Refine Your Search

Date

Date

Topic

Topic

Data management Circuit Protection and Switch Device Committee Cartography Optics Manufacturing

Search Results

Viewing 1 to 20 of 20
1
Sort by title
Standard

WARNING LAMP ALTERNATING FLASHERS
1994-09-01
HISTORICAL
J1054_199409
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6,12, and 24 V warning lamp alternating flashers.
Standard

WARNING LAMP ALTERNATING FLASHERS
1989-10-01
HISTORICAL
J1054_198910
This document defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V warning lamp alternating flashers.
Standard

WARNING LAMP ALTERNATING FLASHERS
1977-01-01
HISTORICAL
J1054_197701
Flashers referred to in this SAE recommended engineering design practice are for nominal 12 V circuits and are required to operate the maximum design load per output terminal as stated by the flasher manufacturer. This design practice is intended for use in conjunction with a supplementary Service Performance Standard for Warning Lamp Flashers (under development).
Standard

WARNING LAMP ALTERNATING FLASHERS
1973-09-01
HISTORICAL
J1054_197309
Flashers referred to in this SAE recommended engineering design practice are for nominal 12 V circuits and are required to operate the maximum design load per output terminal as stated by the flasher manufacturer. This design practice is intended for use in conjunction with a supplementary Service Performance Standard for Warning Lamp Flashers (under development).
Standard

TURN SIGNAL FLASHERS
1968-04-01
HISTORICAL
J590C_196804
Flashers referred to in this SAE Standard are for nominal 12 or 6 dc circuits and are intended to operate at the design loads for the turn signal system as stated by the manufacturer.
Standard

TURN SIGNAL FLASHERS
1986-07-01
HISTORICAL
J590_198607
This recommended practice defines the test conditions, procedures and minimum design requirements for nominal 6, 12 and 24 volt turn signal flashers.
Standard

Standard for 12 Volt Cigarette Lighters, Power Outlets, and Accessory Plugs
2009-02-05
CURRENT
J563_200902
This standard is intended to cover cigar or cigarette lighters as well as power outlets based on the form and dimensions of the cigar lighter, and accessory plugs for use in these devices. Components covered herein are designed to work in nominal 12 VDC systems. This standard is a full performance specification. It includes dimensional and operational parameters as well as performance characteristics which must be met when submitting a cigar lighter assembly, power outlet assembly, or plug for production approval. This standard constitutes an acceptance specification for these devices. This standard covers the operational, reliability, durability, acceptance, and testing requirements for a cigar lighter (also referred to as just “lighter”) for installation in the passenger compartment of production vehicles.
Standard

SIX- AND TWELVE-VOLT CIGAR LIGHTER RECEPTACLES
1990-03-16
HISTORICAL
J563_199003
This SAE Standard covers the basic cigar lighter receptacle, which may optionally incorporate overload protective devices. Figure 1 and Table 1 show the cigar lighter receptacle and its pertinent dimensions. Lighter plugs shall be permanently marked either "6 volt" or "12 volt". Manufacturers of accessory plugs to energize devices such as trouble lamps and razors are cautioned to conform to the provisions given in this document. Live contact of any accessory plug shall be made with the center stud; the contacting member must not be less than 3.56 mm in diameter and have a minimum spherical radius of 2.54 mm at the contacting end. To prevent damage, the body of an accessory plug back of the contact end should be large enough to serve as a centering guide when it is inserted into the receptacle. The contact end of any accessory plug should have sufficient taper so as not to interfere with the receptacle bimetal fingers.
Standard

HAZARD WARNING SIGNAL SWITCH
1988-10-01
CURRENT
J910_198810
This standard defines the test conditions, procedures and performance specifications for 6, 12 and 24-V manually actuated hazard warning signal switch.
Standard

FLASHERS
1996-08-01
CURRENT
J1690_199608
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V turn signal, hazard warning, warning lamp alternating, and combination flashers.
Standard

ELECTRIC FUSES (CARTRIDGE TYPE)
1987-08-01
CURRENT
J554_198708
The fuses shown are for use in motor vehicles, boats, and trailers to protect electrical wiring and equipment. This standard is for the construction shown and is not intended to restrict the design and use of other configurations and materials capable of meeting the vehicle requirements.
Standard

DOOR COURTESY SWITCH
1991-06-01
HISTORICAL
J2108_199106
This SAE Recommended Practice defines the test conditions, procedures, and performance requirements for 6, 12, and 24 V Door Courtesy Switches which are intended for use in motor vehicles.
Standard

DOOR COURTESY SWITCH
1991-12-01
CURRENT
J2108_199112
This SAE Recommended Practice defines the test conditions, procedures, and performance requirements for 6, 12, and 24 V Door Courtesy Switches which are intended for use in motor vehicles.
Standard

BACKUP LAMP SWITCH
1990-03-16
CURRENT
J1076_199003
This standard defines the test conditions, procedures and performance specification for 6, 12, and 24 V backup lamp switches which are intended for use in motor vehicles.
Standard

AUTOMOTIVE TURN SIGNAL FLASHERS
1965-10-01
HISTORICAL
J590B_196510
Flashers referred to in this SAE Standard are for nominal 12 or 6 v d-c circuits and are intended to operate at the design load for the turn signal system as stated by the manufacturer. EXAMPLE: two No. 1034 bulbs plus one No. 57 pilot bulb or three No. 1073 bulbs plus one No. 57 pilot bulb.
Standard

AUTOMOTIVE TURN SIGNAL FLASHERS
1965-07-01
HISTORICAL
J590B_196507
Flashers referred to in this SAE Standard are for nominal 12 or 6 v d-c circuits and are intended to operate at the design load for the turn signal system as stated by the manufacturer. EXAMPLE: two No. 1034 bulbs plus one No. 57 pilot bulb or three No. 1073 bulbs plus one No. 57 pilot bulb.
1
X