Search Results

Engines of commercial vehicles deliver significant amount of power (more than 25% of propulsive power) for non-propulsive loads such as air-conditioner, alternator, air compressor, radiator fan, steering oil pump, lights etc. Use of these auxiliaries cause sub-optimal utilization of engine power resulting in increased fuel consumption and emissions. A fuel cell powered auxiliary power unit (FC-APU) is proposed to isolate the auxiliaries from the engine. Use of FC-APU shall help improve load carrying capacity, gradeability, fuel efficiency and emissions of the vehicle. This paper describes a mathematical system level model developed using MATLAB-SIMULINK to estimate auxiliary power consumption and simulate FC-APU system. A statistical analysis is performed on the power consumed by various auxiliaries during different duty cycles. The data is used to propose a FC- APU system. Fuel cell is the most expensive component in the system.

Steering gear box function is one of the important requirements in heavy vehicles in order to reduce driver fatigue. Improper functioning of steering gear box not only increases the driver fatigue, also concerns the safety of the vehicle. In this present investigation, the engine oil mixing up with steering oil has been identified and steering gear box failure has been observed in the customer vehicle. The root cause of failure has been analyzed. Based on the investigations, in particular design of steering pump has been failed at customer end. The same design of steering pump were segregated and analyzed. Initial pressure mapping study has been conducted. The pressure mapping results revealed that the cavity pressure obstructs the flow of suction pressure. It indicates that obstacle at suction port due to the existence of internal leakage that causes back pressure in the internal cavity of steering pump which sucks engine oil.

A major activity of any new vehicle development program, is to meet legal requirements of local markets. Pass by noise (PBN) test is one of the standardized tests and is used to certify new vehicles/variants for their Noise emissions. Certification for noise emissions of commercial vehicles is achieved by measuring external sound levels according to procedures defined by standards such as IS: 3028 for Indian market. Before a physical proto-vehicle is assembled, various systems and subsystems are readily made available by suppliers off the shelf. During final design validation of the vehicle by mule-vehicle testing, PBN target compliance need be assured for all these systems in order to meet overall PBN target. The PBN on an Intermediate commercial vehicle (ICV) migrated to the latest Exhaust emission standard, was the subject of this study. This vehicle emitted PBN greater than accepted threshold.

E85 (85% Ethanol + 15% Gasoline), as an alternative fuel has been widely used in spark ignited engines used in light duty vehicles. However, they are rarely used in spark ignited heavy duty engines. In this study, we used E85 in a 5.8 litre, multi cylinder, turbocharged, multi point - port injected, spark ignited heavy duty engine, to analyze the performance capability. As E85 has higher octane rating, the compression ratio was increased to 11.5:1. Experimental investigation of In-cylinder pressure was done and the engine’s ignition timing and injection duration was calibrated to operate the engine below peak firing pressure limits, without knocking. The experimental results showed that exhaust gas recirculation resulted in lower peak firing pressure and rate of heat release. The results of the engine test showed that E85 can be used in heavy duty spark ignited engines. The scope for future work is on addressing the higher BSFC and cold start from subzero temperature levels.

The suspension system in a vehicle isolates the frame and body from road shocks and vibrations which would otherwise be transferred to the passengers and goods. Heavier goods vehicles use tandem axles at the rear for load carrying. Both the axles should be inter-connected to eliminate overloading of any one axle when this goes over a bump or a ditch. One of the inter-connecting mechanism used is leaf spring with tie rod, bell crank & linkages, when the first rear axle moves over a bump, the linkages equalize the loading on the second rear axle. This paper details about the failure analysis methodology to simulate the tie rod field failure using a six poster road simulator and to identify the root cause of the failure and further corrective actions.

