Search Results

Abstract The key issues of automatic emergency braking (AEB) control algorithm are when and how to brake. This article proposes an AEB control algorithm that integrates risk perception (RP) and emergency braking characteristics of professional drivers for rear-end collision avoidance. Using the formulated RP by time to collision (TTC) and time headway (THW), the brake trigger time can be determined. Based on the professional driver fitting (PDF) characteristic, the brake pattern can be developed. Through MATLAB/Simulink simulation platform, the European New Car Assessment Programme (Euro-NCAP) test scenarios are used to verify the proposed control algorithm. The simulation results show that compared with the TTC control algorithm, PDF control algorithm, and the integrated PDF and TTC control algorithm, the proposed integrated PDF and RP control algorithm has the best performance, which can not only ensure safety and brake comfort, but also improve the road resource utilization rate.

Abstract This article investigates the dynamics of non-smooth and nonlinear oscillations of a bicycle-car model, considering the tire-road separation. Road contact applies a non-holonomic constrain on the dynamics system that makes the equations of motion to be different under in-contact and off-contact conditions. The set of nonlinear equations of the system has been formulated based on nondimensionalization to minimize the number of parameters and generalize the results. To compare the quality of different suspensions in reducing the unpleasant no-contact conditions, we define a contact-free fraction indicator to measure the separation fraction time during a cycle of steady-state oscillation. An observation of frequency responses including vertical displacements, the pitch mode, and the domain of contact-free fraction of time has been investigated to clarify engineering design directions.

Abstract When the vehicle is under braking condition in the longitudinal motion, the vehicle body will tilt due to the inertial force in motion. A high amplitude will result in uncomfortable feelings of the occupant, such as nervousness or dizziness. To solve the problem, this article presents an adaptive damping system (ADS), which combines the vehicle anti-pitch compensation control with the mixed skyhook (SH) and acceleration-driven-damper (ADD) control algorithm. This ADS can not only improve the vibration effect of the vertical motion for the vehicle but also consider the longitudinal motion of the vehicle body. In addition, a new damper mechanical hardware-in-the-loop test bench is built to verify the effectiveness of the algorithm.

Abstract A critical component of vehicle dynamic control systems is the accurate and real-time knowledge of the vehicle’s key states and parameters when running on the road. Such knowledge is also essential for vehicle closed-loop feedback control. Vehicle state and parameter estimation has gradually become an important way to soft-sense some variables that are difficult to measure directly using general sensors. In this work, a seven degrees-of-freedom (7-DOF) nonlinear vehicle dynamics model is established, where consideration of the Magic formula tire model allows us to estimate several vehicle key states using a hybrid algorithm containing an unscented Kalman filter (UKF) and a genetic algorithm (GA). An estimator based on the hybrid algorithm is compared with an estimator based on just a UKF. The results show that the proposed estimator has higher accuracy and fewer computation requirements than the UKF estimator.

Abstract In this article, a hierarchical coordinated control algorithm for integrating active rear steering and driving/braking force distribution (ARS+D/BFD) was presented. The upper-level control was synthesized to generate the required rear steering angle and external yaw moment by using a sliding-mode controller. In the lower-level controller, a control allocation algorithm considering driving/braking actuators and tire forces constraints was designed to assign the desired yaw moment to the four wheels. To this end, an optimization problem including several equality and inequality constraints were defined and solved analytically. Finally, computer simulation results suggest that the proposed hierarchical control scheme was able to help to achieve substantial enhancements in handling performance and stability.

Abstract Advanced passenger vehicles are complex dynamic systems that are equipped with several actuators, possibly including differential braking, active steering, and semi-active or active suspensions. The simultaneous use of several actuators for integrated vehicle motion control has been a topic of great interest in literature. To facilitate this, a technique known as control allocation (CA) has been employed. CA is a technique that enables the coordination of various actuators of a system. One of the main challenges in the study of CA has been the representation of actuator dynamics in the optimal CA problem (OCAP). Using model predictive control allocation (MPCA), this problem has been addressed. Furthermore, the actual dynamics of actuators may vary over the lifespan of the system due to factors such as wear, lack of maintenance, etc. Therefore, it is further required to compensate for any mismatches between the actual actuator parameters and those used in the OCAP.

Abstract Throughout the automobile industry, the electronic brake boost technologies have been widely applied to support the expansion of the using range of the driver assist technologies. The electronic brake booster (EBB) supports to precisely operate the brakes as necessary via building up the brake pressure faster than the vacuum brake booster. Therefore, in this article a novel control strategy for the EBB based on fuzzy logic control (FLC) is developed and studied. The configuration of the EBB is established and the system model including the permanent magnet synchronous motor (PMSM), a two-stage reduction transmission (gears and a ball screw), a servo body, reaction disk, and the hydraulic load are modeled by MATLAB/Simulink. The load-dependent friction has been compensated by using Karnopp friction model. Due to the strong nonlinearity on the EBB components and the load-dependent friction, FLC has been used for the control algorithm.

