Search Results

Operation of flex fuel vehicles requires operation with a range of fuel properties. The significant differences in the heat of vaporization and energy density of E0-E100 fuels and the effect on spray development need to be fully comprehended when developing engine control strategies. Limited enthalpy for fuel vaporization needs to be accounted for when developing injection strategies for cold start, homogeneous and stratified operation. Spray imaging of multi-hole gasoline injectors with fuels ranging from E0 to E100 and environmental conditions that represent engine operating points from ambient cold start to hot conditions was performed in a spray chamber. Schlieren visualization technique was used to characterize the sprays and the results were compared with Laser Mie scattering and Back-lighting technique. Open chamber experiments were utilized to provide input and validation of a CFD model.

A quantitative and time-resolved technique has been developed to probe the dense spray structure of direct-injection (DI) gasoline sprays in near-nozzle region. This technique uses the line-of-sight absorption of monochromatic x-rays from a synchrotron source to measure the fuel mass with time resolution better than 1 μs. The small scattering cross-section of fuel at x-rays regime allows direct measurements of spray structure that are difficult with most visible-light optical techniques. Appropriate models were developed to determine the fuel density as a function of time.

Liquid and vapor envelopes of sprays from a multi-hole fuel injector operating under closely-spaced double-injection conditions were investigated using a combination of high-speed schlieren and Mie scattering imaging. The effects of mass split ratio and dwell time between injections on liquid and vapor penetration have been investigated under engine-like pressures and temperatures. For the conditions evaluated, the results indicate that closely-spaced double-injection generally reduces liquid and vapor penetration.

Advanced valvetrain coupled with Direct Injection (DI) provides an opportunity to simultaneous reduction of fuel consumption and emissions. Because of their robustness and cost performance, multi-hole injectors are being adopted as gasoline DI fuel injectors. Ethanol and ethanol-gasoline blends synergistically improve the performance of a turbo-charged DI gasoline engine, especially in down-sized, down-sped and variable-valvetrain engine architecture. This paper presents Mie-scattering spray imaging results taken with an Optical Accessible Engine (OAE). OAE offers dynamic and realistic in-cylinder charge motion with direct imaging capability, and the interaction with the ethanol spray with the intake air is studied. Two types of cams which are designed for Early Intake Valve Close (EIVC) and Later Intake Valve Close (LIVC) are tested, and the effect of variable valve profile and deactivation of one of the intake valves are discussed.

With increasingly stringent emissions regulations and concurrent requirements for enhanced engine thermal efficiency, a comprehensive characterization of the automotive gasoline fuel spray has become essential. The acquisition of accurate and repeatable spray data is even more critical when a combustion strategy such as gasoline direct injection is to be utilized. Without industry-wide standardization of testing procedures, large variablilities have been experienced in attempts to verify the claimed spray performance values for the Sauter mean diameter, Dv90, tip penetration and cone angle of many types of fuel sprays. A new SAE Recommended Practice document, J2715, has been developed by the SAE Gasoline Fuel Injection Standards Committee (GFISC) and is now available for the measurement and characterization of the fuel sprays from both gasoline direct injection and port fuel injection injectors.

Increasing the injection pressure in DISI engine is an efficient way to obtain finer droplets but it will also potentially cause spray impingement on the cylinder wall and piston. Consequently, the fuel film sticking on the wall can dramatically increase the soot emission of the engine especially in a cold start condition. On the other hand, ethanol is widely used as an alternative fuel in DI engine due to its sustainable nature and high octane number. In this study, the fuel film characteristics of single-plume ethanol impinging spray was investigated. The experiments were performed under ultra-low fuel/plate temperature to simulate the cold start condition in cold areas. A low temperature thermostatic bath combined with specially designed heat exchangers were used to achieve ultra-low temperature for both the impinging plate and the fuel. Laser induced fluorescence (LIF) technique was employed to measure the thickness of fuel film deposited on the impinging plate.

This work investigates the injection processes of an eight-hole direct-injection gasoline injector from the Engine Combustion Network (ECN) effort on gasoline sprays (Spray G). Experiments are performed at identical operating conditions by multiple institutions using standardized procedures to provide high-quality target datasets for CFD spray modeling improvement. The initial conditions set by the ECN gasoline spray community (Spray G: Ambient temperature: 573 K, ambient density: 3.5 kg/m3 (∼6 bar), fuel: iso-octane, and injection pressure: 200 bar) are examined along with additional conditions to extend the dataset covering a broader operating range. Two institutes evaluated the liquid and vapor penetration characteristics of a particular 8-hole, 80° full-angle, Spray G injector (injector #28) using Mie scattering (liquid) and schlieren (vapor).

Liquid and vapor penetration of sprays from a multi-hole gasoline fuel injector operating under engine-like conditions were systematically investigated utilizing a high-speed imaging system capable of acquiring schlieren and Mie scattering images in a near-simultaneous fashion. The influences of ambient conditions and fuel properties on the formation of liquid and vapor envelopes were evaluated. In addition to the compilation of an extensive data set, results of the investigation indicate that mixing-limited vaporization modeling can be utilized to predict the maximum liquid penetration of short-duration, multi-plume sprays.

Catalyzed gasoline particulate filter (cGPF) is the prime technology to meet future stringent regulations for particulates from gasoline direct injection (GDI) engines. One of the technical concerns is the ultimate durability of cGPF in regards to engine lubricant formulations. This study investigated two tailored lubricant formulations on catalyzed GPFs which were aged on engine followed by emission testing on vehicle. An engine accelerated aging protocol was developed for cGPFs to simulate thermal aging, ash and soot loading that is at least equivalent to 200,000 km durability requirement. Evaluations include tailpipe emission levels, backpressure, catalytic performance, and post-mortem analysis. Both formulations have demonstrated a high level of cGPF performance retention; performance being assessed in terms of emission level at the end of durability demonstration testing. These formulations provide flexibility in selecting robust lubricant to meet various system requirements.

