Search Results

Abstract An investigation into the pre-ashing of new gasoline particulate filters (GPFs) has demonstrated that the filtration efficiency of such filters can be improved by up to 30% (absolute efficiency improvement) when preconditioned using ash derived from a fuel-borne catalyst (FBC) additive. The additive is typically used in diesel applications to enable diesel particulate filter (DPF) regeneration and can be added directly into the fuel tank of the vehicle. This novel result was compared with ash derived from lube oil componentry, which has previously been shown to improve filtration efficiency in GPFs. The lube oil-derived ash utilized in this work improved the filtration efficiency of the GPF by −30%, comparable to the ash derived from the FBC additive.

Abstract Dynamic stresses exist in parts of a catalyst muffler caused by the vibration of a moving vehicle, and it is important to clarify and predict the vibration response properties for preventing fatigue failures. Assuming a vibration isolating installation in the vehicle frame, the vibration transmissibility and local dynamic stress of the catalyst muffler were examined through a vibration machine. Based on the measured data and by systematically taking vibration theories into consideration, a new prediction method of the vibration modes and parameters was proposed that takes account of vibration isolating and damping. A lumped vibration model with the six-element and one mass point was set up, and the vibration response parameters were analyzed accurately from equations of motion. In the vibration test, resonance peaks from the hanging bracket, rubber bush, and muffler parts were confirmed in three excitation drives, and local stress peaks were coordinate with them as well.

Abstract Gasoline Particulate Filter (GPF) technology is the key method of meeting the new regulations for particulate matter emissions from gasoline cars. Computer-Aided Engineering is widely used for the design of such systems; thus the development of accurate models for GPFs is crucial. Most existing pressure loss models require experimental calibration of several parameters. These experiments are performed at room temperatures, or on an engine test bench, where gas properties cannot be fully controlled. This article presents pressure loss measurements for clean GPF cores performed with uniform airflow and temperatures up to 680°C. The flow regime in GPF is shown to be different to that in the Diesel Particulate Filters (DPF) due to high flow rates and temperatures. Therefore, most of the existing models are not suitable for design of the new generation of aftertreatment devices. To separate pressure loss contribution from different sources, unplugged filter cores are tested.

Abstract The wide application of Gasoline Direct Injection (GDI) engines and the increasingly stringent Particulate Matter (PM) and Particulate Number (PN) regulations make Gasoline Particulate Filters (GPFs) with high filtration efficiency and low pressure drop highly desirable. However, due to the specifics of GDI operation and GDI PM, the design of these filters is even more challenging as compared to their diesel counterparts. Computational Fluid Dynamics (CFD) studies have been shown to be an effective way to investigate filter performance. In particular, our previous two-dimensional (2D) CFD study explicated the pore size and pore-size distribution effects on GPF filtration efficiency and pressure drop. The “throat unit collector” model developed in this study furthers this work in order to characterize the GPF wall microstructure more precisely.

Abstract Diesel engines include systems for cooling, lubrication, and fuel injection and contain a variety of components. A malfunction in any of the engine systems or the presence of any faulty element influences engine performance and deteriorates its components. This research is concerned with the untimely appearance of vital cracks in the liners of a turbocharged heavy-duty Diesel engine. To find the root causes for premature failure, rigorous examinations through visual observations, material characterization, and metallographic investigations are performed. These include Scanning Electron Microscope (SEM) and Energy-Dispersive Spectroscopy (EDS), fracture mechanics analysis, and performance examination, which are also followed by Finite Element Moldings. To find the proper remedy to resolve the problem, drawing a precise and reliable picture of the engine’s operating conditions is required.

Abstract The frequency of video-capturing collision events from surveillance systems are increasing in reconstruction analyses. The video that has been provided to the investigator may not always include a clear perspective of the relevant area of interest. For example, surveillance video of an incident may have captured a pre- or post-incident perspective that, while failing to capture the precise moment when the pedestrian was struck by a vehicle, still contains valuable information that can be used to assist in reconstructing the incident. When surveillance video is received, a quick and efficient technique to place the subject object or objects into a three-dimensional environment with a known rate of error would add value to the investigation.

Abstract The article describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components’ light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features has been thoroughly experimentally examined.

