Search Results

Standard

Undervehicle Coupon Corrosion Tests

2016-04-05

CURRENT

J1293_201604

This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.

Standard

UNDERVEHICLE COUPON CORROSION TESTS

1990-01-01

HISTORICAL

J1293_199001

This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.

Standard

Technical Report on Low Cycle Fatigue Properties Ferrous and Non-Ferrous Materials

2002-08-13

HISTORICAL

J1099_200208

Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. Information presented here can be used in preliminary design estimates of fatigue life, the selection of materials and the analysis of service load and/or strain data. The data presented are for the “low cycle” or strain-controlled methods for predicting fatigue behavior. Note that these methods may not be appropriate for materials with internal defects, such as cast irons, which exhibit different tension and compression stress-strain behavior.

Standard

Steering Ball Studs and Socket Assemblies

2012-10-15

CURRENT

J491_201210

This SAE Recommended Practice has been established for the purpose of providing design criteria and suggested dimensional proportions which may be used for ball studs and ball stud socket assemblies as used on steering systems or control mechanisms of passenger vehicles, trucks and off-road equipment. The recommended practice does not cover all applications. It is intended to provide assistance in obtaining functional satisfaction and interchangeability. The inclusion of dimensional data in this report is not intended to imply that all the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning stock production parts.

Standard

Stainless Steel 17-7 PH Spring Wire and Springs

2016-04-05

CURRENT

J217_201604

This SAE Recommended Practice covers a high-quality corrosion-resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document also covers processing requirements of the springs and forms fabricated from this wire.

Standard

Softening Point of Interior Trim Adhesives

2021-01-07

CURRENT

J1700_202101

This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load.

Standard

Shaft Ends

2014-06-05

CURRENT

J501_201406

Standard

STAINLESS STEEL 17-7 PH SPRING WIRE AND SPRINGS

1994-07-01

HISTORICAL

J217_199407

This SAE Recommended Practice covers a high-quality corrosion-resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document also covers processing requirements of the springs and forms fabricated from this wire.

Standard

SOFTENING POINT OF INTERIOR TRIM ADHESIVES

1994-04-21

HISTORICAL

J1700_199404

This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load.

Standard

Proving Ground Vehicle Corrosion Testing

2016-04-05

CURRENT

J1950_201604

The facilities used by domestic automotive manufacturers to provide accelerated corrosion aging of complete vehicles are described in general. The types of vehicles tested, general test methodology, and techniques used to determine test-to-field correlation are discussed. The different procedures used throughout the industry produce different results on various vehicle coatings, components, and systems. The key to successful interpretation of test results is a thorough understanding of the corrosion mechanisms involved and the effects of test limitations on these mechanisms.

Standard

Prevention of Corrosion of Motor Vehicle Body and Chassis Components

2016-04-05

CURRENT

J447_201604

This SAE Information Report provides automotive engineers with the basic principles of corrosion, design guidelines to minimize corrosion, and a review of the various materials, treatments, and processes available to inhibit corrosion of both decorative and functional body and chassis components.

Standard

Peel Adhesion Test for Glass to Elastomeric Material for Automotive Glass Encapsulation

2021-01-07

CURRENT

J1907_202101

This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass. This test method suggests that elastomeric material of less than 172 mpa modulus be used as the encapsulating material. The present practice of encapsulating automotive glass is described as molded-in-place elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with the cured elastomeric material bonded to the perimeter of the glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.

Standard

PROVING GROUND VEHICLE CORROSION TESTING

1989-05-01

HISTORICAL

J1950_198905

The facilities used by domestic automotive manufacturers to provide accelerated corrosion aging of complete vehicles are described in general. The types of vehicles tested, general test methodology, and techniques used to determine test-to-field correlation are discussed. The different procedures used throughout the industry produce different results on various vehicle coatings, components, and systems. The key to successful interpretation of test results is a thorough understanding of the corrosion mechanisms involved and the effects of test limitations on these mechanisms.

Standard

PREVENTION OF CORROSION OF MOTOR VEHICLE BODY AND CHASSIS COMPONENTS

1995-07-01

HISTORICAL

J447_199507

This SAE Information Report provides automotive engineers with the basic principles of corrosion, design guidelines to minimize corrosion, and a review of the various materials, treatments, and processes available to inhibit corrosion of both decorative and functional body and chassis components.

Standard

PEEL ADHESION TEST FOR GLASS TO ELASTOMERIC MATERIAL FOR AUTOMOTIVE GLASS ENCAPSULATION

1988-10-01

HISTORICAL

J1907_198810

This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass. This test method suggests that elastomeric material of less than 172 mpa modulus be used as the encapsulating material. The present practice of encapsulating automotive glass is described as molded-in-place elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with the cured elastomeric material bonded to the perimeter of the glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.

Standard

Overlap Shear Test for Sealant Adhesive Bonding of Automotive Glass Encapsulating Material to Body Opening

2021-01-07

CURRENT

J1836_202101

This recommended practice defines a procedure for the construction of a lap shear specimen for the purpose of testing the bondability of an automotive sealant adhesive to the elastomeric material used in automotive encapsulating. The present practice of encapsulating automotive glass is described as molding elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with cured elastomeric material bonded to the perimeter of thee glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.

Standard

Overlap Shear Test for Automotive Type Sealant for Stationary Glass Bonding

2021-01-07

CURRENT

J1529_202101

This SAE Recommended Practice defines a procedure for the construction and testing of glass to metal lap shears for determining shear strength of sealant adhesives for automotive stationary glass bonding. This procedure can also be used for fiber reinforced plastic (FRP) when used in place of metal.

Standard

OVERLAP SHEAR TEST FOR SEALANT ADHESIVE BONDING OF AUTOMOTIVE GLASS ENCAPSULATING MATERIAL TO BODY OPENING

1988-10-01

HISTORICAL

J1836_198810

This recommended practice defines a procedure for the construction of a lap shear specimen for the purpose of testing the bondability of an automotive sealant adhesive to the elastomeric material used in automotive encapsulating. The present practice of encapsulating automotive glass is described as molding elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with cured elastomeric material bonded to the perimeter of thee glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.

Standard

OVERLAP SHEAR TEST FOR AUTOMOTIVE TYPE SEALANT FOR STATIONARY GLASS BONDING

1986-05-01

HISTORICAL

J1529_198605

This SAE Recommended Practice defines a procedure for the construction and testing of glass to metal lap shears for determining shear strength of sealant adhesives for automotive stationary glass bonding. This procedure can also be used for fiber reinforced plastic (FRP) when used in place of metal.

Standard

Metric Ball Joints

2012-10-15

CURRENT

J2213_201210

This SAE Standard covers the general and dimensional data for industrial quality ball joints commonly used on control linkages in metric automotive, marine, construction, and industrial equipment applications.