Abstract The automotive industry offers many applications for machine learning (ML), in general, and deep neural networks in particular. However, the real-world deployment of neural networks into safety-critical components remains a challenge as models would need to offer robustness under a wide range of operating conditions. In this work, we focus on uncertainty estimation, which can be used to deliver predictors that fail gracefully, by detecting situations where their predictions are unreliable. Following Gräber et al. [1], we use Recurrent Neural Networks (RNNs) to perform sideslip angle estimation. To perform robust uncertainty estimation, we augment the RNNs with generative models. We demonstrate the advantage of the proposed model architecture over Monte Carlo (MC) dropout [2] on the Revs data set [3].

Abstract The external driving environment of an autonomous driving vehicle is complex and changeable. In this article, the trajectory tracking control with obstacle avoidance based on model predictive control was presented. Specifically, double-level control scheme by controlling the front steering angle was used in our research, and the double level is composed of the high level of model predictive controller for local trajectory planning and low level of model predictive controller for trajectory tracking. At high level, the local trajectory planner based on the point-mass model was designed. Then, at low level, the linear time-varying vehicle dynamics model was presented, and the trajectory tracking controller was proposed considering control variable, control increment, and output constraint. Finally, the trajectory tracking performance was tested in co-simulation environment with CarSim and Simulink, and the tracking errors were analyzed.

Abstract This article introduces a finite element (FE) approach to determine tire deformation and its effect on open-wheel race car aerodynamics at high vehicle velocities. In recent literature tire deformation was measured optically. Combined loads like accelerating at a corner exit are difficult to reproduce in wind tunnels and require several optical devices to measure the tire deformation. In contrast, an FE approach is capable of determining the tire deformation in combined load states accurately. Additionally, the temperature influence on tire deformation is investigated. The FE tire model was validated using three-dimensional (3D) scan measurements; stiffness measurements in the vertical, lateral, and longitudinal direction; and the change of loaded radius with speed at different loads, respectively. The deformed shape of the tire of the FE model was used in a computational fluid dynamics (CFD) simulation.

Abstract To investigate the effect of a tire blowout (TBO) on the dynamics of the vehicle comprehensively, a three-dimensional full-vehicle multibody mathematical model is developed and integrated with the nonlinear Dugoff’s tire model. In order to ensure the validity of the developed model, a series of standard maneuvers is carried out and the resulting response is verified using the high-fidelity MSC Adams package. Consequently, the in-plane, as well as out-of-plane dynamics of the vehicle, is extensively examined through a sequence of TBO scenarios with various blown tires and during both rectilinear and curvilinear motion. Moreover, the different possible inputs from the driver, the road bank angle, and the antiroll bar have been accounted for. The results show that the dynamic behavior of the vehicle is tremendously affected both in-plane and out-of-plane and its directional stability is degraded.

Abstract The brake discs are subjected to thermal load due to sliding by the brake pad and fluctuating loads because of the braking load. This combined loading problem requires simulation using coupled thermo-mechanical analysis for design evaluation. This work presents a combined thermal and mechanical finite element analysis (FEA) and evolutionary optimization-based novel approach for estimating the optimal design parameters of the ventilated brake disc. Five parameters controlling the design: inboard plate thickness, outboard plate thickness, vane height, effective offset, and center hole radius were considered, and simulation runs were planned. A total of 27 brake disc designs with design parameters as recommended by the Taguchi method (L27) were modeled using SolidWorks, and the FEA simulation runs were carried out using the ANSYS thermal and structural analysis tool.

Abstract Pyrotechnic seat belt pretensioners typically remove 8–15 cm of belt slack and help couple an occupant to the seat. Our study investigated pretensioner deployment on forward-leaning, live volunteers. The forward-leaning position was chosen because research indicates that passengers frequently depart from a standard sitting position. Characteristics of the 3D kinematics of forward-leaning volunteers following pretensioner deployment determines if body size is correlated with subject response. Nine adult subjects (three female), ages 18–43 years old, across a wide range of body sizes (50–120 kg) were tested. The age was limited to young, active adults as pyrotechnic pretensioners can deliver a notable force to the trunk. Subjects assumed a forward-leaning position, with 26 cm between C7 and the headrest, in a laboratory setting that replicated the passenger seat of a vehicle.

Abstract Equal-channel angular pressing (ECAP) is among the most applicable severe plastic deformation processes used to fabricate ultrafine-grained materials with superior mechanical properties. In this work, a commercial purity aluminum has been processed via ECAP process up to four passes. The influence of ECAP routes (A and Bc) on the mechanical properties of the material and its grain size was investigated. Microstructural observations of the as-annealed and the rods processed via ECAP were undertaken using optical microscopy. Hardness profiles and contour maps of sections cut perpendicularly and parallel to the load direction were assessed to investigate the effect of ECAP processing on the hardness distribution across the deformed rods. Compressive properties of the rods were also examined. In addition, digital images correlation was used to display the stress distribution along the longitudinal section of the processed sample during the compression test.

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC