Search Results

The SI-engine has a disadvantage in fuel economy compared with a DI-Diesel engine. One of the major effects is the throttle-driven load control with its pumping losses. The main target is to reduce these losses in the thermodynamic process with a throttle-free load control. BMW has developed fully variable valve trains as a possible technical solution to realise a load control by regulating the valve lift and the closing time of the inlet valve. The essential variability can be achieved by fully variable mechanical valve trains or mechatronic systems both showing a robust running behavior in emissions and cyclic fluctuations. The camshaft driven mechanical system is based on the technology of the BMW Double-VANOS system. An additional variability makes it possible to shift the valve lift continuously in order to control the valve closing. The highest variability is given by a system with each valve being controlled seperatly.

Modern exhaust systems contain not only a piping network to transport hot gas from the engine to the atmosphere, but also functional components such as the catalytic converter and turbocharger. The turbocharger is common place in the automotive industry due to their capability to increase the specific power output of reciprocating engines. As the exhaust system is a main heat source for the under body of the vehicle and the turbocharger is located within the engine bay, it is imperative that accurate surface temperatures are achieved. A study by K. Haehndel [1] implemented a 1D fluid stream as a replacement to solving 3D fluid dynamics of the internal exhaust flow. To incorporate the 3D effects of internal fluid flow, augmented Nusselt correlations were used to produce heat transfer coefficients. It was found that the developed correlations for the exhaust system did not adequately represent the heat transfer of the turbocharger.

The thermal prediction of a vehicle under-body environment is of high importance in the design, optimization and management of vehicle power systems. Within the pre-development phase of a vehicle's production process, it is important to understand and determine regions of high thermally induced stress within critical under-body components. Therefore allowing engineers to modify the design or alter component material characteristics before the manufacture of hardware. As the exhaust system is one of the primary heat sources in a vehicle's under-body environment, it is vital to predict the thermal fluctuation of surface temperatures along corresponding exhaust components in order to achieve the correct thermal representation of the overall under-body heat transfer. This paper explores a new method for achieving higher accuracy exhaust surface temperature predictions.

A test center for aging analysis and characterization of Lithium-Ion batteries for automotive applications is optimized by means of a dedicated cell tester. The new power tester offers high current magnitude with fast rise time in order to generate arbitrary charge and discharge waveforms, which are identical to real power net signals in vehicles. Upcoming hybrid and electrical cars show fast current transients due to the implemented power electronics like inverter or DC/DC converter. The various test procedures consider single and coupled effects from current profile, state of charge and temperature. They are simultaneously applied on several cells in order to derive statistical significance. Comprehensive safely functions on both the hardware and the software level ensure proper operation of the complex system.

A top-of-the-range car customer not only expects exceptional vehicle design and quality but also a driving experience, which is out of the ordinary. Very harmonious interaction between vehicle dynamics and the steering system is required to offer clients such a consistent driving experience through generations of vehicle models. In this paper the basic properties of a premium driving experience are explored. It is shown that outstanding handling limits are a prerequisite, although most customers never experience such driving situations. In fact, on-center behavior is most crucial in enabling clients to experience part of premium driving performance, and the steering system is the key factor in delivering appropriate feedback to the driver by means of steering torque. Development procedures are presented to achieve the goals described above.

Wind noise is a significant source of interior noise in automobiles at cruising conditions, potentially creating dissatisfaction with vehicle quality. While wind noise contributions at higher frequencies usually originate with transmission through greenhouse panels and sealing, the contribution coming from the underbody area often dominates the interior noise spectrum at lower frequencies. Continued pressure to reduce fuel consumption in new designs is causing more emphasis on aerodynamic performance, to reduce drag by careful management of underbody airflow at cruise. Simulation of this airflow by Computational Fluid Dynamics (CFD) tools allows early optimization of underbody shapes before expensive hardware prototypes are feasible. By combining unsteady CFD-predicted loads on the underbody panels with a structural acoustic model of the vehicle, underbody wind noise transmission could be considered in the early design phases.