Effects of fuel cell material properties on water management were numerically investigated using Volume of Fluid (VOF) method in the FLUENT. The results show that the channel surface wettability is an important design variable for both serpentine and interdigitated flow channel configurations. In a serpentine air flow channel, hydrophilic surfaces could benefit the reactant transport to reaction sites by facilitating water transport along channel edges or on channel surfaces; however, the hydrophilic surfaces would also introduce significantly pressure drop as a penalty. For interdigitated air flow channel design, it is observable that liquid water exists only in the outlet channel; it is also observable that water distribution inside GDL is uneven due to the pressure distribution caused by interdigitated structure. An in-situ water measurement method, neutron imaging technique, was used to investigate the water behavior in a PEM fuel cell.

Companion empirical and analytical studies were conducted to assess the feasibility and constraints (hardware and combustion perspectives) associated with operating a Spark Ignition Direct-Injection (SIDI) engine on high ethanol and gasoline mixtures ranging from 0 to 85% by volume. Cold start, part and full-load performance aspects were explored. Analytical experiments were performed to correlate with the empirical data using a commercially available single dimensional engine simulation code. Under WOT operating conditions it was found that the engine's simulated output was overestimated with E85 fuel which was caused by the over prediction of volumetric efficiency. It was necessary to create a sub-routine to accurately model the impingement, vaporization, and heat transfer of fuel on the piston surface. Results could only be correlated after taking fuel impingement into account.

Catalyzed gasoline particulate filters (cGPF) are one of the most effective emission control technologies for reducing gaseous and particulate emissions simultaneously. Successful adoption of this advanced technology relies on several important performance properties including low back pressure, high filtration efficiency and specially durability compliance. In this work using an underfloor cGPF, the backpressure control was achieved through optimizing catalyst coating technology and modifying the deposition profile of catalyst coating along GPF channels. Durability performance was demonstrated by using an accelerated engine aging method with selective blending of lubricating oils in fuel, which incorporates the aging mechanisms of thermal aging, ash loading, and soot accumulation/regeneration. The target durability demonstration represents 200,000 km real world operation.

Requirements for reduced fuel consumption with simultaneous reductions in regulated emissions require more efficient operation of Spark Ignited (SI) engines. An advanced valvetrain coupled with Gasoline Direct injection (GDi) provide an opportunity to simultaneously reduce fuel consumption and emissions. Work on a flex fuel GDi engine has identified significant potential to reduce throttling by using Early Intake Valve Closing (EIVC) and Late Intake Valve Closing (LIVC) strategies to control knock and load. High loads were problematic when operating on gasoline for particulate emissions, and low loads were not able to fully minimize throttling due to poor charge motion for the EIVC strategy. The use of valve deactivation was successful at reducing high load particulate emissions without a significant airflow penalty below 3000 RPM. Valve deactivation did increase the knocking tendency for knock limited fuels, due to increased heat transfer that increased charge temperature.

Because of their robustness and cost performance, multi-hole gasoline injectors are being adopted as the direct injection (DI) fuel injector of choice as vehicle manufacturers look for ways to reduce fuel consumption without sacrificing power and emission performance. To realize the full benefits of direct injection, the resulting spray needs to be well targeted, atomized, and appropriately mixed with charge air for the desirable fuel vapor concentration distributions in the combustion chamber. Ethanol and ethanol-gasoline blends synergistically improve the turbo-charged DI gasoline performance, especially in down-sized, down-sped and variable-valve-train engine architecture. This paper presents the spray imaging results from two multi-hole DI gasoline injectors with different design, fueled with pure ethanol (E100) or gasoline (E0), under homogeneous and stratified-charge conditions that represent typical engine operating points.

Multi-hole DI injectors are being adopted in the advanced downsized DISI ICE powertrain in the automotive industry worldwide because of their robustness and cost-performance. Although their injector design and spray resembles those of DI diesel injectors, there are many basic but distinct differences due to different injection pressure and fuel properties, the sac design, lower L/D aspect ratios in the nozzle hole, closer spray-to-spray angle and hense interactions. This paper used Phase-Contrast X ray techniques to visualize the spray near a 3-hole DI gasoline research model injector exit and compared to the visible light visualization and the internal flow predictions using with multi-dimensional multi-phase CFD simulations. The results show that strong interactions of the vortex strings, cavitation, and turbulence in and near the nozzles make the multi-phase turbulent flow very complicated and dominate the near nozzle breakup mechanisms quite unlike those of diesel injections.

Because of the increased use of gasoline direct engine (GDI) in the automobile industry, there is a significant need to control particulates from GDI engines based on emission regulations. One potential technical approach is the utilization of a gasoline particulate filter (GPF). The successful adoption of this emission control technology needs to take many aspects into consideration and requires a system approach for optimization. This study conducted research to investigate the impact of vehicle driving cycles, fuel properties and catalyst coating on the performance of GPF. It was found that driving cycle has significant impact on particulate emission. Fuel quality still plays a role in particulate emissions, and can affect the GPF performance. Catalyzed GPF is preferred for soot regeneration, especially for the case that the vehicle operation is dominated by congested city driving condition, i.e. low operating temperatures. The details of the study are presented in the paper.