Commercial vehicles have steering systems with one or more steering links connecting the steering gear box pitman arm and front axle steering arm. In case of twin steer vehicles, intermediate pivot arm is used to transfer the motion proportionately between the two front axles. Intermediate pivot arm is also used in some longer front over-hang vehicles to overcome their packaging constraints and to optimize the mechanical leverage. The pivot shaft is a mechanical part of the intermediate pivot arm assembly upon which pivot arm can swivel in one axis. Steering forces transferred through the drag links generates resultant forces and bending moments on the pivot shaft. In this work, study has been carried out on premature failure of the pivot shaft in city bus application model (Entry + 1 step). Metallurgical analysis of failed part indicated the failure to be due to fatigue. Pivot shaft was tested in rig with similar load conditions in order to replicate the failure.

In this paper, experimental evaluation was carried out on a 6.0 L heavy duty CNG engine which has been optimized for 18 percent hydrogen blended CNG (HCNG). Optimization test results shows that use of HCNG results in reduced CO, THC & CH4 emissions by 39, 25 & 25 percent respectively and increase in NOx by 32 percent vis-a-vis CNG. After optimization the engine was subjected to endurance test of 600 hours as per 15 mode engine simulated city driving cycle with HCNG. The performance & emission characteristics of the engine were analyzed after completion of every 100 hours as per European Transient Cycle (ETC). Test results indicate that there were no significant changes observed in engine power output over the complete endurance test of 600 hrs with HCNG. Specific fuel consumption (SFC) measurements were consistent at all the 15 modes of engine simulated city driving cycle.

Natural gas has been considered and implemented as alternative fuel to gasoline and diesel powered vehicles worldwide. Although natural gas belongs to petroleum fuel family, it has considerable recourses worldwide to ensure long energy security and comparatively lower carbon to hydrogen ratio that make it more environment friendly. This paper presents the effect of long duration endurance test on gas engine oil along with performance and emission characteristics of 5.8 L turbocharged heavy duty natural gas engine. The six cylinder engine was chosen due to its importance for urban bus transportation. The engine was subjected to long duration endurance test of 800 hrs with closed loop monitoring and controlled conditions as per 6 mode engine load cycle. During the complete endurance test of 800 hours, performance and emission characteristics of the engine were analyzed after completion of every 100 hours as per Full Throttle Performance Test and European Transient Cycle (ETC).

This case study involves the failure analysis of the wheel arch structure for a commercial truck. The wheel arch is an important vehicle trim aggregate from both the regulatory perspective (spray suppression) as well as from the aesthetics of the truck. But, the durability of this part is affected by the vehicle architecture, vehicle load capacity as well as the operating conditions. This is more critical due to the nature of the overhang experienced by the mounting bracket assemblies that hold these wheel arches/mud flaps. This generally consist of tubular and sheet metal welded structures bolted on to the main chassis long members. These failures were observed in a legacy vehicle, where very little details of the complete vehicle digital simulation and testing performance were readily available.

All automotive components undergo stringent testing protocol during the design validation phase. Nevertheless, there are certain components in the field which are seldom captured during design validation. One of these components is the battery isolator switch. This project aims at optimizing a validation methodology for this component based on field usage and conditions. The isolator switch is the main control switch which connects and disconnects the electrical loads from the battery. This switch is used in the electrical circuit of the vehicle to prevent unwanted draining of battery when it is not needed and when the vehicle is in switched off. An electrical version of this switch uses electromagnetic coils to short the contacts. The failure mode being investigated is a high current load causing the input and output terminal to be welded.

Tippers used for transporting blue metal, construction and mining material is designed with different types of load body to suit the material being carried, capacity and its application. These load bodies are constructed with high strength material to withstand forces under various operating conditions. Structural strength verification of load body using FEM is conducted, by modelling forces due to payload as a pressure function on the panels of the load body. The spatial variation of pressure is typically assumed. In discrete element method (DEM) granular payload material such as gravel, wet or dry sand, coal etc., can be modelled by accounting its flow and interaction with structure of load body for prediction of force/pressure distribution. In this paper, coupled FE-DEM is used for determining pressure distribution on loading surfaces of a tipper body structure of a heavy commercial vehicle during loading, unloading and transportation.

