Search Results

Abstract The increase in worldwide awareness of environmental issues has necessitated the air transport industry to drastically reduce carbon dioxide emissions. To meet this goal, one solution is the electrification of aircraft propulsion systems. In particular, single-aisle aircraft with partial turboelectric propulsion with approximately 150 passenger seats in the 2030s are the focus. To develop a single-aisle aircraft with partial turboelectric propulsion, an air-cooled interior permanent magnet (IPM) motor with an output of 2 MW is desired. In this article, mathematical system equations that describe heat transfer inside the target air-cooled IPM motor are formulated, and their mathematical analytical solutions are obtained.

Abstract The civil aircraft nosewheel is clamped, lifted, and retained through the pick-up and holding system of the towbarless towing vehicle (TLTV), and the aircraft may be moved from the parking position to an adjacent one, the taxiway, a maintenance hangar, a location near the active runway, or conversely only with the power of the TLTV. The TLTV interfacing with the nose-landing gear of civil transport aircraft for the long-distance towing operations at a high speed could be defined as a towbarless aircraft taxiing system (TLATS). The dynamic loads induced by the system vibration may cause damage or reduce the certified safe-life limit of the nose-landing gear or the TLTV when the towing speed increases up to 40 km/h during the towing operations due to the maximum ramp weight of a heavy aircraft.

Abstract In this article, Al-Mg-Si-Mn alloy (AA6082) is butt joined by employing friction stir welding (FSW). The mechanical and metallurgical properties of joints are analyzed by conducting tensile and microhardness testing, respectively. To measure the temperature at different locations, eight thermocouples (L-shaped k-type) are placed at equal distance from the centerline. Least square method attempts to calculate the temperature at the centerline of joints. The process parameters are also optimized using Taguchi’s five-level experimental design. The optimum process parameters are determined, employing ultimate tensile strength (UTS) as a response parameter. A statistical test “analysis of variance” is used to check the adequacy of the model. It has been observed that rotational speed and feed rate are the predominant factors for UTS and microhardness.

Abstract At hypersonic speed, severe aerodynamic heating is observed, and temperatures are too high to cool by radiation cooling; active cooling such as ablative cooling is helpful in this situation. The Thermal Protection System (TPS) consists of a layer of an ablative material, followed by an insulating material to lower the temperature at the inside wall of the lifting body. The surface area (considering the inside volume of the vehicle constant) of the TPS plays a vital role in heat transfer to the vehicle and heat transferred through the vehicle body. The minimum area sweepback angle (ΛArea-min) is the function of the principal radius (R) and the ratio of the principal radii of the forward bi-curvature stagnation surface (R/r). The ΛArea-min = 80° is obtained for R = 2 m and R/r = 2. The aerothermal analysis of the lifting body is of fundamental interest while designing the TPS.

Abstract An aeroengine exhaust plume is one of the important sources of infrared (IR) signature in the 3-5 μm and the 2-3 μm bands. Analysis, characterization, and modeling of the exhaust plume IR emission are needed for insight into its role in aircraft survivability against IR-guided missiles. The IR signature estimation of aeroengine exhaust needs estimation of radiative properties of absorbing-emitting exhaust gases, e.g., carbon dioxide (CO2) and water vapor (H2O). The radiative properties of the gases can be estimated by a mathematical model with a spectroscopic database of these gases. Low-Resolution Transmission (LOWTRAN), Moderate-Resolution Transmission (MODTRAN), High-Resolution Transmission (HITRAN), and High-Temperature Transmission (HITEMP) are some commonly used spectroscopic databases. This study compares Statistical Narrowband (SNB) models with the various other mathematical models used for the estimation of radiative properties of exhaust gases.

Abstract Electric ducted-fans with high power density are widely used in hybrid aircraft, electric aircraft, and VTOL vehicles. For the state-of-the-art electric ducted-fan, motor cooling restricts the power density increase. A motor design model based on the fan hub-to-tip ratio proposed in this article reveals that the thermal coupling effect between fan aerodynamic design and motor cooling design has great potential to increase the power density of the motor in an electric propulsion system. A smaller hub-to-tip ratio is preferred as long as the power balance and cooling balance are satisfied. Parametric study on a current 6 kW electric ducted-fan system shows that the highest motor power density could be increased by 246% based on the current technology. Finally, a preliminary design was obtained and experiments were conducted to prove the feasibility of the model.

Abstract The main technical barrier to commercial use of microturbines is its low efficiency, not exceeding 15%. Efficiency and specific power are as high as the Turbine Inlet Temperature (TIT), generally limited to 950°C in microturbines, as its tiny rotors make internal blade cooling impossible. This work uses Computational Fluid Dynamics (CFD) to develop an external cooling system of the blades of a microturbine by incorporating a compressor into the disk to blow air over the blades’ walls. The engine used as the basis of the work is the FD-3/64. The work was divided into two steps. In the first, Step 1, the reactive flow in the combustor was simulated to obtain the boundary conditions for Step 2. In Step 2, the flow through the turbine wheel during rotation is simulated. Four rotor models were simulated.

