Search Results

The purpose of this ARP is to provide criteria that will lead to and support existing regulatory standards of systems for UAM/AMM/eVTOL aircraft such that the emergency systems will facilitate egress under emergency conditions. Consideration is given to existing requirements of the FAA and to the recommendations of aircraft operators and those involved in the manufacture or use of the emergency lighting system. Occupant safety is the primary objective, with appropriate provisions for crew (pilot) system control taken into consideration. Consideration is also given to autonomous aircraft in which passengers are required to egress without the aid or direction of crew. The criteria established herein are intended to produce an emergency lighting system that will comply with the Federal and International Regulations. However, these recommendations are but one means of meeting the objective.

The scope is determine if an 'Electronic Authorized Release Certificate' is viable and what is needed to make it viable.

This specification covers a zinc alloy in the form of die castings.

(From Standards Proposal No. 2358, formulated under the cognizance of the EIA Quality and Reliability Engineering (QRE) Committee.)

Conventional attribute sampling plans based upon nonzero acceptance numbers are no longer desirable. In addition, emphasis is now placed on the quality level that is received by the customer. This relates directly to the Lot Tolerance Percent Defective (LTPD) value or the Limiting Quality Protection of MIL-STD-105. Measuring quality levels in percent nonconforming, although not incorrect, has been replaced with quality levels measured in parts per million (PPM). As a result, this standard addresses the need for sampling plans that can augment MIL-STD-105, are based upon a zero acceptance number, and address quality (nonconformance) levels in the parts per million range. This document does not address minor nonconformances, which are defined as nonconformances that are not likely to reduce materially the usability of the unit of product for its intended purpose.

This specification covers the engineering requirements for electrodepositton of zinc and the properties of the deposit.

This specification covers a zinc alloy in the form of die castings.

This SAE Aerospace Standard (AS) covers 6-point and 12-point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box end and flare nut wrenches, combination open end and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) non-distorting usage; (b) possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 and ISO 8434-2; and (c) transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers 12-point open box end crowfoot, flare nut, double open box end, combination box and open box end, and ratcheting open box end wrenches that are designed with the following requirements: a Nondistorting usage b Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514. c Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers 12 point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: a. Non-distorting usage b. Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514. c. Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers 12 point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) Non-distorting usage; (b) Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514; (c) Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.