Search Results

A glossary of basic terms and definitions useful for working in reliability, maintainability, and sustainability (RMS). The terms used in most engineering technologies tend to be physical characteristics such as speed, rate of turn, and fuel consumption. While they may require very careful definition and control of the way in which they are measured, the terms themselves are not subject to different interpretations. Reliability, maintainability, and sustainability (RMS), however, use terms that are defined in a variety of ways with multiple interpretations. The variety of definitions given to a single term creates problems when trying to compare the performance of one system to another. To eliminate the confusion, a literature search that listed current and past RMS terms and definitions was conducted. The literature search included input from the U.S. military, UK military, NATO, SAE, IEEE, NASA, ISO, university research, and other publications.

This recommended practice has been developed for use in any EEE system used in the AADHP industries. RPA is especially important to AADHP systems, which are often safety critical applications that must operate for long times in rugged environments. These EEE systems often use EEE components that were originally designed and produced for more benign consumer applications. Although the focus of this recommended practice is on AADHP applications, the process described herein is not limited to AADHP and may be used for EEE systems and components in any industry.

This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence.

This document has been declared "CANCELLED" as of July 2008 and has been superseded by PRI AC7102/1. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7102/1. Cancelled specifications are available from SAE.

This document has been declared "CANCELLED" as of April 2005 and has been superseded by PRI AC7108/2. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7108/2. Cancelled specifications are available from SAE.

This Aerospace Standard (AS) is to be used as a supplement to SAE AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking NADCAP Coatings accreditation who are engaged in thermal spray.

This Aerospace Standard (AS) is to be used as a supplement to SAE AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking NADCAP Coatings accreditation who are engaged in stripping of coated material.

This Aerospace Standard (AS) is to be used to supplement AS7108. In addition to the requirements contained in AS7108, the requirements contained herein shall apply to suppliers seeking NADCAP accreditation for painting and dry film coatings.

This Aerospace Standard (AS) establishes the requirements for suppliers of Chemical Processing Services to be accredited by the National Aerospace and Defense Contractors Accreditation Program (NADCAP). NADCAP accreditation is granted in accordance with SAE AS7003 after demonstrating compliance with the requirements herein. These requirements may be supplemented by additional requirements specified by NADCAP Chemical Processes Task Group. Using the audit checklist (AC7108) will ensure that accredited Chemical Process suppliers meet all of the requirements in this standard and all applicable supplementary standards.

This SAE Standard covers engine military oils suitable for lubrication of reciprocating internal combustion engines of both spark-ignition and compression-ignition types, and for power transmission fluid applications in combat/tactical service equipment (see 7.1). This document is equivalent to MIL-PRF-2104G when all requirements are met.

This SAE Standard provides ordering information for any SAE 20R5 hose type (such as “EC, HT, LT” or combination thereof.) This is a wire-reinforced hose for coolant circulating systems of automotive type engines. This hose consists of a convoluted section with plain ends. The hose shall contain a wire helix or helices in the convoluted section. It is a supplement for Government use but may be used by others.

The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid-type, automotive gear units, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).

The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid-type, automotive gear units, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).

The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid-type, automotive gear units, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).

This SAE Aerospace Standard (AS) defines the requirements for air cycle air conditioning systems used on military air vehicles for cooling, heating, ventilation, and moisture and contamination control. General recommendations for an air conditioning system, which may include an air cycle system as a cooling source, are included in MIL-E-18927E and JSSG-2009. Air cycle air conditioning systems include those components which condition high temperature and high pressure air for delivery to occupied and equipment compartments and to electrical and electronic equipment. This document is applicable to open and closed loop air cycle systems. Definitions are contained in Section 5 of this document.

This SAE Aerospace Information Report (AIR) lists military and industry specifications, standards, recommended practices, and information reports applicable to aerospace hydraulic and pneumatic systems and components.

The primary purpose of a Propellant Transfer Unit (PTU) is to temperature-condition and weigh a specific amount of propellant, and transfer if to a vehicle propellant tank. A secondary purpose of a PTU may be to drain propellant from the vehicle tank and return it to the transfer unit when required. The transfer unit may also be used for flushing the vehicle fill lines and transfer unit with appropriate flushing fluids, followed with nitrogen for the purpose of drying the lines and weigh tank. The transfer unit may include provisions for helium purging of the propellant transfer tank and lines, ad supplying a blanket of helium pressure to the transfer tank. Each PTU consists of a piping system with appropriate propellant and pneumatic valves, regulators, relief valves, filters and a propellant pump. Various components such as a scrubber, bubbler, propellant cooler (heat exchanger), propellant weigh tank, weigh scale and a chiller may make up the balance of the assembly.

AIR5317 establishes the foundation for developing a successful APU health management capability for any commercial or military operator, flying fixed wing aircraft or rotorcraft. This AIR provides guidance for demonstrating business value through improved dispatch reliability, fewer service interruptions, and lower maintenance costs and for satisfying Extended Operations (ETOPS) availability and compliance requirements.