Abstract It is reasonable to use a two-phase heat transfer loop (TPL) in a thermal control system (TCS) of spacecraft with large heat dissipation. One of the key elements of TPL is a heat-controlled accumulator (HCA). The HCA represents a volume which is filled with vapor and liquid of a single working fluid without bellows. The pressure in a HCA is controlled by the heater. The heat and mass transfer processes in the HCA can proceed with a significant nonequilibrium. This has implications on the regulation of TPL. This article presents a mathematical model of nonequilibrium heat and mass transfer processes in an HCA for microgravity conditions. The model uses the equations of mass and energy conservation separately for the vapor and liquid phases. Interfacial heat and mass transfer is also taken into account. It proposes to use the convective component k for the level of nonequilibrium evaluation.

Abstract A key problem of the construction of fully electric aircraft is the limited energy density of battery packs. It is generally accepted that this can only be overcome via new, denser battery chemistry together with a further increase in the efficiency of power utilization. One appealing approach for achieving the latter is using laser-assisted filler-based joining technologies, which offers unprecedented flexibility for achieving battery cell connections with the least possible electrical loss. This contribution presents our results on the effect of various experimental and process parameters on the electrical and mechanical properties of the laser-formed bond.

Abstract The hot corrosion studies for the die-casted magnesium (Mg) silver (Ag) alloys are carried out through the steam heating route. The Magnesium Silver (QE22A) alloy is fixed under the top lid of the pressure cooker (2 liters) and filled with water and 5% salt (NaCl) solution. The specimens are treated with different time intervals (10, 20, and 30 minutes), with the steam temperature maintained at 100°C around the specimen. The results showed an increase in the corrosion rate with the increase in the steaming time. Further, after the specimens have cooled down to room temperature, similar experiments are repeated for the second and third cycles. Here the formation of the oxide layers over the specimen has reduced the corrosion rate. The structural, surface study was carried out through scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy-dispersive spectroscopy (EDS) to know the corrosion behavior on the specimen.

Abstract Turboshaft engines, one of the classifications of the helicopters, combine the core engine and fan and consume fossil fuels. Using of fossil fuel causes global warming and environmental pollution, such as ecological, human health. To improve helicopter capability, energy is the first point of improvement. High-energy efficient helicopter engines help decrease the environmental damage. Exergy should be applied to the system to determine the maximum available energy. In this study, energy analysis and exergy analysis have been applied to a turboshaft helicopter engine. According to the result of this study, the maximum energy and exergy efficiencies are found to be 21.99% and 15.87%, respectively, at 1500 Shaft Horsepower (SHP). It is seen that the efficiencies increase with the increase of the engine power. Besides, exergy destructions and exergy loss values are presented by calculating different powers.

Abstract In the autumn of 2018, a pilot study using a prototype (PAR46 size) landing light that incorporated ultraviolet light emitting diodes (UVLEDs) was attached on a one-quarter scale remote controlled (RC) plane. The plane was flown in the direction of birds to measure their behavioral response to the approaching plane with landing lights either turned ON or OFF. Data were collected from multiple sources including cameras on the plane and the ground and a bird radar unit to measure the flight path separation between the plane and the birds. The purpose of this study was to determine the effectiveness of using UVLEDs integrated into a PAR46 landing light to trigger bird avoidance behavioral responses that would increase flight path separation to reduce the incidence of bird strikes. The findings showed the mean distance of the avoidance response was statistically significantly greater when the PAR46 landing light with UVLEDs was turned ON versus OFF.

Abstract Analysis and design of total temperature probes for accurate measurements in hot, high-speed flows remains a topic of great interest in aerospace propulsion and a number of other engineering areas. One can apply detailed computational methods for simultaneous convection, conduction and radiation heat transfer, but such approaches are not suitable for rapid, routine analysis and design studies. For these studies, there is still a place for low-order approximate methods, and that is the subject of this paper. Here, an enhanced, low-order model is presented that includes conduction with variable thermal conductivity, convection with varying convection coefficient, varying diameter (and thus area) along the length of the sensor and radiation, all implemented in a convenient MATLAB code.

Abstract The use of nanomaterials and nanostructures have been revolutionizing the advancements of science and technology in various engineering and medical fields. As an example, Carbon Nanotubes (CNTs) have been extensively used for the improvement of mechanical, thermal, electrical, magnetic, and deteriorative properties of traditional composite materials for applications in high-performance structures. The exceptional materials properties of CNTs (i.e., mechanical, magnetic, thermal, and electrical) have introduced them as promising candidates for reinforcement of traditional composites. Most structural configurations of CNTs provide superior material properties; however, their geometrical shapes can deliver different features and characteristics. As one of the unique geometrical configurations, helical CNTs have a great potential for improvement of mechanical, thermal, and electrical properties of polymeric resin composites.

