Search Results

The common realization of the necessity to reduce the use of mineral sources is promoting the use of alternative fuels. Big efforts are being made to replace petroleum derivatives in the internal combustion engines (ICEs). For this purpose it is mandatory to evaluate the behavior of non-conventional fuels in the ICEs. The optical diagnostics have proven to be a powerful tool to analyze the processes that take place inside the engine. In particular, 2d imaging in the infrared range can reveal new details about the effect of the fuel properties since this technique is still not very common. In this work, a comparison between commercial diesel fuel and two non-conventional fuels has been made in an optically accessible diesel engine. The non-conventional fuels are: the first generation biofuel Rapeseed Methyl Ester (RME) and an experimental blend of diesel and a fuel with high glycerol content (HG).

In this work, optical diagnostics were applied in a transparent DI diesel engine equipped with the head of Euro5 commercial engine and the last generation CR injection system. In order to realize the PCCI combustion the injection of neat bio-ethanol was performed in the intake manifold and European commercial diesel fuel was injected into the cylinder. Different amounts of bio-ethanol were injected in order to create PCCI combustion with high levels of pre-combustion mixing, and to ensure low equivalence ratio and low flame temperatures too. UV-Visible imaging and spectroscopic measurements were performed in the engine in order to investigate the autoignition of the charge and the combustion process, respectively. In particular, the detection of the species involved in the combustion, like OH, HCO, and CH, was performed. The relevance of the radicals and species on PCCI were evaluated and compared with the data from thermodynamic analysis.

Premixed charge compression ignition (PCCI) has been shown to be a promising strategy to simultaneously reduce emissions while realizing improved fuel economy. PCCI combustion uses high levels of pre-combustion mixing to lower both NOx and soot emissions by ensuring low equivalence ratio and low flame temperatures. The high level of pre-combustion mixing results in a primarily kinetics controlled combustion process. In this work, optical diagnostics have been applied in a transparent DI diesel engine equipped with the head of Euro5 commercial engine and the last generation CR injection system. In order to realize the PCCI combustion the injection of neat ethanol has been performed in the intake manifold. The engine run in continuous way at 1500 rpm engine speed and commercial diesel fuel has been injected into the cylinder. The PCCI combustion has been analyzed by means of UV- Visible digital imaging and the mixing process, the autoignition of the charge have been investigated.

The aim of this study is to investigate how the fouling that injectors undergo after several operating hours on a vehicle can affect the injection and combustion phases. The impact of the injector fouling on the pollutant formation has been also investigated. Moreover, the effects of the injector cleaning by deposits through the top quality diesel fuel commercialized by eni that is FAME free and contains multi performance additives have been investigated. The experimentation has been carried out on transparent compression ignition engine. It is a single cylinder equipped with a Euro 5 multi-cylinder head and a second-generation common rail injection system. Three indirect-acting piezoelectric injectors have been tested. The first one has been fouled with European commercial diesel fuel through the CEC DW10 injector-coking test. The second one has been fouled in the same way and, then, it has been cleaned with eni top quality diesel fuel. This fuel has fed the third injector too.

The present paper describes the results of a cooperative research project between GM Powertrain Europe and Istituto Motori - CNR aimed at studying the impact of both fresh and highly oxidized RME at two levels of blending on spray formation and combustion in modern automotive diesel engines. The tests were performed on an optical single-cylinder engine sharing combustion system configuration with the 2.0L Euro5 GM diesel engine for passenger car application. Two blends (B50 and B100) blending were tested for both fresh and aged RME and compared with commercial diesel fuel in two different operating points typical of NEDC (1500rpm/2bar BMEP and 2000rpm/5bar BMEP). The experimental activity was devoted to an in-depth investigation of the spray density, breakup and penetration, mixture formation, combustion and soot formation, by means of optical techniques.

This paper deals with the combustion behavior and exhaust emissions of a small compression ignition engine modified to operate in diesel/methane dual fuel mode. The engine is a three-cylinder, 1028 cm3 of displacement, equipped with a common rail injection system. The engine is provided with the production diesel oxidation catalyst. Intake manifold was modified in order to set up a gas injector managed by an external control unit. Experiments were carried out at different engine speeds and loads. For each engine operating condition, the majority of the total load was supplied by methane while a small percentage of the load was realized using diesel fuel; the latter was necessary to ignite the premixed charge of gaseous fuel. Thermodynamical analysis of the combustion phase was performed by in-cylinder pressure signal. Gas emissions and particulate matter were measured at the exhaust by commercial instruments.

This study was conducted to determine the effects of the fouling process on the piezoelectric injectors in a transparent common-rail diesel engine. Piezoelectric injectors are characterized by a ceramic actuator that can dilate or retract when it receives a pulse of current. The piezo element controls a valve, which creates an imbalance in the pressure that is exerted at each end of the needle, causing the needle rising or closing. Two same model injectors were tested; one was new and the other one was fouled on a vehicle. The aim of the experimental investigation was to evaluate the performance of a new and a fouled piezoelectric injector in terms of injection and flame evolution. It was evaluated how the nozzle carbon deposits affect the injection quantity and combustion. The experimental apparatus was a single-cylinder research engine equipped with a Euro 5 multi-cylinder head. A second-generation common rail injection system and 6-hole piezoelectric injectors were used too.

