Search Results

OBD system requirements were first developed by the California Air Resources Board, the U.S. Environmental Protection Agency, and the European Commission. New OBD requirements should be as consistent as possible with existing requirements to maximize reliability and to minimize system complexity, proliferation of configurations, and consumer cost. New OBD requirements from around the world are briefly reviewed and most are consistent with the original U.S. and European requirements. Worldwide OBD requirements are being further harmonized under the United Nations, Economic Commission for Europe, World Forum for Harmonization of Vehicle Regulations (WP29). Presenter David H. Ferris, General Motors Company

Wireless power transfer (WPT) of plug-in and battery electric vehicles (PEV�s) rely on loosely coupled transformer operating in magnetic resonance to tune out reactive effects. Depending on the degree of coupling, such systems experience a single peak response that trends to bifurcate as the coefficient of coupling increases. This places additional burden on the WPT grid side power controller to not only manage the power transfer process but to manage the transmit coil to receiver coil reactive power in response to vehicle ground clearance and misalignment tolerance. In addition, the WPT rectified output voltage must dynamically match the vehicle on-board regenerative energy storage system (RESS). This paper examines the essentials of WPT operation and challenges facing the commercialization of wireless charging. Experimental results obtained from the Oak Ridge National Laboratory WPT apparatus are presented as validation of the theory. Presenter John Miller, ORNL

Auto manufacturers have known and surveys confirm that consumers require short payback periods (2-4 years) for investments in fuel economy. Using societal discount rates, engineering-economic generally find substantial potential to increase fuel economy, cost-effectively. This phenomenon, often referred to as the ?energy paradox?, has been observed in nearly all consumers? choices of energy-using durable goods. Loss aversion, perhaps the most well established theory of behavioral economics, provides a compelling explanation. Engineering economic analyses generally overlook the fact that consumers? investments in fuel economy are not sure things but rather risky bets. Future energy prices, real world on-road fuel economy, and many other factors are uncertain. Loss aversion describes a fundamental human tendency to exaggerate the potential for loss relative to gain when faced with a risky bet. It provides a sufficient explanation for consumers?

This presentation provides a overview of validating Time Triggered Ethernet (TTE) for use as the network to interconnect the avionics for manned Space Vehicle. The next manned Space Vehicle will use Time Triggered-Gigabit Ethernet (TT-GbE) leveraged from commercial development of TTE critical Intellectual Property. There are several validation considerations of either separating TTE segments or adding new TTE segments onto the network caused by the different phases of a manned space vehicle from pre-launch to re-entry. Considerable amount of validation testing has been successfully performed on TT-GbE/TTE. Presenter Victor Revelle, Honeywell International Inc.

This presentation shows the SCADE System product line for systems modeling and generation based on the SysML standard and the Eclipse Papyrus open source technology. SCADE System has been developed in the framework of Listerel, a joint laboratory of Esterel Technologies, provider of the SCADE�, and CEA LIST, project leader of the Eclipse component, Papyrus. From an architecture point of view, the Esterel SCADE tools are built on top of the SCADE platform which includes both SCADE Suite�, a model-based development environment dedicated to critical software, and SCADE System enabling model-based system engineering. SCADE System includes Papyrus, an open source component (under EPL license), integrated in the modeling platform of Eclipse. Using this integrated modeling platform, both system and software teams share the same environment for system development. Furthermore, other model-based tools can be added to the environment, due to the use of Eclipse.

Many manufacturing companies want to apply AFP technology to complex high-curvature part shapes. As new AFP machine technologies are developed to specifically apply material over complex shapes, new and innovative NC programming approaches are needed to successfully, reliably, and accurately apply material with good consolidation, while meeting the fiber direction and coverage requirements. A big issue with AFP is the production rate vs. part complexity. Most complex shapes can be created with a single .125? wide strip (tow) of material. But the production time would be impractically long. So machine builders create 6, 8, 16, even 32 tow AFP heads, and use the widest tow possible for the highest laydown rates. But then wide compaction rollers on these systems have difficulty consolidating material over curved surfaces, and the minimum steering radius of wider tows challenge the software?s ability to meet the layup requirements.

Revisions to the California OBD-II diesel regulations required many updates to various SAE and ISO on-board diagnostic standards; these include major revisions to SAE J1979, J1699-3, J2012 and J1930. This presentation is intended to review the background for these changes as well as the revisions made in these documents. Presenter Robert Gruszczynski, Volkswagen of America

Update on light-duty regulations. Presenter Michael J. McCarthy, California Air Resources Board

Automakers, suppliers, public agencies, interest groups and others are increasingly embracing the environment as one of the dominant forces in the US automotive market. All parties have a strong vested interest in understanding how environmental concerns will influence design, production, marketing and usage of tomorrow�s vehicles. A common need of all parties is independent and actionable information to enable them to make better decisions and have the greatest chance of being successful in this uncertain future. Four factors - an uncertain economic climate; a constantly changing governmental regulatory system; advancements in powertrain technology; and ever-present environmental concerns - continue to shape the automotive landscape. While automakers are focused on developing alternative powertrains and alternative fuel options for an increasingly �green� vehicle market, J.D.

The automotive industry is in a time of great innovation. As a result of policy initiatives, car companies must build and market low or zero emission vehicles (ZEVs) such as plug-in hybrids (the Volt) and battery electric vehicles (the Leaf). Consumer interest in these types of vehicles does not, however, match the necessary sales that automotive OEMs are being held to. I will present consumer data that informs both the OEMs and public policy and demonstrate how the electrification of the fleet is the greatest marketing challenge the world has seen. Presenter Stephen Popiel, Synovate Motoresearch

Engine Boosting Systems. Presenter Andrew Williams, Loughborough Univ.

