Search Results

THIS STANDARD ESTABLISHES THE DIMENSIONAL AND VISUAL QUALITY REQUIREMENTS, LOT REQUIREMENTS, AND PACKAGING AND LABELING REQUIREMENTS FOR D-RINGS MOLDED FROM MIL-P-25732 ACRYLONITRILE BUTADIENE (NBR) RUBBER. IT SHALL BE USED FOR PROCUREMENT PURPOSES.

RADIATION can produce almost instantaneous failure of modern aircraft lubricants, tests at Southwest Research Institute show. Two types of failures demonstrated are rapid viscosity rise and loss of heat conductivity. Furthermore, it was found that lubricants can become excessively corrosive under high-level radiation. Generally speaking, the better lubricants appeared to improve in performance while marginal ones deteriorated to a greater extent under radiation. When the better lubricants were subjected to static irradiation prior to the deposition test, there was a minor increase in deposition number as the total dose was increased.

The YF-23A Advanced Tactical prototype Fighter was a revolutionary statically unstable, twin engine aircraft that cruised at supersonic speeds without afterburner and was designed to out maneuver opponents at subsonic and supersonic speeds. Combining these capabilities into a chosen aircraft configuration demanded a flight control hydraulic system of unprecedented power and performance. Increased system reliability, and reduced maintenance also presented a challenging system design. The YF-23A's unique flight and maneuvering envelope required high surface rates and large actuator excursions at low flight speeds, as well as power to generate increased hinge moments at supersonic speeds. To achieve these specifications, Northrop developed a hydraulic system that utilized flow conservation and prioritization techniques. The hydraulic system configuration was maintained by using hydrologic, as well as electronic control.

The X-29A aircraft is a fascinating combination of integrated technologies incorporated into a unique research aircraft. The X-29A program is a multiple-agency program with management and other responsibilities divided among the National Aeronautics and Space Administration (NASA), the Defense Advanced Research Projects Agency (DARPA), the U.S. Air Force, and the Grumman Corporation. This paper presents an overview of the recently completed X-29A flight research program, the objectives achieved to date, and a discussion of the future of the flight research program. Also discussed are the flight test approach expanding the envelope, typical flight maneuvers performed, X-29A program accomplishments, lessons learned for the Number One aircraft, and future plans with the Number Two aircraft. A schedule for both the Number One and Number Two aircraft is presented.

The AS6224 specification covers environment resistant, permanent insulation repair sleeves for repairing different types of insulation damages of wire or cable jackets in installed applications. The repair sleeve is intended to repair damaged primary wire or cable jacket covers where the shielding and wire conductors are not damaged.

The first flight of a delta wing aircraft took place in the United States at the Muroc AFB Flight Test Center on 18 September 1948. The aircraft, Convair No. 7002, Air Force S/N 46-682 and designated the XF-92A was piloted by Convair's Manager of Flight Research, E.D. “Sam” Shannon. The author witnessed this historic flight as a Flight Test Engineer on the project. Studies and wind tunnel tests for a supersonic interceptor were conducted at the Vultee Division of Consolidated Vultee Aircraft Corporation (Convair) in 1945. These studies led to the selection of the 60° delta wing plan form. This paper reviews the major differences between the thin wing XF-92A and the thick wing DM-1 glider (never flown) designed by Alexander M. Lippisch in Germany at the close of World War II. The XF-92A used a fully hydraulic irreversible control system for its elevons and rudder. The only airplanes up to this time with fully hydraulic controls were the Northrop XB-35 and the YB-49 flying wings.

AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment, and in interconnection systems.

AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment, and in interconnection systems.

AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic, and communication equipment, and in interconnection systems.

AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment, and in interconnection systems.

This specification covers tools used to install tiedown straps on wire bundles and for installing connector accessory shield termination bands (see 6.1).

This specification covers tools used to install tiedown straps on wire bundles and for installing connector accessory shield termination bands (see 6.1).

This specification covers three types of uncoated, square (0.050 to 0.500 inches in width), high-carbon steel wire (see 6.1).

This specification covers three types of uncoated, square (0.050 to 0.500 inches in width), high-carbon steel wire (see 6.1).