Search Results

Abstract Energy management strategies for charge-sustaining hybrid electric vehicles reduce fuel consumption and maintain battery pack state of charge while meeting driver output power demand. The equivalent consumption minimization strategy is a real-time energy management strategy that makes use of an equivalence ratio to quantify electric power consumption in terms of fuel power consumption. The magnitude of the equivalence ratio determines the hybrid electric vehicle mode of operation and influences the ability of the energy management strategy to reduce fuel consumption as well as maintain the battery pack state of charge. The equivalent consumption minimization strategy in this article uses three Willans line models, which have an associated marginal efficiency and constant offset, to model the performance in the hybrid electric vehicle controller.

Abstract To reduce fuel consumption and carbon dioxide (CO2) emissions from mobile air conditioning (A/C) systems, “U.S. Light-Duty Vehicle Greenhouse Gas Emissions and Corporate Average Fuel Economy Standards” identified solar/thermal technologies such as solar control glazings, solar reflective paint, and active and passive cabin ventilation in an off-cycle credit menu. National Renewable Energy Laboratory (NREL) researchers developed a sophisticated analysis process to calculate U.S. light-duty A/C fuel use that was used to assess the impact of these technologies, leveraging thermal and vehicle simulation analysis tools developed under previous U.S. Department of Energy projects. Representative U.S. light-duty driving behaviors and weighting factors including time-of-day of travel, trip duration, and time between trips were characterized and integrated into the analysis.

Abstract Autonomy and connectivity are considered among the most promising technologies to improve safety and mobility and reduce fuel consumption and travel delay in transportation systems. In this paper, we devise an optimal control-based trajectory planning model that can provide safe and efficient trajectories for the subject vehicle while incorporating platoon formation and lane-changing decisions. We embed this trajectory planning model in a simulation framework to quantify its fuel efficiency and travel time reduction benefits for the subject vehicle in a dynamic traffic environment. Specifically, we compare and analyze the statistical performance of different controller designs in which lane changing or platooning may be enabled, under different values of time (VoTs) for travelers.

Abstract Wheel loaders are widely used in construction projects. In order to reduce pollution and energy consumption, major wheel loader manufacturers are developing electric powertrain technology. Our main research goal is to reduce the energy consumption of a pure electric loader. This study is intended to build a vehicle simulation model of a multiple drive motor electric loader. According to the common working conditions and empirical formulas of the loader, the simulation data of the electric loader are calculated. The torque distribution control strategy based on the optimal efficiency of the motor is designed for the multiple drive motor electric loader and is compared with the equal proportion distribution control and the axle load ratio distribution control through simulation analysis. The simulation results show that the proposed torque distribution control strategy based on motor optimal efficiency can reduce energy consumption by 7–12%.

Abstract Uncertainty of fuel reserves, environmental crisis, and health concerns arise from transport demands and reliance on fossil fuels. Downsized gasoline turbocharged direct injection (GTDI) engines have been developed and applied to most modern gasoline vehicles, delivering superior efficiency in high-load operation, reduced friction, and weight. But fuel enrichment and late combustion phasing to mitigate knocking combustion have hindered the efficiency benefits at higher loads with high boost. Furthermore, the wide valve-overlap with a three-cylinder setup for the maximum scavenging efficiency produces bursts of short-circuit (SC) air to cause underestimation of the equivalence ratio by the oxygen sensor, resulting in higher tailpipe nitrogen oxides (NOx) emissions with three-way catalyst (TWC) exhaust aftertreatment. Reducing the valve overlap to limit short-circuiting and enrichment will recover the combustion efficiency and the engine ER, but at the cost of high knock onset.

Abstract The increase in worldwide awareness of environmental issues has necessitated the air transport industry to drastically reduce carbon dioxide emissions. To meet this goal, one solution is the electrification of aircraft propulsion systems. In particular, single-aisle aircraft with partial turboelectric propulsion with approximately 150 passenger seats in the 2030s are the focus. To develop a single-aisle aircraft with partial turboelectric propulsion, an air-cooled interior permanent magnet (IPM) motor with an output of 2 MW is desired. In this article, mathematical system equations that describe heat transfer inside the target air-cooled IPM motor are formulated, and their mathematical analytical solutions are obtained.

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract Numerous works have been carried out with perspectives to improve the energy efficiency of electric vehicle (EV) drivetrains; much of the attention has been on the design of highly efficient electric motors, power converters, and energy storage system. Besides the abovementioned factors, selection of the drivetrain configuration and control strategy also influence the efficiency and performance of EV drivetrain. The drivetrain efficiency and performance indices, such as torque ripple and total harmonic distortion (THD) of voltage and current, are sensitive to the direct current (dc)-link voltage and flux linkage values for a drivetrain control strategy. Therefore, in this work, the efficiency and the performance of two popular direct torque controlled induction motor (IM) drives are compared on the basis of adjustable dc-link voltage and flux linkage values for desired operating condition. Both these techniques are implemented on a lab scale test bed.

