Search Results

As part of its educational experience, the Noise & Vibration Conference begins with focused instructor-led workshops designed for those new to NVH or those looking for a refresher on a given topic.

Work solenoids are widely used in household appliances. The environment and design of this type application does not lead to solenoids for the earthmoving industry. This paper presents the environmental effects to be considered when designing a solenoid for the earthmoving industry. It further explains the need for, and type of, test necessary to validate the design. Finally a review of production quality procedures, necessary to insure reliable production parts is discussed.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on construction, agricultural, and general purpose industrial categories of off-road self-propelled work machines as defined in SAE J1116.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on construction, agricultural, and general purpose industrial categories of off-road self-propelled work machines as defined in SAE J1116.

Knitted wiremesh along with radial gas tight seals provide reliable mounting system for low temperature underbody converters. The compression characteristics of the wiremesh is modified by wire material, wire diameter, wire geometry, mesh crimp heights; wire density, wiremesh courses per inch, needle count, number of strands, wiremesh temper, wiremesh surface profile and surface characteristics. The radial mounting pressure provided by the wiremesh is matched with the mounting pressure requirement. Wiremesh systems can be tailored to any required radial mounting pressure from conventional to ultra thin-wall substrates. The wiremesh mounting system is proven durable, without any failure on more than 25 million underbody converters in light duty vehicles. Cp and Cpk show the capability of the manufacturing process. Thus the wiremesh mounting support is a viable alternate for low temperature gasoline and diesel applications.

To investigate the feasibility of various test procedures to determine aerodynamic performance for the Phase 2 Greenhouse Gas (GHG) Regulations for Heavy-Duty Vehicles in the United States, the US Environmental Protection Agency commissioned, through Southwest Research Institute, constant-speed torque tests of several heavy-duty tractors matched to a conventional 53-foot dry-van trailer. Torque was measured at the transmission output shaft and, for most tests, also on each of the drive wheels. Air speed was measured onboard the vehicle, and wind conditions were measured using a weather station placed along the road side. Tests were performed on a rural road in Texas. Measuring wind-averaged drag from on-road tests has historically been a challenge. By collecting data in various wind conditions at multiple speeds over multiple days, a regression-based method was developed to estimate wind-averaged drag with a low precision error for multiple tractor-trailer combinations.

A 1:10-scale wind tunnel development program was undertaken by the National Research Council of Canada and Airshield Inc. in 1994 to develop trailer side skirts that would reduce the aerodynamic drag of single and tandem trailers. Additionally, a second wind tunnel program was performed by the NRC to evaluate the fuel-saving performance of boat-tail panels when used in conjunction with the skirt-equipped single and tandem trailers. Side skirts on tandem, 8.2-m-long trailers (all model dimensions converted to full scale) were found to reduce the wind-averaged drag coefficient at 105 km/h (65 mi/h) by 0.0758. The front pair of skirts alone produced 75% of the total drag reduction from both sets of skirts and the rear pair alone produced 40% of that from both pairs. The sum of the drag reductions from front and rear skirts separately was 115% of that when both sets were fitted, suggesting an interaction between both.

A wind tunnel experiment has been conducted to determine the changes in drag and side force due to the presence and position of cab extenders on a model of a commercial tractor-trailer truck. The geometric variables investigated are the cab extenders angle of incidence, the tractor-trailer spacing and the yaw angle of the vehicle. Three cab extender angles were tested-0°, 15° (out) and -15° (in) with respect to the side of the tractor. The cab and trailer models have the same width and height. The minimum drag coefficient was found for the tractor and trailer combination when the cab extenders were set to 0° angle of incidence with respect to the headwind. This result holds for all yaw angles with moderate gap spacing between the tractor and trailer. This study suggests that commercial tractor-trailer trucks can benefit from adjustable cab extender settings; 0° when using a trailer and -15° when no trailer is used.

The use of devices to reduce aerodynamic drag on large trailers and save fuel in long-haul, over-the-road freight operations has spurred innovation and prompted some trucking fleets to use them in combinations to achieve even greater gains in fuel-efficiency. This paper examines aerodynamic performance and potential drag reduction benefits of using trailer aerodynamic components in combinations based upon wind tunnel test data. Representations of SmartWay-verified trailer aerodynamic components were tested on a one-eighth scale model of a class 8 sleeper tractor and a fifty three foot, van trailer model. The open-jet wind tunnel employed a rolling floor to reduce floor boundary layer interference. The drag impacts of aerodynamic packages are evaluated for both van and refrigerated trailers. Additionally, the interactions between individual aerodynamic devices is investigated.

The trucking industry is being encouraged by environmental and cost factors to improve fuel efficiency. One factor that affects fuel efficiency is the aerodynamic design of the vehicles; that is, the vehicles with lower aerodynamic drag will get better mileage, reducing carbon emissions and reducing costs through lower fuel usage. A significant tool towards developing vehicles with lower drag is the wind tunnel. The automobile industry has made great improvements in fuel efficiency by using wind tunnels to determine the best designs to achieve lower drag. Those wind tunnels are not optimum for testing the larger, longer heavy trucks since the wind tunnels are smaller than needed. The estimated costs for a heavy truck wind tunnel based on automotive wind tunnel technology are quite high. A potential nozzle concept to reduce wind tunnel cost and several other new possible approaches to lower wind tunnel costs are presented.

This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheel and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.

This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.

HIGH output per cubic inch of piston displacement is desirable not alone for the purpose of being able to transport more payload faster, but more particularly for the invariably associated byproduct of lower specific fuel consumption, and especially at road-load requirements. The only way of accomplishing this purpose is through the use of higher compression ratios, and the limiting factors for this objective are fuel distribution and the operating temperatures of the component parts. A manifold is proposed which not only definitely improves distribution at both full and road loads, but has the inherent additional advantage of reducing the formation of condensate, thus still further facilitating a reduction in road-load specific fuel consumption. Hydraulic valve lifters, obviation of mechanical and thermal distortion, and controlled water flow are the essentials in improved cooling.

Find out why you should attend the 2025 Noise and Vibration Conference and Exhibition.

Find out why you should attend the 2023 Noise and Vibration Conference and Exhibition.

Bus drivers are daily exposed to whole-body vibrations (WBV) submitted to risks for develop health problems related to these conditions. Numerous studies focused to quantify and identify the risks that drivers are exposed have been developed in recent years. Many factors influence the transmission of vibration to the body. Road type may be an important factor in determining the WBV exposure a bus driver receives. In urban areas, common types of routes include several road surfaces like: smooth highway, older rough freeway, pavement, bumpy, speed humps, and others. The purpose of this study was to determine whether different kinds of road surfaces, found in urban routes, cause different WBV responses, and determine the influence for each road type in daily exposure to WBV according the standard ISO 2631-1 (1997).

Statistical measures of whole-body vibration from ambulation are shown to be higher than those from operation of earthmoving machinery and significantly higher than published guidelines for human exposure to whole-body vibration. The inconsistency of human response to low level vibration of technological origin as compared to human imperceptiveness to high level vibration from ambulation is discussed.