Search Results

Cooled exhaust gas recirculation (EGR) is widely used in diesel engines to control engine-out NOx (oxides of nitrogen) emissions. A portion of the exhaust gases is re-circulated into the intake manifold of the engine after cooling it through a heat exchanger. EGR cooler heat exchangers, however, tend to lose efficiency and have increased pressure drop as deposit forms on the heat exchanger surface due to transport of soot particles and condensing species to the cooler walls. In this study, condensation of water vapor and hydrocarbons at the exit of the EGR cooler was visualized using a fiberscope coupled to a camera equipped with a complementary metal oxide semiconductor (CMOS) color sensor. A multi-cylinder diesel engine was used to produce a range of engine-out hydrocarbon concentrations. Both surface and bulk gas condensation were observed with the visualization setup over a range of EGR cooler coolant temperatures.

Among all the reciprocating internal combustion engines, gasoline two-strokes can reach the highest specific power, making this technology a natural enabler of downsizing and/or down-speeding. In addition, multi-cylinder 2-stroke engines may be an ideal match for electrical superchargers, providing very efficient power units. The paper explores through CFD-1d simulations and empirical hypotheses the potential of a 3-cylinder, 1.0 liter, GDI 2-stroke turbocharged engine featuring a patented rotary valve for the optimization of the scavenging process, the latter being of the loop type (piston-controlled ports). The lubrication system is the same of a 4-stroke engine (no crankcase pumps). The supercharging system is made up of a turbocharger and an electric compressor, serially connected. The power of the electric compressor is limited to 2 kW, in order to comply with standard automotive 12 V electric systems.

This work reports a CFD study on a 2-stroke (2-S) opposed piston high speed direct injection (HSDI) Diesel engine. The engine main features (bore, stroke, port timings, et cetera) are defined in a previous stage of the project, while the current analysis is focused on the assembly made up of scavenge ports, manifold and cylinder. The first step of the study consists in the construction of a parametric mesh on a simplified geometry. Two geometric parameters and three different operating conditions are considered. A CFD-3D simulation by using a customized version of the KIVA-4 code is performed on a set of 243 different cases, sweeping all the most interesting combinations of geometric parameters and operating conditions. The post-processing of this huge amount of data allow us to define the most effective geometric configuration, named baseline.

A Machine Learning (ML) approach is presented to correlate in-cylinder images of early flame kernel development within a spark-ignited (SI) gasoline engine to early-, mid-, and late-stage flame propagation. The objective of this study was to train machine learning models to analyze the relevance of flame surface features on subsequent burn rates. Ultimately, an approach of this nature can be generalized to flame images from a variety of sources. The prediction of combustion phasing was formulated as a regression problem to train predictive models to supplement observations of early flame kernel growth. High-speed images were captured from an optically accessible SI engine for 357 cycles under pre-mixed operation. A subset of these images was used to train three models: a linear regression model, a deep Convolutional Neural Network (CNN) based on the InceptionV3 architecture and a CNN built with assisted learning on the VGG19 architecture.

The new Stage 5 European regulation for Non Road Mobile Machinery has lowered the limits on pollutant emissions for all the categories of internal combustion engines. An interesting alternative to the implementation of sophisticated after-treatment systems is to downsize the engine, and provide the extra power for peak demands with an electric motor, installed in place of the flywheel. The paper explores the potential of this concept, applied to an industrial engine, manufactured by Kohler, and delivering a maximum power of 56 kW@2600 rpm. The study is supported by a comprehensive experimental characterization of the internal combustion engine and of the electric components. A representative duty cycle is also defined, on the basis of a set of measures, taken in real operating conditions. The analysis of this reference cycle is performed by using a GT-Suite model, comparing different power split strategies.

Interest in 2-stroke engines has been recently renewed by several prototypes, developed for the automotive and/or the aircraft field. Loop scavenging, with piston controlled ports is particularly attractive, but the configurations successfully developed in the past for motorbike racing (in particular, the 125cc unit displacement, crankcase pump engines), are not suitable for automotive applications. Therefore, new criteria are necessary to address the scavenging system design of the new generation of 2-stroke automobile/aircraft engines. The paper reviews the transfer ports optimization of a loop scavenged 2-stroke cylinder, whose main parameters were defined in a previous study. The optimization has been carried by means of a parametric grid, considering 3 parameters (2 tilt angles, and the focus distance), and 3 different engine speeds (2000-3000-4000 rpm, assuming a Diesel engine). A set of scavenging CFD-3d simulations have been performed by using a customized version of KIVA-3V.

