Refine Your Search

Date

Date

Test equipment and instrumentation Cartography Optics Circuit Protection and Switch Device Committee Data management

Search Results

Viewing 1 to 20 of 27
12Next >Last >>
Sort by title
Standard

WARNING LAMP ALTERNATING FLASHERS
1994-09-01
HISTORICAL
J1054_199409
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6,12, and 24 V warning lamp alternating flashers.
Standard

WARNING LAMP ALTERNATING FLASHERS
1989-10-01
HISTORICAL
J1054_198910
This document defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V warning lamp alternating flashers.
Standard

VEHICULAR HAZARD WARNING SIGNAL FLASHER
1987-06-01
HISTORICAL
J945_198706
This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt hazard warning signal flashers.
Standard

VEHICULAR HAZARD WARNING FLASHERS
1993-06-01
HISTORICAL
J945_199306
This SAE Standard defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V hazard warning flashers.
Standard

TURN SIGNAL FLASHERS
1968-04-01
HISTORICAL
J590C_196804
Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal system as stated by the manufacturer.
Standard

TURN SIGNAL FLASHERS
1986-07-01
HISTORICAL
J590_198607
This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt turn signal flashers.
Standard

SIX- AND TWELVE-VOLT CIGAR LIGHTER RECEPTACLES
1990-03-16
HISTORICAL
J563_199003
This SAE Standard covers the basic cigar lighter receptacle, which may optionally incorporate overload protective devices. Figure 1 and Table 1 show the cigar lighter receptacle and its pertinent dimensions. Lighter plugs shall be permanently marked either "6 volt" or "12 volt". Manufacturers of accessory plugs to energize devices such as trouble lamps and razors are cautioned to conform to the provisions given in this document. Live contact of any accessory plug shall be made with the center stud; the contacting member must not be less than 3.56 mm in diameter and have a minimum spherical radius of 2.54 mm at the contacting end. To prevent damage, the body of an accessory plug back of the contact end should be large enough to serve as a centering guide when it is inserted into the receptacle. The contact end of any accessory plug should have sufficient taper so as not to interfere with the receptacle bimetal fingers.
Standard

MECHANICAL STOP LAMP SWITCH
1988-06-01
CURRENT
J249_198806
The mechanical stop lamp switch is an operator activated mechanical device intended primarily to control the functioning of the stop lamp and high mounted stop lamp circuits. Secondarily, the device may control the functioning of various accessories, such as disengaging cruise control, with operator actuation of brake pedal.
Standard

HEADLAMP BEAM SWITCHING
1990-03-16
CURRENT
J564_199003
This SAE Standard defines the test conditions, procedures and performance specification for 6, 12, and 24 V manually actuated headlamp beam control switches.
Standard

HAZARD WARNING SIGNAL SWITCH
1988-10-01
CURRENT
J910_198810
This standard defines the test conditions, procedures and performance specifications for 6, 12 and 24-V manually actuated hazard warning signal switch.
Standard

FLASHERS
1996-08-01
CURRENT
J1690_199608
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V turn signal, hazard warning, warning lamp alternating, and combination flashers.
Standard

ELECTRIC WINDSHIELD WIPER SWITCH
1977-10-01
CURRENT
J112_197710
This SAE Recommended Practice covers temperature test, endurance test setup, and endurance requirements for an electric windshield wiper switch. It also covers the combination windshield wiper and washer switch.
Standard

DOOR COURTESY SWITCH
1991-06-01
HISTORICAL
J2108_199106
This SAE Recommended Practice defines the test conditions, procedures, and performance requirements for 6, 12, and 24 V Door Courtesy Switches which are intended for use in motor vehicles.
12Next >Last >>
X