Uncertainties play a major role in vibroacoustics - especially in car body design in the preliminary development because of the overall spread in the production that should be covered with one simulation model. Therefore, we use uncertain input parameters to determine the stochastically distributed admittance of the car body before each part of the car is fully designed. To gain a stochastic result - the stochastically distributed admittance curve - we calculate a deterministic finite element simulation several times with sets of stochastically distributed input parameter values. To reduce simulation time and cost of the car model with many million degrees of freedom we focus on the uncertain parameters that show a significant influence on the admittance curve. It is therefore necessary to be able to accurately estimate for each parameter if its influence on the admittance of the car body plays a major role for the noise vibration harshness simulation.

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

The spray-guided BMW DI combustion system eliminates the most important disadvantages of the wall-and air-guided 1st generation DI combustion systems. With its central injector position, the spray-guided system provides a stratified mixture at the spark plug and reduces wall wetting significantly. The low spray penetration and high spray stability of the outward-opening piezo injector allow an extension of the stratified engine map to higher engine load and speed. The piezo drive permits an extremely fast opening of the injector needle, thus enabling multiple injections with very short delay times and high flexibility for the calibration strategy to supply a very efficient combustion with low unburnt hydrocarbon and carbon monoxide emissions. Compared to a conventional throttled SI engine, the spray-guided system shows a fuel consumption potential of about 20% in the NEDC.

Future catalyst systems need to be highly efficient in a limited packaging space. This normally leads to a design where the flow distribution, in front of the catalyst, is not perfectly uniform. Measurements on the flow test bench show that the implementation of perforated foils for the corrugated and flat foils has the capability to distribute the flow within the channels in the radial direction so that the maximum of the given catalyst surface is of use, even under very poor uniformity indices. Therefore a remarkable reduction in back pressure is measured. Emission results demonstrate cold start improvement due to reduced heat capacity. The use of LS - structured ( Longitudinal structured ) corrugated foils creates a high turbulence level within the single channels. The substrate lights-up earlier and the maximum conversion efficiency is reached more quickly.

In the near future the effort on the development of exhaust gas treatment systems must be increased to meet the stringent emission requirements. If the relevant physical and chemical models are available, the numerical simulation is an important tool for the design of these systems. This work presents a CFD model that allows to cover the full range of applications in this area. After a detailed presentation of the theoretical background and the modeling strategies results for the simulation of a close-coupled catalyst are shown. The presented model is also applied to the oxidation of nitrogen oxides, to a diesel particle filter and a fuel-cell reformer catalyst.

Eight partners from Europe and one from North America have joined efforts in a EU-supported project to find new ways for sustainable production of Mg-based engine blocks for cars. The ultimate aim of the work is to reduce vehicle weight, thereby reducing fuel consumption and CO2 emissions from operation of the vehicle. Four new magnesium alloys are considered in the project and an engine block has been series cast - 20 each in two alloys. An extensive mechanical testing program has been initiated to identify in particular the high temperature limits of the four alloys and a significant experimental study of proper bolt materials for joining is being done in parallel. Engine redesign and life cycle analysis has also been completed to secure the future sustainable exploitation of the project results. This paper presents an overview of the work and results obtained until now - 3 months before the ending date of the project.

Nowadays there is an increasing need to streamline CAE processes. One such process consists of translating a Multibody Dynamics System (MBS) model into an equivalent Finite Element Analysis (FEA) model. Typically, users start with the creation of a MBS model which is set at a desired operating point by means of running simulations in the MBS domain (e.g. dynamics, statics.) The MBS model is then further translated into an equivalent FEA model which is used to perform simulations in the FEA domain (e.g. passive safety/crash, noise vibration harshness/NVH.) Currently, the translation of the MBS model into a FEA model is done either manually or by means of using a user-written script. This paper shows that a user-written script that translates a MBS model into a FEA model can not provide a high fidelity translation. In general, it is found that eigenvalues computed by the FEA code would not match eigenvalues computed by the MBS code.