Abstract This study proposes a real-time control for plug-in hybrid electric vehicles (PHEVs) based on dynamic programming (DP). In order to obtain the optimal controls, DP is first used to solve the driving cycle, and a model-based calibration (MBC) tool is used to generate the optimal maps from the optimal trajectories. Further, a feedback energy management system (FEMS) is developed with the SoC as the feedback variable, which considers the charge and discharge reaction of the battery. To make full use of the energy stored in the battery, combined with the charge depletion-charge sustain (CDCS) strategy, the reference SoC is introduced. Finally, comparative simulation of the proposed real-time controller and DP is performed. The obtained results show that the fuel consumption of the real-time controller is 4.82 L/100 km in the worldwide harmonized light-duty vehicles’ test cycles, which is close to the fuel consumption with DP at 4.69 L/100 km.

Abstract Commercial vehicles require continual improvements in order to meet fuel consumption standards, improve diesel aftertreatment (AT) system performance, and optimize vehicle fuel economy. Simultaneous reductions in both CO2 and NOX emissions will be required to meet the upcoming regulatory targets for both EPA Phase 2 Greenhouse Gas Standards and new Low NOX Standards being proposed by the California Air Resources Board (CARB). In addition, CARB recently proposed a new certification cycle that will require high NOX conversion while vehicles are operating at lower loads than current regulatory cycles require. Cylinder deactivation (CDA) offers a powerful technology lever for meeting these two regulatory targets on commercial diesel engines. There have been numerous works in the past year showing the benefits of diesel CDA for elevating exhaust temperatures during low-load operation where it is normally too cold for AT to function at peak efficiency.

Abstract The airline industry faces a crisis in the future as consumer demand is increasing, but the environmental effects and depleting resources of kerosene mean that growth is unsustainable. Hydrogen is touted as the leading candidate to replace kerosene, but it needs significant technological and economical endeavors. In such a scenario, cryogenic liquid hydrogen (LH2) is predicted to be the most feasible method of using hydrogen. The major challenge of LH2 as an aircraft fuel is that it requires approximately four times the storage volume of kerosene—due to its lower density. Thus the design of cryogenic storage tanks to handle larger quantities of fuel is becoming increasingly important. But the increase in drag associated with larger storage tanks causes an increase in fuel consumption. Hence, this paper aims to evaluate the aerodynamic performance of different storage configurations and aid in the selection of an economic and efficient storage system.

Abstract This article concerns an improved vector control model. This model is developed in a phase which comes just before the phase of its integration on electronic boards such as those with FPGA or DSP. The innovative character of this model is based on the replacement of the average model of the Direct Current (DC) to Alternating Current (AC) converter powering a synchronous motor with permanent magnets by a precise model considering the transient model of the power transistors, electromagnetic switches, and diodes. The overall model generates the six DC-AC converter control signals to regulate the speed of the permanent magnet synchronous motor (PMSM) using the technique of back electromotive forces compensation to reduce the power chain energy consumption for variable rectilinear speed operation. This model makes it possible to consider the role of diodes.

Abstract The surge in economic activities, in the developing nations, has resulted in rapid expansion of urban centres. This expansion of cities has caused a rapid increase in vehicular traffic, which in turn has caused deterioration of air quality. To overcome the problem of unprecedented air pollution, the governments worldwide have framed policies for faster adoption of electric vehicles. One of the major challenges faced is the development of low- cost drive for these vehicles and keeping the imports to a minimum. As a result of this, the trend is to move away from the permanent magnet-based motor technology and to use induction motor-based drivetrain. For the induction motors to be successful in electric vehicle drivetrain application, it is important to have a robust speed control algorithm. This work aims at adapting a direct torque control technique for induction motor’s speed control.

Abstract This article investigates the ability of data-driven models to estimate instantaneous fuel consumption over 1 km road segments from different routes for different heavy-duty vehicles from the same fleet. Models are created using three different techniques: parametric, linear regression, and artificial neural networks. The proposed models use features derived from vehicle speed, mass, and road grade, which can be easily obtained from telematics devices, in addition to power take-off (PTO) active time, which is needed to capture the power requested by accessories in several heavy-duty vehicles. The robustness of these models with respect to the training data selection is improved by using k-fold cross-validation. Moreover, the inherent underestimation or overestimation bias of the model is calculated and used to offset the fuel consumption estimates for new routes. The study shows that the target application dictates the choice of model features.

Abstract The present work contributes to the development of a multimachine control structure in a traction chain of an all-wheel-drive electric vehicle (EV). In addition, in electric traction where the traction systems are propelled by several electric motors, it is necessary to optimize the devices’ volumes and the embedded components. Thus, an interesting reduction can be obtained by the use of a single inverter that supplies several motors simultaneously. An electric motor integrated into each wheel is one of the most common configurations in EVs, which allows an independent four-wheel drive. In this work, we are seeking to impose independent control on each wheel motor using a multimotor solution for the drivetrain architectures of an EV. An interior permanent-magnet synchronous motor (IPMSM) was chosen as a traction motor.

Abstract Federal Aviation Administration (FAA)’s 20 years of research and development with 200 unleaded blends and full-scale engine tests on 45 high-octane unleaded blends has not found a “drop-in” unleaded replacement for aviation gasoline (AVGAS) 100 low lead (100LL) fuel. In this study, analysis of compatibility via optimization of Lycoming O-320 engine fuelled with RON 97, RON 98, RON 100, and AVGAS was conducted using the Response Surface Methodology (RSM). Test fuels were compositionally characterized based on Gas Chromatography (GC) analysis and were categorized based on types of Hydrocarbon (HC). Basic fuel properties of fuels in this research were analyzed and recorded. For optimization analysis, engine speed and fuel were considered as the input parameters.