TAUPE is a collaborative research project co-funded by the European Commission in the framework of the Seventh Framework Programme (FP7). It addresses the aeronautic sector and is composed of 17 partners from 6 European countries. The project lasts 3,5 years (September 2008 ? February 2012), is led by Safran Engineering Services (Labinal, SAFRAN Group) and has a budget of 5.5M?. The project aims to simplify the electrical architecture of aircraft and to reduce the length and mass of cabling by introducing PLC (PowerLine Communication) or PoD (Power over Data) technologies inside the aircraft. Both technologies essentially aim to supply power and data over the same cable.

Developing relatively cheap and widely available resources for heterogeneous solid catalyst synthesis is a promising approach for biodiesel fuel industry. Seashell which is essentially calcium carbonate can be used as a basic support for transesterification heterogeneous catalysts. In the present investigation, the alcoholysis of waste frying oil has been carried out using seashell-supported K3 PO4 as solid catalyst. Presenter Essam Oun Al-Zaini, PhD student, UNSW

Toyota is committed to the development of advanced powertrains to help address concerns with future oil supplies, the impacts of increased carbon dioxide emissions, and air pollution. Towards that end Toyota is planning to bring to market in 2012 a plug-in hybrid vehicle, a short range electric vehicle, a long range electric vehicle and in the 2015 timeframe hydrogen powered fuel cell vehicle. This presentation will focus on our electric vehicle plans and the challenges with bringing electric vehicle to the market. From the 2010 Alt Fuels Study, Toyota has identified that two key barriers for EV adoption are the times to charge the vehicle, and electricity cost. The study finds that the current infrastructure could be sufficient for most driving needs but EV drivers will still need to alter their driving habits slightly.

From 2009 until present Toyota has had a demonstration program of Prius PHV which is comprised of 600 vehicles throughout Japan, Europe and in the US. The vehicles were given to government agencies, corporations, utility companies and private individuals to use. With these demo units Toyota wanted to understand the market reaction and real world impact of plug-in technology on gasoline displacement with increased use of electricity as a fuel. This presentation shows that approximately 50% of fuel was saved using the PHVs in the US. An experiment in Toyota City shows that if public infrastructure is optimized to be convenient and located where people normally park, there is a potential to achieve an ideal fuel savings of 61%. The demonstration program shows that plug-in technology in fact saves fuel and that the proper infrastructure can optimize the fuel savings of plug-in hybrids. Presenter Avernethy Francisco, Toyota

Ford's EcoBoost GTDI engine technology (Gasoline Direct Injection, Turbo-charging and Downsizing) is being successfully implemented in the market place with the EcoBoost option accounting for significant volumes in vehicle lines as diverse as the F150 pickup truck, Edge CUV and the Lincoln MKS luxury sedan. A logical question would be what comes after GTDI? This presentation will review some of the technologies that will be required for further improvements in CO2, efficiency and performance building on the EcoBoost foundation as well as some of the challenges inherent in the new technologies and approaches. Presenter Eric W. Curtis, Ford Motor Co.

Polypropylene is typically reinforced with commodities that are non renewable and require a great deal of energy to produce. The marketplace needs a reinforcement that can offer beneficial physical properties, such as impact, while being attained from a renewable green source. Compounding flax fiber, which is traditionally an agricultural waste product burned by farmers, with polypropylene yields physical properties similar to traditional glass filled polypropylene. This combination should lead to cost saving opportunities while not sacrificing part performance. Presenter James Preston, Rhetech Inc.

There are now a wide variety of Hybrid and Electric Vehicles in or near production. They reduce or displace petroleum consumption with of various combinations of conventional IC engine, mechanical transmission, liquid fuel storage, electrical energy storage, electrical and electro-mechanical energy conversion, and vehicle-to-grid energy interface. These Electrified types of vehicles include Mild Hybrid, Full Hybrid, Plug-In Hybrid, Extended Range Electric, and Battery Electric. Some types differ in their actual usability for the real mixes of driving trips, and further that differ in their effectiveness to reduce or displace fuel in actual real world driving use. Vehicle size is also a factor in total vehicle utility in transporting people. If we may segment drivers by their driving needs, in each segment, we see a particular type of electrified vehicle that is better suited than others at minimizing fuel cost and petroleum consumption for the purposes of transporting people.

There has recently been a great deal of hypothesizing and prognosticating about the security of supply of the rare earths for the non-Chinese OEM automotive industry. The pundits and industry analysts have warned of demand destruction by substitution driven by sustained high prices as well as due to supply interruptions. What has been overlooked for the most part is that the issue is not about all of the rare earths; it is just about some of them, the critical rare earths. And even in that category there are two separate issues: 1) Is there enough production of the light rare earth, neodymium, to sustain current demand and can its non-Chinese production grow to meet expected non-Chinese demand? and 2.) Is there even enough production of the heavy rare earths, dysprosium and terbium, to meet current Chinese demand and is it possible to produce dysprosium a.) Outside of China, and b.)

Gasoline engines continue to suffer from significant pumping losses despite decades of effort focused on reducing throttling. Honeywell Turbo has developed a throttle with an integrated turbine/generator that generates electricity by recovering pumping work. This energy offsets power normally provided by the crank driven alternator, thereby saving fuel. It integrates well with modern electrical systems which employ smart charging and idle stop strategies. The ThrottleCharger provides fuel economy benefits up to 5% over federal test cycles and in real world conditions. Presenter Mike Guidry, Honeywell Int'l (Turbo Technologies)