Search Results

The fatigue behavior of Hilok fastener joints under constant amplitude loading has been investigated experimentally. The effects of load transfer in an unbalanced joint configuration was characterized in terms of a stress severity factor relative to the open-hole configuration. The experimental data indicates that the clamp-up forces dominate the performance of fastener joints with the open-hole fatigue life being the lower bound at the stress levels investigated. The failure modes were observed to transition from a net-section type failure across the minimum section to a fretting induced failure at some distance from the hole. The experimental data has been used to develop stress severity factors to be used as a measure of the fatigue quality of the fastener joints.

This paper presents a method by which artificial neural networks can be trained and used to identify a possible spin entry, differentiate between an incipient spin and a stabilized spin, and predict required recovery controls. These were then implemented into a simulation and tested using data from actual flight tests conducted by NASA Langley Research Center, to verify that artificial neural networks can successfully be used for this application. The spin avoidance and recovery system functioned properly. In addition, a weighting system was developed to predict possible spin characteristics of aircraft, depending on the relative magnitude of the three principal moments of inertia.

While operational airships globally number in the low dozens, interest in buoyant or semi-buoyant platforms continues to arouse imaginations of commercial and military planners and developers alike. The airship-as-advertisement business model is the only model that has proven sustainable on any scale since the crash of the initially successful LZ-128 Hindenburg effectively ended regular passenger and cargo transport by airship, and the 1962 termination of the US Naval airship program terminated regular large-scale surveillance from airships. Efforts in the US and Japan during the 2000's to have a self-sustaining sight-seeing business model using the modern semi-rigid Zeppelin NT both failed. In theory, the buoyant nature of airships provides compelling endurance and cost-per-ton-mile capability which fills a niche arguably not currently occupied by other modes of transportation.

A generalized upper bound model for calculating the chip flow angle in oblique cutting using flat faced tools with single cutting edge and multiple or curved cutting edges has been developed. The chip flow angle and chip velocity are obtained by minimizing the cutting power with respect to both these variables. The chip flow angles predicted by this model show good agreement with experimental values of chip flow angles for various tool geometries and cutting conditions. The model has the potential to be extended to the more complex machining processes such as drilling and milling.

The Refill Friction Spot Joining (RFSJ) is an emerging solid-state spot welding technology that thermo-mechanically creates a molecular-level bond between the work-pieces. RFSJ does not consume any filler or foreign materials so that no additional weight is introduced to the assembly. As the solid-to-liquid phase transition is not involved in RFSJ in general, there is no lack of fusion or material deterioration caused by liquefaction and solidification. Unlike the conventional friction stir spot welding, RFSJ produces a spot joint with a perfectly flush surface finish without a key or exit hole. Currently, the aerospace industry employs solid rivets for fastening the primary structures as they meet the baseline requirements and have well-established standards and specifications.

The necessity of avoiding the destructive and non-repeatable FSST (Full Scale Sled Test) makes it desirable to devise a cheaper and more repeatable method which can supplant this test procedure. This need developed the HCTD (HIC Component Testing Device) which is capable of providing conservative HIC results with higher repeatability. The computational model of the HCTD is validated against one of the tests conducted at CAMI with polyethylene foam. This validated model is used to conduct a series of tests with input parameters similar to the sled test to develop the correlation between the sled test and HCTD. This study hence concludes that a validated computational model of HCTD can be successfully utilized to address the HIC compliance issues for a foam padded surface.

Ice particles shed from aircraft surfaces are a safety concern because they can damage aft-mounted engines and other aircraft components. Ice shedding is a random and complex phenomenon. The randomness of the ice fragment geometry, size, orientation and shed location in addition to potential particle breakup during flight poses considerable simulation challenges. Current ice shedding analysis tools have limited capabilities due to the lack of experimental aerodynamic coefficients for the forces and moments acting on the ice fragment. A methodology for simulating the shedding of large ice particles from aircraft surfaces was developed at Wichita State University. This methodology combines experimental aerodynamic characteristics of ice fragments, computational fluid dynamics, trajectory analysis and the Monte Carlo method to provide probability maps of shed particle footprints at desired locations.

Presented here are analyses and statistical summaries of data collected from 11,299 flight operations recorded on 6 BE-1900D aircraft during routine commuter service over a period of three years. Basic flight parameters such as airspeed, altitude, flight duration, etc. are shown in a form that allows easy comparison with the manufacturer's design criteria. Lateral ground loads are presented for ground operations. Primary emphasis is placed on aircraft usage and flight loads. Maneuver and gust loads are presented for different flight phases and for different altitude bands. In addition, derived gust velocities and various coincident flight events are shown and compared with published operational limits.

A methodology for developing spray rigs for icing cloud simulation is presented. This methodology includes Computational Fluid Dynamics (CFD) analysis and icing tunnel experiments and was applied to design a spray rig system for a small airborne icing tanker. An in-house spray system was developed and tested in a laboratory to assess two commercially available nozzles - a single-jet type and a multi-jet type - which were capable of producing both FAR Part 25 Appendix C and SLD icing clouds. Spray rig characteristics evaluated during the laboratory tests included air and water flow rates as well as droplet size and distributions. The effects of airspeed and nozzle spacing on spray plume size and uniformity were investigated in a small icing tunnel facility with a two-nozzle spray rig. The experimental data were compared with three-dimensional numerical simulation results obtained with the FLUENT software.

Dynamic aircraft seat regulations are identified in the Code of Federal Regulations (CFR), 14 CFR Parts § 23.562 [1] and § 25.562 [2] for crashworthy evaluation of a seat in dynamic environment. The regulations specify full-scale dynamic testing on production seats. The dynamic tests are designed to demonstrate the structural integrity of the seat to withstand an emergency landing event and occupant safety. SAE standard AS 8049 [3] supports detailed information on dynamic seat testing procedure and acceptance criteria. Full-scale dynamic testing in support of certification is expensive and repeated testing due to failure drastically increases the expense. Involvement of impact environment, flexibility in interior configuration and complicated nature of seat engineering design makes this problem quite complex, so that classical hand calculations are practically impossible.

A supplier satisfaction survey was developed and administered to 129 Aircraft suppliers who are AS9100 registered. The primary objective of the survey was to assess organizational benefits, attributed to the AS9100 standard, and registration process difficulties. Survey results from 49 responses indicated that the primary reason for seeking AS9100 registration was customer requirement, followed by improving production and service. Further analysis indicated that the top three difficulties were evaluating effectiveness of employee training, obtaining and analyzing data on customer feedback and satisfaction, and monitoring and measuring processes. The top three reported benefits, improved quality awareness among employees, an increase in employee training, and improved internal communication, respectively, were all non-financial in nature.

An experimental investigation was conducted to identify the aerodynamic effects of oversized low-pressure (Tundra) tires and tall landing gear on a Piper Super Cub airplane. Water tunnel and wind tunnel tests were performed using, respectively, a 1/20 scale model and full-scale landing gear and tire components. Force and moment data suggest that larger tires and taller gear most affect the drag and side force. Small trim changes are apparent, but the basic static stability behavior appears unchanged.