Search Results

This recommended practice covers visible surface defects on aerospace hose assemblies which have been installed and are functioning within a working environment at the time of visual inspection.

This recommended practice covers visible surface defects on aerospace hose assemblies which have been installed and are functioning within a working environment at the time of visual inspection.

This index of trademarks of current and former manufacturers of aerospace fittings, couplings, hoses, and tube support devices is within the scope of activities of the SAE G-3 Committee and available at the time of publication. Supplier markings from previous publication are maintained for component traceability. Suggestions for additional entries or corrections shall be sent to SAE in Warrendale, PA.

This Aerospace Recommended Practice (ARP) is intended to establish recommended installation torque value limits and test criteria for machined flared and flareless hose and tube end fitting connections. Assembly of bite-type MS21922 flareless sleeves is not included in this ARP (see MIL-F-18280). This ARP is applicable to two types of connections and two basic material classifications.

This SAE Aerospace Standard (AS) specifies test methods for fitting assemblies used in aircraft fluid systems in the pressure classes B, D, and E, and in temperature Types I, II, and III of MA 2001. This document applies each time that it is referred to in a procurement specification or other definition document. Fluids and materials used for the tests are listed in Section 2.

This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10500 kPa), D (3000 psi or 21000 kPa), E (4000 psi or 28000 kPa), and J (5000 psi or 35000 kPa) and in temperature types I (-65 to 160 °F or -55 to 70 °C), II (-65 to 275 °F or -55 to 135 °C), and III (-65 to 400 °F or -55 to 200 °C) of AS2001. This document applies each time that it is referred to in a procurement specification or other definition document. Fluids and materials used for the tests are listed in Section 2.

This SAE Aerospace Standard (AS) specifies test methods for tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10500 kPa), D (3000 psi or 21000 kPa), E (4000 psi or 28000 kPa), and J (5000 psi or 35000 kPa) and in temperature types I (-65 to 160 °F or -55 to 70 °C), II (-65 to 275 °F or -55 to 135 °C), and III (-65 to 400 °F or -55 to 200 °C) of AS2001. This document applies each time that it is referred to in a procurement specification or other definition document. Fluids and materials used for the tests are listed in Section 2.

This SAE Aerospace Information Report (AIR) establishes the specifications and descriptions of the critical components and operational guidelines for the standard hydraulic impulse machine for testing hydraulic hose assemblies, tubing, coils, fittings and similar fluid system components. This revision to the AIR1228 provides a description of a system that meets the requirements for specifications including: AS603, AS4265, and ARP1383. This impulse system utilizes closed loop servo control with specifically generated command signal waveforms. Data accuracy and integrity are emphasized in this revision. Knowing the uncertainty of the pressure measurement is important whether using a resonator tube system, as described in the original release of this document, or a closed-loop systems as described in this release. The accuracy of the data measurement system and consistency of the pressure waveform are fundamental to test validity, regardless of the system type.

This SAE Aerospace Information Report (AIR) establishes the part numbers and/or description of the critical components and operational guidelines for the standard hydraulic impulse machine for testing hydraulic hose assemblies, tubing, coils, and fittings and may be used for similar fluid system components, if desired. The standard impulse machine is established for the following purposes: 1 As referee in the event of conflicting data from two or more nonstandard impulse machines. Such a referee machine might be built by an impartial testing activity. 2 A design guide for future machines being built by manufacturers and users, or the upgrading of present machines. 3 A design guide for higher pressure machines or special purpose machines being designed. It is not the intention of this document to obsolete present machines.

This document establishes the requirements for a dry film lubricant AS6449 lubricant for use on breathing oxygen system and potable water system components, for a temperature range of -90 to +300 °F. This document also establishes the Non-Destructive Test (NDT) procedures and criteria for coated production parts. This document requires qualified products and product applicators.

This document establishes the requirements for a dry film lubricant AS6449 lubricant for use on breathing oxygen system and potable water system components, for a tempersture range of -90 °F to +300 °F. This document also establishes the Non-Destructive Test (NDT) procedures and criteria for coated production parts. This document requires qualified products and product applicators.

This document establishes the requirements for a dry film lubricant AS6449 lubricant for use on breathing oxygen system and potable water system components, for a tempersture range of −90 to +300 °F. This document also establishes the Non-Destructive Test (NDT) procedures and criteria for coated production parts. This document requires qualified products and product applicators.

This document establishes the requirements for a dry film lubricant AS6449 lubricant for use on breathing oxygen system and potable water system components, for a temperature range of -90 to +300 °F. This document also establishes the Non-Destructive Test (NDT) procedures and criteria for coated production parts. This document requires qualified products and product applicators.

This document establishes the requirements for a dry film lubricant AS6449 lubricant for use on breathing oxygen system and potable water system components, for a temperature range of −90 to +300 °F. This document also establishes the Non-Destructive Test (NDT) procedures and criteria for coated production parts. This document requires qualified products and product applicators.