In order to reduce fuel consumption and polluting emissions from engines, alternative fuels such as hydrogen could play an important role towards carbon neutrality. Moreover, dual-fuel (DF) technology has the potential to offer significant improvements in carbon dioxide emissions for transportation and energy sectors. The dual fuel concept (natural gas/diesel or hydrogen/diesel) represents a possible solution to reduce emissions from diesel engines by using low-carbon or carbon-free gaseous fuels as an alternative fuel. Moreover, DF combustion is a possible retrofit solution to current diesel engines by installing a PFI injector in the intake manifold while diesel is injected directly into the cylinder to ignite the premixed mixture. In the present study, dual fuel operation has been investigated in a single cylinder research engine.

The transport of goods and people by sea, today, must meet the need to reduce the consumption of fuel oil. In addition, it has to ensure operational reliability and vessel availability, to reduce maintenance costs and comply with emission legislation. To this end, it is necessary to apply a marine engine combustion control system already widely used in engines for land transport. This will allow the ship's engines to operate reliably and in compliance with the best performance for which it was designed. The combustion control could also ensure a more balanced operation of the cylinders and reduce the torsional vibrations of the entire engine, as well as the management of the engine according to the adopted fuel: diesel, dual fuel, methanol, ammonia. Generally, the control of combustion in engines is carried out through the use of pressure sensors that face directly into the combustion chamber.

Blends of propane-diesel fuel can be used in direct injection diesel engines to improve the air-fuel mixing and the premixed combustion phase, and to reduce pollutant emissions. The potential benefits of usinf propane in diesel engines are both environmental and economic; furthermore, its use does not require changes to the compression ratio of conventional diesel engines. The present paper describes an experimental investigation of the injection process for different liquid preformed blends of propane-diesel fuel in an optically accessible Common Rail diesel engine. Slight modifications of the injection system were required in order to operate with a blend of propane-diesel fuel. Pure diesel fuel and two propane-diesel mixtures at different mass ratios were tested (20% and 40% in mass of propane named P20 and P40). First, injection in air at ambient temperature and atmospheric pressure were performed to verify the functionality of the modified Common Rail injection system.

Compression ignition engines are widely used for transport and energy generation due to their high efficiency and low fuel consumption. To minimize the environmental impact of this technology, the pollutant emissions levels at the exhaust are strictly regulated. To reduce the after-treatment needs, alternative strategies as the low temperature combustion (LTC) concepts are being investigated recently. The reactivity controlled compression ignition (RCCI) uses two fuels (direct- and port- injected) with different reactivity to control the in-cylinder mixture reactivity by adjusting the proportion of both fuels. In spite of the proportion of the port-injected fuel is typically higher than the direct-injected one, the characteristics of the latter play a main role on the combustion process. Use of gasoline for direct injection is attractive to retard the start of combustion and to improve the air-fuel mixing process.

Spectroscopic measurement and high speed visualization were used in single cylinder, four-stroke DI diesel engine, optically accessible. It was equipped with a four valves head and fully flexible electronic controlled ‘Common Rail’ injection system. The effect of pilot and main injection on combustion process was evaluated. Mixing formation, autoignition and soot formation process were analyzed by broadband ultraviolet-visible flame emission spectroscopy and high-speed digital imaging. The autoignition phase occurred near the tip of the jet and was characterized by strong presence of OH radicals for both investigated conditions The presence of C2 and OH radicals strongly characterized CR diesel combustion process during soot formation and evolution. In particular, high presence of OH concentration for the whole process from the autoignition to the soot formation and successive phases contributes to lower soot levels.

In the present paper, infrared (IR) measurements were performed in order to study the development of injection and combustion in a transparent Euro 5 diesel engine operating in premixed mode. An elongated single-cylinder engine equipped with the multi-cylinder head of commercial passenger car and with common rail (CR) injection system, respectively, was used. A sapphire window was set in the bottom of the combustion chamber, and a sapphire ring was placed between the head and the top of the cylinder line. Measurements were carried out through both accesses by a new high-speed infrared (IR) digital imaging system obtaining information that was difficult to achieve by the conventional UV-visible camera. IR camera was able to detect the emitted light in the wavelength range 1.5-5 μm that is relevant for the emission bands of CO₂ and H₂O. The evaporation phase of pre and main injection, and subsequent combustion evolution were analyzed.