Substructuring approaches are helpful methods to solve and understand vibro-acoustic problems involving systems as complex as a vehicle. In that case, the whole system is split into smaller, simpler to solve, subsystems. Substructuring approaches allow mixing different modeling “solvers” (closed form solutions, numerical simulations or experiments). This permits to reach higher frequencies or to solve bigger systems. Finally, one of the most interesting features of substructuring approaches is the possibility to combine numerical and experimental descriptions of subsystems. The latter point is particularly interesting when dealing with subdomains that remain difficult to model with numerical tools (assembly, trim, sandwich panels, porous materials, etc.). The Patch Transfer Functions (PTF) method is one of these substructuring approaches. It condenses information (impedance matrix) of subsystems on their coupling surfaces.

Transfer path analyses of vehicle bodies are widely considered as an important tool in the noise, vibration and harshness design process, as they enable the identification of the dominating transfer paths in vibration problems. It is highly beneficial to model uncertain parameters in early development stages in order to account for possible variations on the final component design. Therefore, parameter studies are conducted in order to account for the sensitivities of the transfer paths with respect to the varying input parameters of the chassis components. To date, these studies are mainly conducted by performing sampling-based finite element simulations. In the scope of a sensitivity analysis or parameter studies, however, a large amount of large-scale finite element simulations is required, which leads to extremely high computational costs and time expenses. This contribution presents a method to drastically reduce the computational burden of typical sampling-based simulations.

As a key part of numerical analysis, the modeling process has a tremendous influence on the quality of the results. While there is general awareness concerning uncertainties that arise during modeling, their quantity and sensitivity rarely are known. Hence, modeling quickly can become inaccurate and inefficient. The scope of the present paper is to innovate predictive modeling processes concerning the dynamics of real complex structures by means of linear modal analysis with the finite element method (FEM). The aim is to offer a transparent design catalog relating specific uncertainties to each model component in order to achieve error prevention for engineers dealing with comparable systems. A complex system is simplified and investigated for different levels of detail. Only after the model uncertainties for one level of detail are obtained, the next level of complexity is approached.

Finite element simulation (FE) makes it possible to analyze the structural dynamic behavior of vehicle seat structures in early design phases to meet Noise-Vibration-Harshness (NVH) requirements. For this purpose, linear simulations are usually used, which neglect many nonlinear mechanical properties of the real structure. These models are trimmed to fit global vibration behavior based on the complex description of contact or jointed definitions. Targeted design is therefore only possible to a limited extent. The aim of this work is to characterize the entire seat structure and its sub-components in order to identify the main contributors using experimental and simulative data. The Lagrange Multiplier Frequency Based Substructuring (LM-FBS) method is used for this purpose. Therefore, the individual subsystems of seat frame, seat backrest and headrest are characterized under different conditions.

The Magnetic Forming Process is more than ever a very promising technology for light weight vehicle production. To support the development of further applications BMW Group has proven the ability of a standard FEM program to predict the process and the functional parameters of magnetically formed joints satisfactorily.

Classical decentralized architectures based on large networks of microprocessor-based Electronic Control Units (ECU), namely those used in self-driving cars and other highly-automated applications used in the automotive industry, are becoming more and more complex. These new, high computational power demand applications are constrained by limits on energy consumption, weight, and size of the embedded components. The adoption of new embedded centralized electrical/electronic (E/E) architectures based on dynamically reconfigurable hardware represents a new possibility to tackle these challenges. However, they also raise concerns and questions about their safety. Hence, an appropriate evaluation must be performed to guarantee that safety requirements resulting from an Automotive Safety Integrity Level (ASIL) according to the standard ISO 26262 are met. In this paper, a methodology for the evaluation of dynamically reconfigurable systems based on centralized architectures is presented.

BMW VALVETRONIC technology is able to maintain the most important measures to reduce emissions. The further optimized charge movement created by VALVETRONIC stabilizes the combustion in the catalyst heating mode with extremely retarded ignition timing. When the engine is warm the high residual gas tolerance ensures very low Engine-Out NOx emissions and at the same time a low level of hydrocarbons. The atomization of fuel droplets due to high flow velocity in the valve gap area leads to improved mixture formation and reduced wall wetting. Engine-Out HC emissions in a cold engine are therefore reduced. Combined, the emission measures achieve robust and efficient emission control. In combination with additional after-treatment like secondary air system and catalysts using high cell density VALVETRONIC engines form an excellent base for SULEV emission regulations without neglecting the typical BMW claim of efficient dynamics.