Abstract For spacecraft with high power consumption, it is reasonable to build the thermal control system based on a two-phase mechanically pumped loop. The heat-controlled accumulator is a key element of the two-phase mechanically pumped loop, which allows for the control of pressure in the loop and maintains the required level of coolant boiling temperature or cavitation margin at the pump inlet. There can be two critical modes of loop operation where the ability to control pressure will be lost. The first critical mode occurs when the accumulator fills with liquid at high heat loads. The second critical mode occurs when the accumulator is at low heat loads and partial loss of coolant, for example, due to the leak caused by micrometeorite breakdown. Both modes are caused by insufficient accumulator volume or working fluid charge.

Abstract For electromechanical actuators (EMAs) and electronic devices cooling on aircraft, there is a need to study cooling fan performance at various altitudes from sea level to 12,000 m where the ambient pressure varies from 1 to 0.2 atm. As fan static pressure head is proportional to air density, the fan’s rotational speed has to be increased significantly to compensate for the low ambient pressure of 0.2 atm at the altitude of 12,000 m. To evaluate fan performance for EMA cooling, a high-rotational-speed, commercially available fan made by Ametek with a diameter of ~82 mm and ~3 m3/min zero-load open cooling flow rate when operating at 20,000 rpm was chosen as the baseline. According to fan scaling laws, this fan was expected to meet the cooling needs for an EMA when operating at 0.2 atm. Using a closed flow loop, the performance of the fan operating in the above ambient pressure range and at a rotational speed between 15,000 and 30,000 rpm was evaluated.

Abstract Speckle noise degrades the visual appearance and the quality of a synthetic aperture radar (SAR) image. The reduction of speckle noise is the first step in any remote-sensing device. To improve the noisy SAR images, a variety of adaptive and nonadaptive noise reduction filters were used. In order to eliminate speckle noise present in SAR images, an adaptive cuckoo search optimization-based speckle reduction bilateral filter has been designed in this article. To test the ability to eliminate multiplicative noise, the suggested filter’s effectiveness was compared to that of several de-speckling approaches. It has been measured with different assessment metrics such as PSNR, EPI, SSIM, and ENL. When compared to conventional de-noising filters, the proposed filter shows promising results for lowering speckle noise and retaining edge properties.

Abstract At supersonic aircraft speeds, aerodynamically heated surfaces, e.g., nose, wing leading edges, are infrared (IR) signature sources from the tactically crucial frontal aspect. This study numerically predicts and then illustrates the minimization of IR contrast between the nose and background sky radiance by the emissivity optimization (εw,opt) technique, which has the least performance penalties. The IR contrast between the aircraft nose and its replaced background in 1.9-2.9 μm short-wave IR (SW-IR), 3-5 μm medium-wave IR (MW-IR), and 8-12 μm long-wave IR (LW-IR) bands are obtained. The IR contrast especially in LW-IR (i) increases with flight Mach number (M ∞) for a given flight altitude (H) and εw (ii) decreases with increasing H for a given M ∞ and εw. The εw,opt for a flight altitude of 5 km is found to decrease from 0.99 at M ∞ = 0.001 (low subsonic) in all three bands to 2 × 10−4 in MW-IR and 0.0213 in LW-IR bands at M ∞ = 3 (high supersonic).

Abstract Improving the energy performance of batteries can increase the reliability of electric aircraft. To achieve this goal, battery management systems (BMS) are required to keep the temperature within the battery pack and cells below the safety limits and make the temperature distribution as even as possible. Batteries have a limited service life as a result of unwanted chemical reactions, physical changes that cause the loss of active materials in the structure, and internal resistance increase during the charging and discharging cycle of the battery. These changes usually affect the electrical performance of batteries. Battery life can be increased only by reducing or preventing unwanted chemical reactions. Lithium-ion (Li-ion) batteries are a suitable option due to their high specific energy and energy density advantages. In this study, the necessity of heat management is emphasized. The discharge tests of the Li-ion battery provided 94.6 Wh under 10C and 90.9 Wh under 1C.

Abstract The demand for contactless, rapid manufacturing has increased over the years, especially during the COVID-19 pandemic. Additive manufacturing (AM), a type of rapid manufacturing, is a computer-based system that precisely manufactures products. It proves to be a faster, cheaper, and more efficient production system when integrated with cloud-based manufacturing (CBM). Similarly, the need for semiconductors has grown exponentially over the last five years. Several companies could not keep up with the increasing demand for many reasons. One of the main reasons is the lack of a workforce due to the COVID-19 protocols. This article proposes a novel technique to manufacture semiconductor chips in a fast-paced manner. An algorithm is integrated with cloud, machine vision, sensors, and email access to monitor with live feedback and correct the manufacturing in case of an anomaly.