Diesel engine pollutants include Oxides of Nitrogen (NOx) and Particulate Matter (PM) which are traditionally known for their trade-off characteristics. It’s been a challenge to reduce both pollutants at the source simultaneously, except by efforts through low temperature combustion concepts. NOx formation is dependent on the combustion temperature and thus the in-cylinder reduction of NOx formation remains of utmost importance. In this regard, water injection into the intake of a heavy-duty diesel engine to reduce peak combustion temperature and thereby reducing NOx is found to be a promising technology. Current work involves the use of 1-D thermodynamic simulation using AVL BOOST for modeling the engine performance with water injection. Mixing Controlled Combustion (MCC) model was used which can model the emissions. Initially, the model validation without the water injector was carried out with experimental data.

A full-bodied validation of automotive system emphasis on a comprehensive coverage of failure modes of component on one hand and evaluation with full system for the intended function of single component on the other has for long been cumbersome to most commercial vehicle manufacturers. This paper focuses on optimizing the test method in rig testing to relieve the complexity in the structural validation as whole system level. The methodology proposed by authors focuses on accelerating the vibration testing of component by compressing the validation timelines by using CSCPV (Combined Systematic Calculated and Pre Validation) method. This method selects the components of the system for validation by VFTM (Vital Few and Trivial Many) approach from existing testing database failure data and selects the worst predominant failure cases. This CSCPV method uses systematically calculated representing mass from analysis to validate the intended component alone instead of entire system.

This paper describes a methodology for design and development of On-Board Diagnostic system (OBD) with an objective to improve current reliability process in order to ensure design & quality of the new system as per requirement of commercial vehicle technology. OBD is a system that detects failures which adversely affect emissions and illuminates a MIL (Malfunction Indicator Lamp) to inform the driver of a fault which may lead to increase in emissions. OBD provides standard and unrestricted access for diagnosis and repair. Below given Figure 1 shows the working principle of OBD system. The exhaust emission of a vehicle will be controlled primarily by Engine Control Unit (ECU) and Exhaust Gas After Treatment Control (EGAS CU). These two control units determine the combined operating strategies of the engine and after treatment device. Figure 1 Modern Control Architecture for OBD System in Commercial vehicle [1]

The modern day automobile customers’ expectations are sky-high. The automotive manufacturers need to provide sophisticated, cost-effective comfort to stay in this competitive world. Air conditioning is one of the major features which provides a better comfort but also adds up to the increase in operating fuel cost of vehicle. According to the sources the efficiency of internal combustion engine is 30% and 70% of energy is wasted to atmosphere. The current Air conditioners in automobiles use Vapour compression system (VCS) which utilizes a portion of shaft power of the engine at its input; this in turn reduces the brake power output and increases the specific fuel consumption (SFC) of the engine. With the current depletion rate of fossil fuels, it is necessary to conserve the available resources and use it effectively which also contributes to maintain a good balance in greenhouse effect thus protecting the environment.

Transfer function measurements are the basis for construction of conventional test based source-path-receiver model of a vehicle. Interior noise of a vehicle can be synthesized using source excitation (both acceleration at source and near source sound pressure level) and its corresponding transfer function (Vibro-Acoustic Transfer Function (VATF) and Acoustic Transfer Function (ATF) respectively) to the interior of vehicle. Ideally ATF should be linear and independent of sound source, dependent only on size of air cavities, body structure and its material characteristics in between receiver and source location. But practically because of the type of excitation signal used to excite the sound source and characteristics of sound source itself, there is a possibility of variations in amplitude of acoustic transfer function.

The commercial vehicle industry is evolving faster with the rise in multifarious aspects deciding a company's progress. In the current scenario, vehicle performance and its reliability in the areas of payload, fuel economy, etc. play vital roles in determining its sustenance in the industry, in addition to reducing driver fatigue and improving comfort levels. Test quality and time is the key to assure and affirm, smooth and quick launch of the product into the market. This paper details on the design of Multi-Axis road data simulator which entails realistic loads onto the components for capturing meaningful information on behavior of the product and recreate the field failure modes. The design was conceptualized keeping in mind both cost (for initial installation and running cost) and time for testing without loss in the convergence factor.