Thermal cabin comfort is the largest consumer of battery energy second only to propulsion in Battery Electric Vehicles (BEV’s). Accurate prediction of thermal comfort in the vehicle cabin with fast turnaround times will allow engineers to study the impact of various thermal comfort technologies and develop energy efficient Heating, Ventilation and Air Conditioning (HVAC) systems. In this study a novel data-driven model based on physics-guided Sparse Identification of Nonlinear Dynamics (SINDy) method was developed to predict Equivalent Homogeneous Temperature (EHT), Mean Radiant Temperature (MRT) and cabin air temperature under transient conditions and drive cycles. EHT is a recognized measure of the total heat loss from the human body that can be used to characterize highly non-uniform thermal environments such as a vehicle cabin. The SINDy model was trained on drive cycle data from Climatic Wind Tunnel (CWT) for a representative Battery Electric Vehicle.

Oxygen enriched air (EA) is a well known industrial mixture in which the content of oxygen is higher respect the atmospheric one, in the range 22-35%. Oxygen EA can be obtained by desorption from water, taking advantage of the higher oxygen solubility in water compared to the nitrogen one, since the Henry constants of this two gases are different. The production of EA by this new approach was already studied by experimental runs and theoretical considerations. New results using salt water are reported. EA promoted combustion is considered as one of the most interesting technologies to improve the performance in diesel engines and to simultaneously control and reduce pollution. This paper explores, by means of 3-dimensional computational fluid dynamics simulations, the effects of EA on the performance and exhaust emissions of a high-speed direct-injection diesel engine.

A new electronic sensor has been developed to measure the time-resolved concentration of carbonaceous particulate matter (PM) emitted in engine exhaust. The sensor is approximately the size of a standard automotive spark-plug or lambda sensor and can be mounted directly in the engine exhaust. It consists of a pair of closely spaced electrically isolated electrodes that protrude into the exhaust flow. One electrode is given a voltage bias of 1000 V while the other is the signal electrode. The sensor is capable of providing cycle-resolved feedback on the carbonaceous PM concentration in the exhaust to the engine control unit (ECU), thereby enabling real-time control of engine operating parameters to lower PM emissions. This paper reports the results of an experimental study of various parameters that affect the performance of the electronic sensor.

The motor generator unit installed on the turbocharger shaft (MGU-H) provides a fundamental contribution to the amazing performances and efficiency of the last Formula 1 power units. The excess of exhaust gas energy - normally dumped through the waste-gate - can be converted into electric energy and used to push the car, by means of a second motor generator unit installed on the engine crankshaft (MGU-K). The goal of this paper is to assess pros and cons of the MGU-H technology when applied to a family of engines of different displacement, installed on a typical passenger car. The influence of engine size and cylinders layout is investigated, under the same set of hypotheses, considering both transient and steady engine operations. The baseline engine is a commercial 2.0 L, SI, 4-cylinder in-line, rated at 200 HP at 4500-5000 rpm.

The basic requirements for range extender engines are low cost, compact dimensions, high specific power, good efficiency, low pollutant emission levels, excellent NVH behavior. For a power rate lower than 30 kW, it is very difficult to find an off-the-shelf engine meeting all the requirements listed above, so that a new generation of dedicated engines is under development. Following a preliminary theoretical work presented in 2012 [1], the current paper reviews the design process and the first experimental tests carried out on a novel 2-stroke GDI single-cylinder engine, rated at 30 kW at 4500 rpm, featuring a patented induction valve and a piston pump for scavenging. A prototype has been designed with the support of CFD simulations, then built and tested at the BRC laboratories, in Cherasco (Italy).

Sector mesh modeling is the dominant computational approach for combustion system design optimization. The aim of this work is to quantify the errors descending from the sector mesh approach through three geometric modeling approaches to an optical diesel engine. A full engine geometry mesh is created, including valves and intake and exhaust ports and runners, and a full-cycle flow simulation is performed until fired TDC. Next, an axisymmetric sector cylinder mesh is initialized with homogeneous bulk in-cylinder initial conditions initialized from the full-cycle simulation. Finally, a 360-degree azimuthal mesh of the cylinder is initialized with flow and thermodynamics fields at IVC mapped from the full engine geometry using a conservative interpolation approach. A study of the in-cylinder flow features until TDC showed that the geometric features on the cylinder head (valve tilt and protrusion into the combustion chamber, valve recesses) have a large impact on flow complexity.

The paper presents a preliminary study on a virtual 2-stroke 3-cylinder 0.9 L DI SI supercharged engine running on Hydrogen (H2), able to meet both high performance targets and ultra-low emissions limits (NOx<20 ppm). Combustion is similar to a conventional 4-stroke H2 DI engine, while the design of the cylinder and the actuation law of both intake and exhaust valves are specifically optimized for the 2-stroke cycle. In comparison to a more conventional 2-stroke loop scavenged engine, with piston-controlled ports, the use of poppet valves enables a more flexible control of the gas exchange process and to maintain the same design of a 4-stroke engine for pistons, cylinders block, crankcase and lubrication system. On the other hand, it is more difficult to avoid the short-circuit of the fresh charge, while permeability of the valves becomes quite critical at high engine speed.

