Refine Your Search

Date

Date

Topic

Topic

Standard Forming Magnesium alloys Electrical, Electronics, and Avionics Heat resistant materials AMS B Finishes Processes and Fluids Committee Aluminum Powder metallurgy

Search Results

Viewing 1 to 20 of 464
123Next >Last >>
Sort by title
Standard

Welding, Resistance: Spot and Seam
2007-11-21
CURRENT
AMSW6858B
This specification covers requirements for resistance spot and seam welding of the following metals and their alloys. Group 1 - Aluminum and magnesium Group 2 - Iron, nickel, and cobalt Group 3 - Titanium
Standard

Welding, Resistance: Spot and Seam
2005-10-11
HISTORICAL
AMSW6858A
This specification covers requirements for resistance spot and seam welding of the following metals and their alloys. Group 1 - Aluminum and magnesium Group 2 - Iron, nickel, and cobalt Group 3 - Titanium
Standard

Welding, Electron-Beam
2022-01-21
CURRENT
AMS2681B
This specification defines the procedures and requirements for joining metals and alloys using the electron-beam (EB) welding process.
Standard

WELDABILITY TEST FOR WELD FILLER METAL WIRE
1993-04-01
HISTORICAL
ARP1876A
This SAE Aerospace Recommended Practice defines a method for determining the weldability of weld filler metal in continuous coil or cut length form. It is applicable to all solid (non flux-containing) wires. It is intended as a referee method for testing weld filler metals in case of dispute between purchaser and vendor.
Standard

Ultrasonically Activated Needle Peen Forming
2022-10-26
CURRENT
AMS2588
This specification covers the equipment and process requirements for forming or straightening metal parts using Ultrasonically Activated Needle Peening.
Standard

Training and Approval of Heat-Treating Personnel
2019-06-11
CURRENT
ARP1962B
This SAE Aerospace Recommended Practice (ARP) describes training and approval of personnel performing certain heat-treating and associated operations that could have a material impact on the properties of materials being heat treated. It also recommends that only approved personnel perform or monitor the functions listed in Table 1.
Standard

Training and Approval of Heat-Treating Personnel
2007-05-01
HISTORICAL
ARP1962A
This document requires that the company (facility) employing the personnel ensure a verifiable program of on-the-job training, experience, education, classroom instruction, and evaluation of personnel using either company-created programs or programs described herein.
Standard

The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa
2017-03-21
CURRENT
AMS03_4A
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
Standard

The Chemical Milling Process
2021-07-15
CURRENT
ARP1331C
This practice provides recommendations concerning the chemical milling of aluminum, magnesium, high temperature nickel alloys, titanium alloys, copper alloys, and specialty alloys.
Standard

TREATMENT OF SHEET METAL PARTS Steel Corrosion-Resistant
1976-07-01
HISTORICAL
AMS2550C
This specification covers the engineering requirements for a treatment to provide maximum attainable corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
123Next >Last >>
X