Search Results

THIS STANDARD ESTABLISHES THE DIMENSIONAL AND VISUAL QUALITY REQUIREMENTS, LOT REQUIREMENTS, AND PACKAGING AND LABELING REQUIREMENTS FOR D-RINGS MOLDED FROM MIL-P-25732 ACRYLONITRILE BUTADIENE (NBR) RUBBER. IT SHALL BE USED FOR PROCUREMENT PURPOSES.

RADIATION can produce almost instantaneous failure of modern aircraft lubricants, tests at Southwest Research Institute show. Two types of failures demonstrated are rapid viscosity rise and loss of heat conductivity. Furthermore, it was found that lubricants can become excessively corrosive under high-level radiation. Generally speaking, the better lubricants appeared to improve in performance while marginal ones deteriorated to a greater extent under radiation. When the better lubricants were subjected to static irradiation prior to the deposition test, there was a minor increase in deposition number as the total dose was increased.

This specification covers the requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating.

This specification covers the engineering requirements for electrodepositton of zinc and the properties of the deposit.

The YF-23A Advanced Tactical prototype Fighter was a revolutionary statically unstable, twin engine aircraft that cruised at supersonic speeds without afterburner and was designed to out maneuver opponents at subsonic and supersonic speeds. Combining these capabilities into a chosen aircraft configuration demanded a flight control hydraulic system of unprecedented power and performance. Increased system reliability, and reduced maintenance also presented a challenging system design. The YF-23A's unique flight and maneuvering envelope required high surface rates and large actuator excursions at low flight speeds, as well as power to generate increased hinge moments at supersonic speeds. To achieve these specifications, Northrop developed a hydraulic system that utilized flow conservation and prioritization techniques. The hydraulic system configuration was maintained by using hydrologic, as well as electronic control.

The Reflection Grating Spectrometer experiment (RGS) on the ESA corner stone X-Ray Multi-Mirror Mission (XMM) uses charge coupled devices (CCD) as detectors. Thermal requirements are the main driver for the layout of the detector housing. Parasitic heat inputs stem primarily from radiative coupling and from conduction over the structural support. Improvements in the design of the electro optical model (EOM) over the bread board model (BBM) resulted in a system that guarantees a CCD temperature of -130 °C at the end of the mission while not precluding the possibility to heat the detectors as high as +130°C which might be useful for annealing the CCDs.

This SAE Aerospace Standard (AS) covers 6-point and 12-point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box end and flare nut wrenches, combination open end and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) non-distorting usage; (b) possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 and ISO 8434-2; and (c) transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers 12-point open box end crowfoot, flare nut, double open box end, combination box and open box end, and ratcheting open box end wrenches that are designed with the following requirements: a Nondistorting usage b Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514. c Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers 12 point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: a. Non-distorting usage b. Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514. c. Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers 12 point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) Non-distorting usage; (b) Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514; (c) Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.

This SAE Aerospace Standard (AS) covers high strength thin wall (commercial) sockets, universal sockets, box wrenches and torque adaptors which possess the strength, clearances, and internal wrenching design so configured that, when mated with 12-point fasteners conforming to the requirement of AS870, they shall transmit torque to the fastener without bearing on the outer 5% of the fastener's wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes. The dimensional limits of box and combination wrench lengths have been established to provide configuration control for tool storage applications.

This SAE Aerospace Standard (AS) covers high strength thin wall (commercial) sockets, universal sockets, box wrenches and torque adaptors which possess the strength, clearances, and internal wrenching design so configured that, when mated with 12-point fasteners conforming to the requirement of AS870, they shall transmit torque to the fastener without bearing on the outer 5% of the fastener's wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes. The dimensional limits of box and combination wrench lengths have been established to provide configuration control for tool storage applications.