Effects of six different fuels on low temperature premixed compression ignition (PCI) combustion were experimentally investigated in this paper with a light-duty HSDI engine. The PCI combustion concept reduces NOx and smoke emissions simultaneously by low temperature and premixed combustion, respectively. To achieve low temperature and premixed combustion, the ignition delay is prolonged and the injection duration is shortened. Six fuels were chosen to examine the influence of cetane number (CN) and other fuel properties on low temperature PCI combustion. The fuel selection also included a pure Gas- to-Liquid (GTL) fuel and a blend of base diesel and 20% soy based biodiesel (B20). Fuel effects were studied over a matrix of seven part load points in the low temperature combustion mode. The seven part load points were specified by engine speed (RPM) and brake mean effective pressure (BMEP).

One of the main challenges related to the use of Hydrogen in Internal Combustion Engines is the trade-off between NOx emissions and brake power output: on the one hand, a lean premixed charge (Lambda ≈2.5) is generally able to provide a regular and efficient combustion, yielding near-zero NOx emissions; on the other hand, the power density tends to be very poor, due to the huge amount of air required by the thermodynamic process. As a further penalization, the injection of a gaseous fuel during the intake process has a negative impact on volumetric efficiency. Supercharging can be a solution for addressing the problem, but at the cost of an increase of complexity, cost and overall dimensions. An alternative path is represented by the 2-stroke cycle, and, in particular, by the opposed piston (OP) design. Most of the existing OP engines are compression ignited, but Spark ignition and direct fuel injection can be implemented without relevant modifications to the layout of cylinders.

In light- and medium-duty diesel engines, piston bowl shape influences thermal efficiency, either due to changes in wall heat loss or to changes in the heat release rate. The relative contributions of these two factors are not clearly described in the literature. In this work, two production piston bowls are adapted for use in a single cylinder research engine: a conventional, re-entrant piston, and a stepped-lip piston. An injection timing sweep is performed at constant load with each piston, and heat release analyses provide information about thermal efficiency, wall heat loss, and the degree of constant volume combustion. Zero-dimensional thermodynamic simulations provide further insight and support for the experimental results. The effect of bowl geometry on wall heat loss depends on injection timing, but changes in wall heat loss cannot explain changes in efficiency.

A pilot-main injection strategy is investigated for a part-load operating point in a single cylinder optical Diesel engine. As the energizing dwell between the pilot and main injections decreases below 200 μs, combustion noise reaches a minimum and a reduction of 3 dB is possible. This decrease in combustion noise is achieved without increased pollutant emissions. Injection schedules employed in the engine are analyzed with an injection analyzer to provide injection rates for each dwell tested. Two distinct injection events are observed even at the shortest dwell tested; rate shaping of the main injection occurs as the dwell is adjusted. High-speed elastic scattering imaging of liquid fuel is performed in the engine to examine initial liquid penetration rates.

In order to investigate the effects of split injection on emission formation and engine performance, experiments were carried out using a heavy duty single cylinder diesel engine. Split injections with varied dwell time and start of injection were investigated and compared with single injection cases. In order to isolate the effect of the selected parameters, other variables were kept constant. In this investigation no EGR was used. The engine was equipped with a common rail injection system with a piezo-electric injector. To interpret the observed phenomena, engine CFD simulations using the KIVA-3V code were also made. The results show that reductions in NOx emissions and brake specific fuel consumption were achieved for short dwell times whereas they both were increased when the dwell time was prolonged. No EGR was used so the soot levels were already very low in the cases of single injections.

Biodiesel from Algae appears as an almost ideal solution to address the problem of decreasing availability of conventional fossil fuels, as well as to reduce the impact in terms of CO2 of internal combustion engines. In comparison to other biodiesels, algae do not compete for the land use with food cultures, and they have an excellent oil yield. Despite the significant amount of technical reports about the production process of algal biodiesel, detailed information about the application to current production engines is almost completely missing. The present paper describes the experimental campaign carried out on a current production 4-cylinder, 4-stroke naturally aspirated Diesel engine, running on standard Diesel oil and on a blend made up of 20% of oil manufactured by transesterification of Microalgae (B20). Performance and emission parameters have been measured over the whole engine operating range.

Regulated emissions and fuel consumption are the main constraints affecting internal combustion engine (ICE) design. Over the years, many techniques have been used with the aim of meeting these limitations. In particular, exhaust gas recirculation (EGR) has proved to be an invaluable solution to reduce NOx emissions in Diesel engines, becoming a widely used technique in production engines. However, its application has a direct effect on fuel consumption due to both the changes in the in-cylinder processes, affecting indicated efficiency, and also on the air management. An analysis, based on the engine Global Energy Balance, is presented to thoroughly assess the behavior of a HSDI Diesel engine under variable EGR conditions at different operating points. The tests have been carried out keeping constant the conditions at the IVC and the combustion centering.