The application of an alternative fuel such as hydrogen to internal combustion engines is proving to be an effective and flexible solution for reducing fuel consumption and polluting emissions from engines. An easy to use and immediate application solution is the dual fuel (DF) technology. It has the potential to offer significant improvements in carbon dioxide emissions from light compression ignition engines. The dual fuel concept (natural gas / diesel or hydrogen / diesel) represents a possible solution to reduce emissions from diesel engines by using low-carbon or carbon-free gaseous fuels as an alternative fuel. Moreover, DF combustion is a possible retrofit solution to current diesel engines by installing a PFI injector in the intake manifold while diesel is injected directly into the cylinder to ignite the premixed mixture. In the present study, dual fuel operation has been investigated in a single cylinder research engine.

Nowadays HCCI combustion process is revealing the most useful technique for reducing pollutant emission from internal combustion engines. In the present paper, HCCI combustion was realized by means of single late injection at high pressure and heavy EGR, up to 50%. A transparent Direct Injection (DI) diesel engine equipped with high pressure Common Rail (CR) injection system was used. The engine was fed with commercial diesel fuel and ran in continuous mode. Digital imaging and spectroscopic techniques, with high temporal and spatial resolution, were applied to study the low temperature combustion process. Injection and combustion phases were analysed by digital imaging. Mixing process, autoignition and pollutants formation were investigated by Broadband Ultraviolet - Visible Extinction Spectroscopy (BUVES) and flame emission measurements. Radicals and species such as OH, CH and CO were detected in the combustion chamber.

The management of multiple injections in compression ignition (CI) engines is one of the most common ways to increase engine performance by avoiding hardware modifications and after-treatment systems. Great attention is given to the profile of the injection rate since it controls the fuel delivery in the cylinder. The Injection Rate Shaping (IRS) is a technique that aims to manage the quantity of injected fuel during the injection process via a proper definition of the injection timing (injection duration and dwell time). In particular, it consists in closer and centered injection events and in a split main injection with a very small dwell time. From the experimental point of view, the performance of an IRS strategy has been studied in an optical CI engine. In particular, liquid and vapor phases of the injected fuel have been acquired via visible and infrared imaging, respectively. Injection parameters, like penetration and cone angle have been determined and analyzed.

The present paper describes the results of an experimental activity performed on a small diesel engine for quadricycles, a category of vehicles that is spreading in Europe and is recently spreading over Indian countries. The engine is a prototype three-cylinder with 1000 cc of displacement and it is equipped with a direct common-rail injection system that reaches a maximum pressure of 1400 bar. The engine was designed to comply with Euro 4 emission standard that is a future regulation for quadricycles. It is worth underlining that the engine can meet emission limits just with EGR system and a DOC, without DPF. Various diesel/RME blends were tested; pure diesel and biodiesel fuels were also used. The investigation was carried out at the engine speeds of 1400, 2000 and 3400 rpm and full load. Combustion characteristics of both blended and pure RME were analyzed by means of in-cylinder pressure and heat released histories.

The aim of this study is to investigate the combustion process and pollutant formation in a small compression ignition engine. The engine is a prototype for quadricycles. It was designed to comply with Euro 4 emission standard that is a future regulation for this type of vehicles. Two optical accesses for endoscopes were realized in the first cylinder to investigate the combustion process. Two-color pyrometry method was applied to combustion images in order to detect the flame temperature and the soot concentration. The engine ran with a biodiesel, the rapeseed methyl ester, and a conventional diesel fuel. Operating conditions at the engine speed of 2000 rpm at full and medium load were tested. NOx emissions were measured at exhaust. A smoke meter was used to determine the particulate matter concentration. The sizing and the counting of the particles were performed by means of an engine exhaust particle sizer spectrometer.

This paper deals with the combustion characteristics and exhaust emissions of a diesel engine fuelled with conventional diesel fuel and a biodiesel blend, in particular a 20% v/v concentration of rapeseed methyl ester (RME) mixed with diesel fuel. The investigation was carried out on a prototype three-cylinder engine with 1000 cc of displacement for quadricycle applications. The engine is equipped with a direct common-rail injection system that reaches a maximum pressure of 1400 bar. The engine was designed to comply with Euro 4 and BS IV exhaust emission regulations without a diesel particulate filter. Both in-cylinder pressure and rate of heat release traces were analyzed at different engine speeds and loads. Gaseous emissions were measured at the exhaust. A smoke meter was used to measure the particulate matter concentration. The sizing and the counting of the particles were performed by means of an engine exhaust particle sizer spectrometer.

In the present activity, dual fuel operation was investigated in a single cylinder research engine. Methane was injected in the intake manifold while the diesel was delivered via the standard injector directly into the engine. The aim is to study the effect of increasing methane concentration at constant injected diesel amount on both pollutant emissions and combustion evolution in an optically accessible engine. Emissions are in line with those previously published by other authors, it is noted no PM and constant NOx emissions. Moreover, a decrease of the brake specific CO emissions and an increase of the brake specific THC for the operating condition with the highest premixed ratio was detected. THC was mainly constituted by methane unburned hydrocarbons. Combustion resulted more or less stable. Moreover, via both UV-VIS spectroscopy and digital imaging, the spatial distribution of several species involved in the combustion process was analyzed.