Refine Your Search

Date

Date

Topic

Topic

Human Factors and Ergonomics Exhaust systems Truck and Bus Wheel Committee Standard Titanium alloys Parts and Components Commercial Vehicle On-board energy sources Production Assembling

Search Results

Viewing 1 to 20 of 54
123Next >Last >>
Sort by title
Standard

Wide Base Disc Wheels and Demountable Rims - Truck, Bus, and Trailer
2021-08-02
CURRENT
J876_202108
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheel and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard

Wide Base Disc Wheels and Demountable Rims
2007-04-30
HISTORICAL
J876_200704
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus
2005-03-21
HISTORICAL
J2475_200503
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, R, N and P. SAE configurations FC, K, L, U, and W are not included, but may be added in the future.
Standard

WHEELS/RIMS—TRUCKS—TEST PROCEDURES AND PERFORMANCE REQUIREMENTS
1973-09-01
HISTORICAL
J267A_197309
This SAE Recommended. Practice provides uniform laboratory procedures for fatigue testing certain production disc wheels, spoke wheels, and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose passenger vehicles. Standardized fatigue tests are yet to be developed for wheels/rims not covered in this recommended practice.
Standard

WHEELS/RIMS—TRUCKS—TEST PROCEDURES AND PERFORMANCE REQUIREMENTS
1991-01-01
HISTORICAL
J267_199101
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing certain production disc wheels, and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose passenger vehicles. This document does not cover bolt together divided wheels or other special application wheels and rims.
Standard

WHEELS/RIMS - TRUCKS - TEST PROCEDURES AND PERFORMANCE REQUIREMENTS
1983-12-01
HISTORICAL
J267_198312
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing certain production disc wheels, wheels for demountable rims, and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose passenger vehicles. Standardized fatigue tests are yet to be developed for wheels and rims not covered in this recommended practice.
Standard

Spoke Wheels and Hub Fatigue Test Procedures
2003-03-07
HISTORICAL
J1095_200303
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2019-10-07
CURRENT
J2535_201910
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2013-02-11
HISTORICAL
J2535_201302
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2006-12-06
HISTORICAL
J2535_200612
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions—Truck and Bus
2006-05-22
HISTORICAL
J1671_200605
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. The geometric features described in this document are shown at true position. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2023-05-19
CURRENT
J1671_202305
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2019-10-17
HISTORICAL
J1671_201910
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus
2015-02-20
HISTORICAL
J1671_201502
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
123Next >Last >>
X