Refine Your Search

Date

Date

Topic

Topic

Lubricants Standard Circuit Protection and Switch Device Committee Corrosion Human Factors and Ergonomics Jet fuel Parts and Components On-board energy sources Polymers Exhaust systems

Search Results

Viewing 1 to 20 of 30
12Next >Last >>
Sort by title
Standard

TURN SIGNAL FLASHERS
1968-04-01
HISTORICAL
J590C_196804
Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal system as stated by the manufacturer.
Standard

TURN SIGNAL FLASHERS
1977-01-01
HISTORICAL
J590E_197701
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn signal system as stated by the flasher manufacturer. It is an engineering design standard and is supplemented by SAE J1055 covering service performance requirements for turn signal flashers.
Standard

TURN SIGNAL FLASHERS
1975-07-01
HISTORICAL
J590E_197507
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn signal system as stated by the flasher manufacturer. It is an engineering design standard and is supplemented by SAE J1055 covering service performance requirements for turn signal flashers.
Standard

TURN SIGNAL FLASHERS
1973-09-01
HISTORICAL
J590D_197309
Flasher(s) referred to in this SAE Standard are for nominal 12 V or 6 V d-c circuits and are intended to operate at the design load(s) for the turn signal system as stated by the flasher manufacturer. It is an engineering design standard and is supplemented by SAE J1055 covering service performance requirements for turn signal flashers.
Standard

SIX- AND TWELVE-VOLT CIGAR LIGHTER RECEPTACLES
1990-03-16
HISTORICAL
J563_199003
This SAE Standard covers the basic cigar lighter receptacle, which may optionally incorporate overload protective devices. Figure 1 and Table 1 show the cigar lighter receptacle and its pertinent dimensions. Lighter plugs shall be permanently marked either "6 volt" or "12 volt". Manufacturers of accessory plugs to energize devices such as trouble lamps and razors are cautioned to conform to the provisions given in this document. Live contact of any accessory plug shall be made with the center stud; the contacting member must not be less than 3.56 mm in diameter and have a minimum spherical radius of 2.54 mm at the contacting end. To prevent damage, the body of an accessory plug back of the contact end should be large enough to serve as a centering guide when it is inserted into the receptacle. The contact end of any accessory plug should have sufficient taper so as not to interfere with the receptacle bimetal fingers.
Standard

MINIATURE BLADE TYPE ELECTRICAL FUSES
1990-11-01
CURRENT
J2077_199011
The fuses shown in Figure 1 are for use in motor vehicles, boats, and trailers to protect electrical wiring and equipment. This SAE Standard is for the construction shown and is not intended to restrict the design and use of other configurations and materials capable of meeting the vehicle requirements.
Standard

HIGH CURRENT TIME LAG ELECTRIC FUSES
1990-11-01
CURRENT
J1888_199011
The fuses shown in Figure 1 are for use in motor vehicles, boats, and trailers to protect electrical wiring. This SAE Standard is for the construction shown and is not intended to restrict the design and use of other configurations and materials capable of meeting the vehicle requirements.
Standard

HAZARD WARNING SIGNAL SWITCH
1988-10-01
CURRENT
J910_198810
This standard defines the test conditions, procedures and performance specifications for 6, 12 and 24-V manually actuated hazard warning signal switch.
Standard

ELECTRIC WINDSHIELD WIPER SWITCH
1977-10-01
CURRENT
J112_197710
This SAE Recommended Practice covers temperature test, endurance test setup, and endurance requirements for an electric windshield wiper switch. It also covers the combination windshield wiper and washer switch.
12Next >Last >>
X