Search Results

Particle image velocimetry measurements of the in-cylinder flow in an optically accessible single-cylinder research engine were taken to better understand the effects of intake pressure variations on the flow field. At a speed of 1500 rpm, the engine was run at six different intake pressure loads from 0.4 to 0.95 bar under motored operation. The average velocity fields show that the tumble center position is located closer to the piston and velocity magnitudes decrease with increasing pressure load. A closer investigation of the intake flow near the valves reveals sharp temporal gradients and differences in maximum and minimum velocity with varying intake pressure load which are attributed to intake pressure oscillations. Despite measures to eliminate acoustic oscillations in the intake system, high-frequency pressure oscillations are shown to be caused by the backflow of air from the exhaust to the intake pipe when the valves open, exciting acoustic modes in the fluid volume.

The engine fueled with methane/diesel is a promising and highly attractive operation mode due to its high performance-to-cost ratio and clean-burning qualities. However, the combustion process and chemical reactions in dual fuel combustion are highly complex, involving short transient pilot-fuel injection into the premixed gaseous fuel charge, autoignition, and combustion mode transition into premixed flame propagation. The motivation of the current investigation is to gain an insight into the combustion dynamics in dual fuel combustion engine based on chemical radicals and thermal radiation. The chemiluminescence (CL) and natural luminosity (NL) are expected to provide specific characteristics in combustion control and monitoring. To visualize the highly unsteady combustion process in terms of OH*, CH2O* radicals and natural luminous emissions, the band pass filters with 308 nm, 330 nm combined with an image doubler are employed to visualize the OH* and CH2O* CL simultaneously.

Non-evaporating diesel sprays have been simulated utilizing the ETAB and the WAVE atomization and breakup models and have been compared with experimental data. The experimental penetrations and widths were determined from back-lit spray images and the droplet sizes have been measured by means of a Malvern particle sizer. The model evaluation criteria include the spray penetration, the spray width and the local droplet size. The comparisons have been performed for variations of the injection pressure, the gas density and the fuel viscosity. The fuel nozzle exit velocities used in the simulations have been computed with a special code that considers the effect of in-nozzle cavitation. The simulations showed good overall agreement with experimental data. However, the capabilities of the models to predict the droplet size for different fuels could be improved.

The objective of this study was to build up an optical access into a large bore medium-speed research engine and carry out the first fuel spray Particle Image Velocimetry (PIV) measurements in the running large bore medium-speed engine in high pressure environment. The aim was also to measure spray penetration with same optical access and apparatus. The measurements were performed in a single-cylinder large bore medium-speed research engine, the Extreme Value Engine (EVE) with optical access into the combustion chamber. The authors are not aware of any other studies on optical spray measurements in large bore medium-speed diesel engines. Successful optical measurements of the fuel spray penetration and the velocity fields were carried out. This confirms that the exceptional component design and laser sheet alignment used in this study proved to be valid for optical fuel spray measurements in large-bore medium-speed diesel engines.

Hydrogen (H2), a potential carbon-neutral fuel, has attracted considerable attention in the automotive industry for transition toward zero-emission. Since the H2 jet dynamics play a significant role in the fuel/air mixing process of direct injection spark ignition (DISI) engines, the current study focuses on experimental and numerical investigation of a low-pressure H2 jet to assess its mixing behavior. In the experimental campaign, high-speed z-type schlieren imaging is applied in a constant volume chamber and H2 jet characteristics (penetration and cross-sectional area) are calculated by MATLAB and Python-based image post-processing. In addition, the Unsteady Reynolds-Averaged Navier-Stokes (URANS) approach is used in the commercial software Star-CCM+ for numerical simulations.

Ammonia (NH3), as a carbon-free fuel, has a higher optimization potential to power internal combustion engines (ICEs) compared to hydrogen due to its relatively high energy density (7.1MJ/L), with an established transportation network and high flexibility. However, the NH3 is still far underdeveloped as fuel for ICE application because of its completely different chemical and physical properties compared with hydrocarbon fuels. Among all uncertainties, the dynamics of the NH3 spray at engine conditions is one of the most important factors that should be clarified for optimizing the fuel-air mixing. To characterize the evolution and evaporation process of NH3 spray, a high-speed Z-type schlieren imaging technique is employed to estimate the spray characteristics under different injection pressure and air densities in a constant volume chamber.

This study is presenting a comparative spray study of modern large bore medium speed diesel engine common rail injectors. One subject of paper is to focus on nozzles with same nominal flow rate, but different machining. The other subject is penetration velocity measurements, which have a new approach when trying to understand the early phase of transient spray. A new method to use velocimetry for spray tip penetration measurements is here introduced. The length where spray penetration velocity is changed is found. This length seems to have clear connection to volume fraction of droplets at gas. These measurements also give a tool to divide the development of spray into acceleration region and deceleration region, which is one approach to spray penetration. The measurements were performed with backlight imaging in pressurized injection test rig at non-evaporative conditions. Gas density and injection pressure were matched to normal diesel engine operational conditions.

Fuel spray mixing has been analyzed numerically in a single-cylinder optical research engine with a flat piston top. In the study, a narrow spray angle has been used to align the sprays towards the piston top. Fuel spray mass flow rate has been simulated with 1-D code in order to have reliable boundary condition for the CFD simulations. Different start of fuel injections were tested as well as three charge air pressures and two initial mixture temperatures. Quantitative analysis was performed for the evaporation rates, mixture homogeneity at top dead center, and for the local air-fuel ratios. One of the observations of this study was that there exists an optimum start of fuel injection when the rate of spray evaporation and the mixture homogeneity are considered.

Dual fuel (DF) combustion technology as a feasible approach controlling engine-out emissions facilitates the concept of fuel flexibility in diesel engines. The abundance of natural gas (90-95% methane) and its relatively low-price and the clean-burning characteristic has attracted the interest of engine manufacturers. Moreover, with the low C/H ratio and very low soot producing tendency of methane combined with high engine efficiency makes it a viable primary fuel for diesel engines. However, the fundamental knowledge on in-cylinder combustion phenomena still remains limited and needs to be studied for further advances in the research on DF technology. The objective of this study is to investigate the ignition delay with the effect of, 1) methane equivalence ratio, 2) intake air temperature and 3) pilot ratio on the diesel-methane DF-combustion. Combustion phenomenon was visualized in a single cylinder heavy-duty diesel engine modified for DF operations with an optical access.

The distribution of spray droplet sizes plays a pivotal role in internal combustion engines, directly affecting fuel-air mixing, evaporation, and combustion. To gain a precise understanding of droplet size distribution in a two-dimensional space, non-intrusive optical diagnostics emerge as a highly effective method. In the current investigation, two-dimensional (2D) diesel spray droplet sizes mapping using a simultaneous combination of planar laser-induced fluorescence (PLIF) and Mie-scattering techniques is introduced. The assessment of droplet diameter relies on the interplay between fluorescent and scattered light intensities which correspond the light based on volumetric droplets and surface area of the droplets. This calculation is made possible through the LIF/Mie technique. However, traditional LIF/Mie methods are plagued by inaccuracies arising from multiple light scattering.