AND REQUIREMENTS

2017-07-13

CURRENT

USCAR23-1

This International Standard specifies the dimensions, test methods, and requirements for single core 60 V cables intended for use in road vehicle applications where the nominal system voltage is ≤ (60 V DC or 25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is > (60 V DC or 25 V AC) to ≤ (600 V DC or 600 V AC). It also applies to individual cores in multi-core cables. See ISO 6722 for “Temperature Class Ratings”.

Standard

ROAD VEHICLES – 60 V AND 600 V SINGLE CORE (ISO/METRIC) CABLES – DIMENSIONS, TEST METHODS AND REQUIREMENTS

2002-09-09

HISTORICAL

USCAR23

This International Standard specifies the dimensions, test methods, and requirements for single core 60 V cables intended for use in road vehicle applications where the nominal system voltage is ≤ (60 V DC or 25 V AC). It also specifies additional test methods and/or requirements for 600 V cables intended for use in road vehicle applications where the nominal system voltage is > (60 V DC or 25 V AC) to ≤ (600 V DC or 600 V AC). It also applies to individual cores in multi-core cables. See ISO 6722 for “Temperature Class Ratings”.

Standard

Performance Specification for Ultrasonically Welded Wire/Cable Termination

2009-12-18

HISTORICAL

USCAR38

IMPORTANT NOTICE: In any intended vehicle application, if the products covered by this specification are, or may be, subjected to conditions beyond those described in this document, they must pass special tests simulating the actual conditions to be encountered before they can be considered acceptable for actual vehicle application. Products certified by their supplier as having passed specific applicable portions of this specification are not to be used in applications where conditions may exceed those for which the product has been satisfactorily tested. The Authorized Person is the final authority as to what tests are to be performed on his or her parts and for what purpose these tests are required. He or she is also the final authority for resolving any questions related to testing to this specification and to authorizing any deviations to the equipment or procedures contained in this specification.

Standard

Performance Specification for Automotive RF Connector Systems

2004-11-30

HISTORICAL

USCAR17-2