Abstract Different aftertreatment systems consisting of a combination of selective catalytic reduction (SCR) and SCR catalyst on a diesel particulate filter (DPF) (SCR-F) are being developed to meet future oxides of nitrogen (NOx) emissions standards being set by the Environmental Protection Agency (EPA) and the California Air Resources Board (CARB). One such system consisting of a SCRF® with a downstream SCR was used in this research to determine the system NOx reduction performance using experimental data from a 2013 Cummins 6.7L ISB diesel engine and model data. The contribution of the three SCR reactions on NOx reduction performance in the SCR-F and the SCR was determined based on the modeling work. The performance of a SCR was simulated with a one-dimensional (1D) SCR model. A NO2/NOx ratio of 0.5 was found to be optimum for maximizing the NOx reduction and minimizing NH3 slip for the SCR for a given value of ammonia-to-NOx ratio (ANR).

Abstract The causes of failure due to cracking in the resistance spot welding of the advanced high-strength steels dual-phase 590 (DP590) were investigated using scanning electron microscopy (SEM), optical microscopy, and the tensile-shear test. The results showed that by increasing the current amount, the formation of the melting zone occurred in the heat-affected zone, leading to the cracking in this area, reducing the tensile strength and decreasing the mechanical properties; the initiation and growth of cracking and failure in this region also happened. In the heat-affected zone, by increasing the current amount with the softening phenomenon, the recrystallized coarse grains also occurred, eventually resulting in the loss of mechanical properties. The results of the tensile-shear test also indicated that by increasing the current up to 12 kA, the strength was raised, but the ductility was reduced.

Abstract This study implements Flame Image Velocimetry (FIV), a diagnostic technique based on post-processing of high-speed soot luminosity images, to show the in-flame flow field development impacted by after-injection in a single-cylinder, small-bore optical diesel engine. Two after-injection cases with different dwell times between the main injection and after-injection, namely, close-coupled and long-dwell, as well as a main-injection-only case are compared regarding flow fields, flow vector magnitude, and turbulence intensity distribution. For each case, high-speed soot luminosity movies from 100 individual combustion cycles are recorded at a high frame rate of 45 kHz for FIV processing. The Reynolds decomposition using a spatial filtering method is applied to the obtained flow vectors so that bulk flow structures and turbulence intensity distributions can be discussed.

Abstract TOC

Abstract Although tread block deformation analysis is important, the deformation measurement is difficult because fast-rotating tires maintain a continuous contact with the road surface. Furthermore, capturing small displacements near the edge of tread blocks using a high-speed camera is difficult because of the particularly limited resolution. Additionally, the tread blocks being significantly deformed at the edge and susceptible to wear powder, the state change of the feature points, is highly probable. To overcome these problems, a system that obtains high-resolution images and measures the deformation of a fast-rotating body (tire) is proposed herein. The developed system captures the deformation behavior through intermittent imaging. To further measure the strain distribution, fine tracking markers are drawn on the tread block using a laser processing machine. The displacement of the marker is calculated using the particle mask correlation method.

Abstract An ongoing challenge with Gasoline engines is achieving rapid activation of the three-way catalyst during cold starts in order to minimize pollutant emissions. Retarded combustion is an effective way in achieving rapid light-up of the three-way catalyst and can be facilitated by stratified charge using late fuel injection. This, however, provides insufficient time for fuel entrainment with air, resulting in locally fuel-rich diffusion combustion. Employing a split injection strategy can help tackle these issues. The effects of a split injection strategy, using a high-pressure Solenoid injector, on the in-cylinder charge formation are investigated in the current study. The studies are performed inside an optical Gasoline engine using high-speed particle image velocimetry (PIV) in the central tumble and Omega tumble planes, by means of a high-speed laser and camera operating at a repetition rate of 10 kHz.

Abstract This research involves the study of the different properties of aluminum alloy (AA) 2024 in the presence of carbon nanotubes (CNTs) and Silicon (Si) nanoparticles. Structural morphology, elemental composition, mechanical properties (density, tensile strength, elongation, and hardness), and tribological properties (wear rate and coefficient of friction) of AA 2024 in the presence of CNTs, Si, and its combinations at various proportions were evaluated using a Scanning Electron Microscope (SEM), Energy Dispersive X-Ray Analyzer (EDX), Universal Testing Machine (UTM), Model HMV-2T Vickers hardness test machine, and pin-on-disk friction-and-wear test rig. The Hybrid Metal Matrix Composite (HMMC) material is prepared by a two-stage stir casting method. It was found that the density of the AA 2024 + 4%CNT + 2%Si is 2.22 g/cm3, ultimate tensile strength is 308 N/mm2, elongation is 15.5%, and Vickers hardness is 187.5 Vickers Hardness Number (VHN).

