Search Results

Abstract The water droplet erosion (WDE) on high-speed rotating wheels appears in several engineering fields such as wind turbines, stationary steam turbines, fuel cell turbines, and turbochargers. The main reasons for this phenomenon are the high relative velocity difference between the colliding particles and the rotor, as well as the presence of inadequate material structure and surface parameters. One of the latest challenges in this area is the compressor wheels used in turbochargers, which has a speed up to 300,000 rpm and have typically been made of aluminum alloy for decades, to achieve the lowest possible rotor inertia. However, while in the past this component was only encountered with filtered air, nowadays, due to developments in compliance with tightening emission standards, various fluids also collide with the spinning blades, which can cause mechanical damage.

Abstract The importance of in-vehicle network security has increased with an increase in automated and connected vehicles. Hence, many attacks and countermeasures have been proposed to secure the controller area network (CAN), which is an existent in-vehicle network protocol. At the same time, new protocols-such as FlexRay and Ethernet-which are faster and more reliable than CAN have also been proposed. European OEMs have adopted FlexRay as a control network that can perform the fundamental functions of a vehicle. However, there are few studies regarding FlexRay security. In particular, studies on attacks against FlexRay are limited to theoretical studies or simulation-based experiments. Hence, the vulnerability of FlexRay is unclear. Understanding this vulnerability is necessary for the application of countermeasures and improving the security of future vehicles. In this article, we highlight the vulnerability of FlexRay found in the experiments conducted on a real FlexRay network.

Abstract This work introduces the concept of a dual-layer specification structure for standards that separate interoperability functions, such as backward compatibility, localization, and deployment, from those essential to reliability, security, and functionality. The latter group of features, which constitute the actual standard, make up the baseline layer for instructions, while all the elements required for interoperability are specified in a second layer, known as a Protocols, Operations, Usage, and Formats (POUF) document. We applied this technique in the development of a standard for Uptane [1], a security framework for over-the-air (OTA) software updates used in many automobiles. This standard is a good candidate for a dual-layer specification because it requires communication between entities, but does not require a specific format for this communication.

Abstract Current End-of-Life Vehicle (ELV) recycling processes are mainly based on mechanical separation techniques. These methods are designed to recycle those metals with the highest contribution in the vehicle weight such as steel, aluminum, and copper. However, a conventional vehicle uses around 50 different types of metals, some of them considered critical by the European Commission. The lack of specific recycling processes makes that these metals become downcycled in steel or aluminum or, in the worst case, end in landfills. With the aim to define several ecodesign recommendations from a raw material point of view, it is proposed to apply a thermodynamic methodology based on exergy analysis. This methodology uses an indicator called thermodynamic rarity to assess metal sustainability. It takes into account the quality of mineral commodities used in a vehicle as a function of their relative abundance in Nature and the energy intensity required to extract and process them.

Abstract Damage is accumulated by vehicles as they travel. Current damage methods allow for the total accumulated damage to be identified; however, they do not allow for identification of the road segments that induce the largest component of the damage. The objective of this article is to develop a measure, Localized Pseudo Damage (LPD), which defines the amount of damage each individual road excitation contributes to the total accumulated pseudo damage. A novel theoretical development of LPD along with analytical and discrete simulation analyses is presented. The results show that the LPD is causal and correctly identifies the location and magnitude of damaging events. This is further demonstrated with the application of the method on a real road surface.

Abstract Equal-channel angular pressing (ECAP) is among the most applicable severe plastic deformation processes used to fabricate ultrafine-grained materials with superior mechanical properties. In this work, a commercial purity aluminum has been processed via ECAP process up to four passes. The influence of ECAP routes (A and Bc) on the mechanical properties of the material and its grain size was investigated. Microstructural observations of the as-annealed and the rods processed via ECAP were undertaken using optical microscopy. Hardness profiles and contour maps of sections cut perpendicularly and parallel to the load direction were assessed to investigate the effect of ECAP processing on the hardness distribution across the deformed rods. Compressive properties of the rods were also examined. In addition, digital images correlation was used to display the stress distribution along the longitudinal section of the processed sample during the compression test.

Abstract The causes of failure due to cracking in the resistance spot welding of the advanced high-strength steels dual-phase 590 (DP590) were investigated using scanning electron microscopy (SEM), optical microscopy, and the tensile-shear test. The results showed that by increasing the current amount, the formation of the melting zone occurred in the heat-affected zone, leading to the cracking in this area, reducing the tensile strength and decreasing the mechanical properties; the initiation and growth of cracking and failure in this region also happened. In the heat-affected zone, by increasing the current amount with the softening phenomenon, the recrystallized coarse grains also occurred, eventually resulting in the loss of mechanical properties. The results of the tensile-shear test also indicated that by increasing the current up to 12 kA, the strength was raised, but the ductility was reduced.

Abstract The article considers one of the possible mechanisms of loading the solidity of a cylindrical metal composite high-pressure vessel (MC HPV). This mechanism manifests itself as delamination of a thin-walled metal shell (liner) from a more rigid composite shell causing local buckling. A similar effect can be detected in the manufacturing process of MC HPV, when the composite shell is formed by winding with tension a carbon fiber-reinforced plastic tape on the liner. Pressure transfer from the composite shell to the liner is carried out by the method of temperature analogy, that is, by cooling the composite shell, thermally insulated from the liner. To solve the problem of externally confined liner local buckling an approach is proposed, which is based on three points: the introduction of local technological deviations inherent in actual structures, the determination of the general stress-strain state, and a real-time deforming.

