Refine Your Search

Date

Date

Topic

Topic

Pistons Optics Tests and Testing Aerodynamics Aerospace Control systems AGE-3 Aircraft Ground Support Equipment Committee Identification

Search Results

Viewing 1 to 20 of 55
123Next >Last >>
Sort by title
Standard

Technical Manual Development for Ground Support Equipment
2002-07-23
HISTORICAL
AS4828
This document shall serve as a guide for format, style, and method of presentation for all material included in manufacturers' publications for ground support equipment (GSE). These requirements shall be observed throughout all publications except where modified by detail requirements for specific publications. AS4828 is not applicable to the development or revision of electronic test equipment user manuals and documents. This document is written in general terms by intention, and in most cases conform to recognized practices in the industry. In the event there is a question which is not specifically covered by this document, the user engineering department should be contacted for guidance before proceeding to the final phase of manual development. Each manual prepared by a manufacturer shall contain an introduction which shall include a brief statement explaining the organization, content, and method for using the manual.
Standard

Passenger Access Means Docking Indicator for Cabin Crew
2022-05-02
CURRENT
AS7995
This SAE Aerospace Standard describes the system used by passenger boarding stairs (PBS) mobile passenger boarding ramps (PBS) and boarding bridges (PBB) to inform on-board cabin crew about the docking status of the PBS/PBR/PBB and whether it is positioned such that it is safe to open the aircraft door. Current practice calls for the PBS/PBR/PBB operator to knock on the aircraft door to inform the cabin crew that it is safe to open the aircraft door. New technologies being incorporated into PBS/PBR/PBB such as remote control systems and autonomous driving vehicles are entering the market. As such, new/updated controls and/or procedures are necessary to ensure continuing safe operations.
Standard

Pallet/Container Loader Auto-Levelling Systems
2021-09-30
CURRENT
ARP4776
The data in this document is, at this stage, primarily concerned with the interface of pallet/container loaders and lower-deck compartments of standard and wide-body aircraft although the principles illustrated may be applied to the main-decks of narrow and wide-body aircraft. NOTE: For the purpose of this document, in accordance with Part 3 of the Directives for the technical work of ISO and with accepted IATA practice, minimum essential criteria defined by the word "shall" are absolute requirements. Recommended criteria identified by the word "should", while considered important, are not mandatory.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2005-02-10
HISTORICAL
ARP5283
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2012-09-24
HISTORICAL
ARP5283A
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
Standard

Method of Testing Pre-Conditioned Air Equipment
2021-04-08
CURRENT
ARP5374B
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

Method of Testing Pre-Conditioned Air Equipment
2008-04-15
HISTORICAL
ARP5374A
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

Method of Testing Pre-Conditioned Air Equipment
2001-12-07
HISTORICAL
ARP5374
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

Method of Evaluating Pneumatic Ground Power Units
2003-11-21
HISTORICAL
AIR4545
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
Standard

Measurement of Exterior Sound Level of Specialized Aircraft Ground Support Equipment
2006-10-13
HISTORICAL
ARP1801
The scope of this recommended practice covers specialized internal combustion engine powered equipment used in the support of aircraft operations. The equipment may be self-propelled, truck mounted, trailer mounted, skid mounted or stationary. It does not include construction equipment or equipment designed primarily for operation on highways or within factories or building areas.
Standard

Measurement of Exterior Sound Level of Specialized Aircraft Ground Support Equipment
2021-09-30
CURRENT
ARP1801A
The scope of this SAE Recommended Practice covers specialized internal combustion engine powered equipment used in support of aircraft operations. The equipment may be self-propelled, truck mounted, trailer mounted, skid mounted or stationary. It does not include construction equipment or equipment designed primarily for operation on highways or within factories or building areas. NOTE: Equivalent methodology is provided in (CEN) EN 1915-4, Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction, to be used for measurements conforming to the EU Machinery Directive
Standard

Maintenance of Batteries and Battery Charging and Servicing Facilities
2020-09-23
CURRENT
AIR1898A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/ maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

Impulse Towing Loads
2023-04-03
CURRENT
AIR6906
This SAE Aerospace Information Report (AIR) provides information about impulse loads that occur during normal aircraft towing operations. An instrumented tow bar was used to characterize towing loads. Suggestions to minimize impulse loads by reducing the tow bar to tow vehicle gap are described.
123Next >Last >>
X