Abstract Reliable detection of obstacles around an autonomous vehicle is essential to avoid potential collision and ensure safe driving. However, a vast majority of existing systems are mainly focused on detecting large obstacles such as vehicles, pedestrians, and so on. Detection of small obstacles such as road debris, which pose a serious potential threat are often overlooked. In this article, a novel stereo vision-based road debris detection algorithm is proposed that detects debris on the road surfaces and estimates their height accurately. Moreover, a collision warning system that could warn the driver of an imminent crash by using 3D information of detected debris has been studied.

Abstract High fuel injection pressure systems for Gasoline Direct Injection (GDI) engines have become widely used in passenger car engines to reduce emissions of particulates and pollutant gases. Current commercial systems operate at pressures of up to 450 bar, but several studies have examined the use of injection pressures above 600 bar, and some have even used pressures around 1500 bar. These works revealed that high injection pressures have numerous benefits including reduced particulate emissions, but there is still a need for more data on the possible benefits of injection pressures above 1000 bar. This article presents spray and engine data from a comprehensive study using several measurement techniques in a spray chamber and optical and metal engines. Shadowgraph imaging and Phase Doppler Interferometry (PDI) were used in a constant volume chamber to interpret spray behavior. Particle Image Velocimetry (PIV) was used to capture near-nozzle air entrainment.

Abstract Today, as the spread of vehicles equipped with autonomous driving functions increases, accidents caused by autonomous vehicles are also increasing. Therefore, issues regarding safety and reliability of autonomous vehicles are emerging. Various studies have been conducted to secure the safety and reliability of autonomous vehicles, and the application of the International Organization for Standardization (ISO) 26262 standard for safety and reliability improvement and the importance of verifying the safety of autonomous vehicles are increasing. Recently, Mobileye proposed an RSS model called Responsibility Sensitive Safety, which is a mathematical model that presents the standardization of safety guarantees of the minimum requirements that all autonomous vehicles must meet. In this article, the RSS model that ensures safety and reliability was derived to be suitable for variable focus function cameras that can cover the cognitive regions of radar and lidar with a single camera.

Abstract In this work, we present a lightweight pipeline for robust behavioral cloning of a human driver using end-to-end imitation learning. The proposed pipeline was employed to train and deploy three distinct driving behavior models onto a simulated vehicle. The training phase comprised of data collection, balancing, augmentation, preprocessing, and training a neural network, following which the trained model was deployed onto the ego vehicle to predict steering commands based on the feed from an onboard camera. A novel coupled control law was formulated to generate longitudinal control commands on the go based on the predicted steering angle and other parameters such as the actual speed of the ego vehicle and the prescribed constraints for speed and steering. We analyzed the computational efficiency of the pipeline and evaluated the robustness of the trained models through exhaustive experimentation during the deployment phase.

Abstract Nitrous oxide (N2O) is both an ozone depleting gas and a potent greenhouse gas (GHG), having a global warming potential (GWP) value nearly 300 times that of carbon dioxide (CO2). While long known to be a trace by-product of combustion, N2O was not considered a pollutant of concern until the introduction of the three-way catalyst (TWC) on light-duty gasoline vehicles in the 1980s. These precious metal-containing catalysts were found to increase N2O emissions substantially. Through extensive research efforts, the effects of catalyst type, temperature, air/fuel ratio, space velocity, and other factors upon N2O emissions became better understood. Although not well documented, N2O emissions from non-catalyst vehicles probably averaged 5-10 mg/mi (on the standard FTP test), while early generation TWC-equipped vehicles exceeded 100 mg/mi. As emissions control systems evolved to meet increasingly stringent criteria pollutant standards, N2O emissions also decreased.

Abstract A major reduction of greenhouse gas emissions, as well as other toxic emissions, is required to reduce the environmental impact of transportation systems. Renewable fuels, in combination with new internal combustion processes, such as reactivity controlled compression ignition (RCCI), are promising measures to enable this reduction. By combining two fuels with different reactivity, RCCI offers high efficiency and low emissions through homogeneous low-temperature combustion. However, a two-fuel RCCI approach leads to an increased number of adjustable operation parameters, such as injection timing. Optimizing these operation parameters to ensure homogenous combustion is challenging. To that end, optical methods provide temporally and spatially resolved information on mixture formation and combustion to analyze the homogeneity of the process. However, established methods, such as OH* imaging, cannot differentiate between multiple fuels.