Search Results

Targeted fuel blending is a known method to improve the performance of an automotive engine. Two candidates for a biofuel blend are the linear C8H18O isomers 1-octanol and di-n-butyl ether (DNBE). Both fuels feature an increased amount of oxygen that reduces soot emissions. However, physical properties of both fuels differ significantly and thus, a different type of spray mixing and combustion is expected: The low reactivity of 1-octanol causes a long ignition delay enabling a better mixture homogenization, but also causes HC and CO emissions. DNBE in contrary is highly volatile, has a short ignition time and thus can act as an ignition booster for 1-octanol without losing positive effects concerning emissions. In this work a spray study is performed for blends of 1-octanol and DNBE. Measurements are conducted under diesel-like engine conditions with an 8-hole piezo injector. High-speed Schlieren and Mie scattering techniques are used for spray visualizations.

One of the fundamental topics in the design of new injection systems for Dl Diesel engines is to decrease the soot emissions. A promising approach to minimize soot production are injection nozzles having clustered holes. The basic idea of Cluster Configuration (CC) nozzles is to prevent a fuel rich area in the center of the flame where most of the soot is produced. For this purpose each hole of a conventional nozzle is replaced by two smaller holes, which are sized to yield the same flow rate. The basic strategy of the cluster nozzles is to provide a better primary break up, and therefore a better mixture formation, caused by the smaller nozzle holes, but a comparable penetration length of the vapor phase due to merging of the spray plumes.

A parametric study on the effects of critical injector design parameters of inwardly-opening pressure-swirl injectors was carried out using 3-D internal flow simulations. The pressure variation and the integrated momentum flux across the injector, as well as the flow distributions and turbulence structure at the nozzle exit were analyzed. The critical flow effects on the injector design identified are the swirler efficiency, discharge coefficient, and turbulence breakup effects on the spray structure. The study shows that as a unique class of injectors, pressure-swirl injectors is complicated in fluid mechanics and not sufficiently characterized or optimized. The swirler efficiency is characterized in terms of the trade-off relationship between the swirl-to-axial momentum-flux ratio and pressure drop across the swirler. The results show that swirl number is inversely proportional to discharge coefficient, and that hole diameter and swirler height is the most dominant parameters.

In present GDI engines, multiple injection strategies are often employed for engine cold start mixture formation. In the future, these strategies may also be used to control the combustion process, and to prevent misfiring or high emission levels. While the processes occurring during individual injections of GDI injectors have been investigated by a number of researchers, this paper concentrates on the interactions of multiple injection events. Even though multiple injection strategies are already applied in most GDI engines, the impact of the first injection event on the second injection event has not been analyzed in detail yet. Different optical measurement techniques are used in order to investigate the interaction of the two closely timed injection events, as well as the effect of dwell time and the in-cylinder conditions. The injector investigated is a GDI piezo injector with an outwardly opening needle.

An experimental study on the interaction of sprays from clustered orifices is presented. Droplet size and velocity information has been gained by means of Phase Doppler Anemometry for different nozzle configurations varying the diverging opening angle between clustered sprays from 0° to 15°. These nozzles were investigated under high-pressure (50 bar) and high-temperature (800 K) conditions in a pressure chamber and the results are compared to two standard nozzles with flow rates corresponding either to the flow rate of the cluster nozzle configuration or half of the flow rate of this configuration. Two injection pressures, 600 bar and 1100 bar, were used to investigate all nozzles. This investigation completes the characterization of sprays from the cluster nozzles presented in an earlier work. Findings obtained therein were used to choose the measurement procedure for the present investigation and also to determine the spray width in order to obtain the spray angle.

Since the amount of dissolved gas in fuels is an important quantity for the description of aeration in injection nozzles, this paper presents Bunsen absorption coefficients for different conventional and bio-hybrid fuels and their effect on nozzle flow phenomena. Bio-hybrid fuels can be produced both on the basis of biomass and with the help of regeneratively generated electrical energy. In contrast to previous work, the Bunsen coefficient was determined for a wide pressure range from approximately 10 MPa to 32.5 MPa. In fact, some of the fuels considered here were never before objects of investigation in terms of their solubility properties. In this work, large differences regarding the Bunsen absorption coefficient between a conventional fuel and a bio-hybrid fuel were observed. For determining the solubility of the fuels, a manometric-volumetric method was used.