Search Results

This paper describes an analysis of the rise in timing belt temperature occuring under high engine speed operation that was made to establish the cause of heat deterioration of the belt materials. Surface temperatures of the belt were accurately measured by correcting thermo-vision detected radiations to eliminate environmental radiation. The temperature profile of a belt cross-section was obtained by a specially developed thermo-couple device. The experimental results indicated that heat generated by the belt contributes significantly to the temperature rise and that the primary cause of the heat generation is bending hysteresis of the belt cords. In addition, a description is made of a method of calculating the rate of heat generation in the belt. In this simulation method, the energy dissipated as heat is calculated from the bending strains and loss moduli of the belt materials. Calculated results were found to agree well with experimental results.

A television viewing system with a high speed shutter TV camera has been developed for viewing and recording combustion processes in internal combustion engines. The technique has been applied to the study of combustion events in an engine with a transparent piston. The recorded combustion images were analyzed and statistically processed by a microcomputer for summation, averaging, and contour forming. The averaged flame propagation patterns are discussed in comparison with the gas flow motion and cylinder pressure data obtained by conventional methods. This TV technique is easy and effective in obtaining combustion data for various operating conditions and engine geometries.

A new stratified charge combustion system has been developed for direct injection gasoline engines. The special feature of this system is employment of a thin fan-shaped fuel spray formed by a slit nozzle. The stratified mixture is produced by the combination of this fan-spray and a shell-shaped piston cavity. Both under-mixing and over-mixing of fuel in the stratified mixture is reduced by this system. This combustion system does not require distinct charge motion such as tumble or swirl, which enables intake port geometry to be simplified to improve full load performance. The effects of the new system on engine performance at part load are improved fuel consumption and reduced smoke, CO and HC emissions, obviously at medium load and medium engine speed. HC emissions at light load are also improved even with high EGR conditions.

An ultra-high speed shutter TV camera including an image intensifier which has a light magnification of 20,000, and an image analysis system have been developed and applied to knock research with a transparent piston engine. Irregularity in the flame configuration was observed just when the pressure vibration began. The causes of cycle to cycle variation of knock intesity were examined through the simultaneous recording of the pressure vibration and the image of the flame.

In order to reduce tail-pipe hydrocarbon emissions from SI gasoline engines, rapid catalyst warm-up and improvement of catalyst conversion efficiency are important. There are many reports which have been published by manufacturers and research institutes on this issue. For further reduction of tail-pipe hydrocarbon emissions, it is necessary to reduce engine-out hydrocarbon emissions and to improve after treatment, during the time the catalyst is not activated. This paper quantitatively analyzed the fuel amount of intake port and cylinder wall-wetting, burned fuel and engine-out hydrocarbon emissions, cycle by cycle in firing condition, utilizing a specially designed analytical engine. The effect of mixture preparation and fuel properties for engine-out hydrocarbon emissions, during the cold engine start and warm-up period, were quantitatively clarified.

A two-color high speed shutter TV camera system has been developed as a new sensing device for measuring the flame temperature in engines. The TV camera system can measure the radiant intensities of high temperature substances accurately and rapidly. And, the two-dimensional temperature distribution can be easily calculated from the radiant intensities by using an image processor. This system is applicable to measurement of flame temperatures in diesel and gasoline engines. The relation between the progress of combustion phenomena and the measured temperature distribution is clearly explained. It is confirmed that the system is effective for measurement of the flame temperature distribution in engines.

Effects of spray characteristics for stratified combustion of direct injection gasoline engine have been researched. The highly functional piezoelectric (PZT) injector was selected for this research. A hole and swirl nozzle were examined in a wide range of fuel pressure. The hole nozzle aims to make stratified mixture formation by vaporizing fuel on the piston, and the swirl nozzle aims to do so in the air above the piston by utilizing the spray characteristic of lower penetration and higher dispersibility. Both sprays could realize stable stratified combustion. The stability mainly depends on the combination of spray characteristic and piston cavity shape, and the swirl air motion which strength changes corresponding to engine operating conditions. The hole nozzle requires high, and the swirl nozzle less fuel pressure. Even by a large amount of EGR, stratified combustion has the advantage of combustion stability, and is useful to reduce exhaust emissions, especially NOx emissions.

A direct injection (DI) gasoline engine having a new stratified charge combustion system has been developed. This new combustion process (NCP) was achieved by a fan-shaped fuel spray and a combustion chamber with a shell-shaped cavity in the piston. Compared with the current Toyota D-4 engine, wider engine operating area with stratified combustion and higher output performance were obtained without a swirl control valve (SCV) and a helical port. This report presents the results of combustion analyses to optimize fuel spray characteristics and piston cavity shapes. Two factors were found to be important for achieving stable stratified combustion. The first is to create a ball-shaped uniform mixture cloud in the vicinity of the spark plug. The optimum ball-shaped mixture cloud is produced with a fuel spray having early breakup characteristics and uniform distribution, and a suitable side wall shape in the piston cavity to avoid the dispersion of the mixture.

A newly-developed time resolved exhaust gas analysis system was utilized in this study. The hydrocarbon compositions upstream and downstream of the catalytic converter were investigated during cold start and warm up of the Federal Test Procedure(FTP), with three fuels of different aromatic contents. Although engine-out hydrocarbon emissions had high concentrations right after cold start, the specific reactivity was low. This can be explained by the selective adsorption of the high boiling point components which had a high Maximum Incremental Reactivity (MIR) in the intake manifold and engine-oil films. Thereafter, the high boiling point components were desorbed rapidly and consequently specific reactivity increased. Hydrocarbon adsorption of high boiling point components and hydrocarbon conversion of low boiling point components occurred simultaneously on the catalyst during warm up.

In SI engines with port injection system, fuel behavior both in the intake port and in the cylinder has significant influence on the transient A/F characteristics and HC emissions [1]. Therefore, to improve the engine performance, it is very important to understand fuel behavior in the intake port and in the cylinder [2, 3]. This paper describes the following three unique methods to analyze fuel behavior in port injected SI engines and some test results. (1) Observation of fuel behavior in the intake port, using a transparent intake air tube and a strobe synchronized TV-photographic system. (2) Observation of fuel behavior in the cylinder, using a glass cylinder and fluorescent fuel. (3) Measurement of fuel wall wetting in the intake port and in the cylinder, using the engine with electronically controlled hydraulically driven in-take/exhaust valves.