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract One of the most important aluminum (Al) alloys among the 7XXX series is 7075 in the T6 temper condition. However, 7075 T6 alloy is proven to be susceptible to stress corrosion cracking (SCC) and has caused many service failures of airplanes. In this research, the susceptibility of 7075 T6 alloys to SCC is approached according to many variables of stress, sodium chloride (NaCl) concentration, pH variation, and aeration. The testing method selected was the three-point bending under complete immersion for a period of 40 days. The results indicate that the threshold for SCC in 7075 T6 alloy lies between 220 and 340 MPa in environments containing as low as 0.5% NaCl concentrations in both neutral and acid solutions. The cracking direction found was different from the expected using other techniques such as tensile or notched specimens, which opens a new gate for testing and monitoring SCC in the 7XXX series.

Abstract The objective of the study was to evaluate the quasi-static and fatigue performance of automotive anti-roll bars (ARBs) under extreme environmental conditions. Flexural quasi-static and fatigue tests of SAE 1040 steel were conducted above and below the ductile-to-brittle transition temperature (DBTT) in flexure and compared with their room temperature performance. The flexural strength increased by decreasing the temperature to −40°C. The fatigue lives are determined for stress levels of 87%, 60%, and 30% of their flexural strength under displacement mode in constant amplitude loading. Experimental stress versus the number of cycles (S-N) curves of SAE 1040 steel state that all tube specimens have fatigue limits that were more than 100,000 cycles at −40°C. The fatigue life of the SAE 1040 tube exhibited infinite life below the ductile-to-brittle transition (DBT).

Abstract In this article, the quantitative relationship between the static stiffness, lightweight factor, and modal parameters of an aluminum space frame was investigated. Modal theory calculation and finite element method were employed in the analysis. Fifty modal parameters were extracted from the finite element model of the frame to calculate the bending stiffness, torsional stiffness, and lightweight factor of the frame. The deviations of the bending stiffness, torsional stiffness, and lightweight factor obtained from the modal theory and the finite element theory were found to be 0.91%, 1.72%, and 1.71%, respectively. It indicates that these two methods have similar accuracy. It was confirmed that the sum of each order modal compliance could be used to calculate the static compliance of the aluminum space frame. The first-order bending mode was found to be the corresponding mode order, which made the largest contribution to the bending stiffness.

Abstract In the present study, the mechanical performances of plain carbon steel were explored based on the grain growth behavior. In the first step, the samples were normalized at different temperatures ranging from 900°C to 1100°C for 30, 60, 100, 150, and 200 min, respectively. In order to measure the grain size, the planimetric technique of Jeffries was used based on the optical micrographs taken for each sample. The mechanical properties of each grain such as hardness, elongation, yield, and tensile strength were studied, depending on the conventional methods. Experimental results showed that the increase in both heating temperature and holding time enhances grain growth, while the growth rate decreases with increasing time. The initial grain size and proportionality constant were calculated at 950°C, where K = 2.26 μm2/min and D 0 = 25.09 μm. Moreover, a significant increase in strength and hardness was observed with a decrease in grain size.

Abstract In this article, Al-Mg-Si-Mn alloy (AA6082) is butt joined by employing friction stir welding (FSW). The mechanical and metallurgical properties of joints are analyzed by conducting tensile and microhardness testing, respectively. To measure the temperature at different locations, eight thermocouples (L-shaped k-type) are placed at equal distance from the centerline. Least square method attempts to calculate the temperature at the centerline of joints. The process parameters are also optimized using Taguchi’s five-level experimental design. The optimum process parameters are determined, employing ultimate tensile strength (UTS) as a response parameter. A statistical test “analysis of variance” is used to check the adequacy of the model. It has been observed that rotational speed and feed rate are the predominant factors for UTS and microhardness.

Abstract Tribological properties determine the elemental factors influencing the performance of the components that are subjected to relative motion. Of late, low-density Metal Matrix Composites (MMCs) have been renowned as materials for the components that are subjected to tribological applications. This work reports an experimental study of wear and corrosion behavior of Aluminum Metal Matrix Composites (AMMCs) reinforced with in situ TiB2 particles. These composites were synthesized by a mixed salt route procedure using K2TiF6 and KBF4 at a temperature of 850°C by using the stir casting method. Dry sliding wear behavior of AA5754-TiB2 in situ composites were compared with base material for the various loads, sliding speed, and sliding distances. These parameters were analyzed using Taguchi techniques. It was found that the percentage of reinforcement and load are the most significant parameters.

Abstract This research involves the study of the different properties of aluminum alloy (AA) 2024 in the presence of carbon nanotubes (CNTs) and Silicon (Si) nanoparticles. Structural morphology, elemental composition, mechanical properties (density, tensile strength, elongation, and hardness), and tribological properties (wear rate and coefficient of friction) of AA 2024 in the presence of CNTs, Si, and its combinations at various proportions were evaluated using a Scanning Electron Microscope (SEM), Energy Dispersive X-Ray Analyzer (EDX), Universal Testing Machine (UTM), Model HMV-2T Vickers hardness test machine, and pin-on-disk friction-and-wear test rig. The Hybrid Metal Matrix Composite (HMMC) material is prepared by a two-stage stir casting method. It was found that the density of the AA 2024 + 4%CNT + 2%Si is 2.22 g/cm3, ultimate tensile strength is 308 N/mm2, elongation is 15.5%, and Vickers hardness is 187.5 Vickers Hardness Number (VHN).