Search Results

This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.

The purpose of this ARP is to provide criteria that will lead to and support existing regulatory standards of systems for UAM/AMM/eVTOL aircraft such that the emergency systems will facilitate egress under emergency conditions. Consideration is given to existing requirements of the FAA and to the recommendations of aircraft operators and those involved in the manufacture or use of the emergency lighting system. Occupant safety is the primary objective, with appropriate provisions for crew (pilot) system control taken into consideration. Consideration is also given to autonomous aircraft in which passengers are required to egress without the aid or direction of crew. The criteria established herein are intended to produce an emergency lighting system that will comply with the Federal and International Regulations. However, these recommendations are but one means of meeting the objective.

This specification covers the requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating.

This specification covers a zinc alloy in the form of die castings.

This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.

This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.

This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.

This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.

This standard1 describes the chemical, mechanical, and dimensional requirements for a wide range of wrought copper and copper alloys used in the automotive and related industries.

For convenience, this SAE Information Report is presented in two parts as shown below. To avoid repetition, however, data applicable to both wrought and cast alloys is included only in Part 1. Part I—Wrought Copper and Copper Alloys Types of Copper (Table 1) General Characteristics (Table 3) Electrical Conductivity Thermal Conductivity General Mechanical Properties (Table 10) Yield Strength Fatigue Strength Physical Properties (Table 2) General Fabricating Properties (Table 3) Formability Bending Hot Forming Machinability Joining Surface Finishing Color Corrosion Resistance Effect of Temperature Typical Uses (Table 3) Part II—Cast Copper Alloys Types of Casting Alloys Effects of Alloy Elements and Impurities General Characteristics (Table 11) Physical Properties (Table 12) Typical Uses (Table 11)

For convenience, this SAE Information Report is presented in two parts as shown below. To avoid repetition, however, data applicable to both wrought and cast alloys is included only in Part 1. Part I—Wrought Copper and Copper Alloys Types of Copper (Table 1) General Characteristics (Table 3) Electrical Conductivity Thermal Conductivity General Mechanical Properties (Table 10) Yield Strength Fatigue Strength Physical Properties (Table 2) General Fabricating Properties (Table 3) Formability Bending Hot Forming Machinability Joining Surface Finishing Color Corrosion Resistance Effect of Temperature Typical Uses (Table 3) Part II—Cast Copper Alloys Types of Casting Alloys Effects of Alloy Elements and Impurities General Characteristics (Table 11) Physical Properties (Table 12) Typical Uses (Table 11)

This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.

This standard describes the chemical, mechanical, and dimensional requirements for a wide range of wrought copper and copper alloys used in the automotive and related industries. Wrought forms covered by this standard include sheet, strip, bar, plate, rod, wire, tube, and shapes; however, form required must be specified by purchaser.

This standard1 describes the chemical, mechanical, and dimensional requirements for a wide range of wrought copper and copper alloys used in the automotive and related industries.

This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter.

This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter (see 8.5).

This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter (see 8.4).

This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter (See 8.4).

This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter.

This specification covers concentric lay stranded and rope-lay stranded round electrical conductor fabricated from copper, copper alloy or aluminum. This specification also covers thermocouple extension conductor fabricated from nickel/chromium or nickel/aluminum/manganese. The conductors in this specification are suitable for use in insulated wires used in aerospace and other applications.