Search Results

TFC/IW, total fuel consumption divided by inertia weight is reported with other engineering variables for recent EPA data for industry passenger cars and truck. TFC/IW is used in comparisons between gasoline and diesel engines, 49 States and California, passenger cars and trucks. The California fuel economy penalty due to more stringent emissions standards is discussed. The relationship between TFC/IW and ton miles per gallon is shown. Special attention is focused on 4 cylinder gasoline powered vehicles in 49 States passenger car fleet. The use of TFC/IW to answer the question, ‘What Changed?’ when comparing the fuel economies of two fleets is described.

IT does not yet seem to be recognized fully that it is the local temperature at the surface of contact and not the local specific pressure that chiefly determines the occurrence of seizure under extreme-pressure-lubrication conditions. This local temperature is the result of the temperature level of the parts lubricated, considered as a whole (“bulk” temperature) and of a superimposed instantaneous temperature rise (temperature “flash”) which is localized in the surface of contact. It appears typical for extreme-pressure-lubrication conditions, as met in gear practice, that the temperature flash is much higher than the bulk temperature. With existing conventional test methods for the determination of the protection against seizure afforded by EP lubricants, a considerable rise of the bulk temperature mostly occurs; as it cannot be controlled sufficiently; thus, leaving an unknown margin for the temperature flash, it renders impossible a reliable determination.

A survey of the in-service fuel consumption of passenger vehicles and derivatives in the Australian fleet was carried out in 1984-85. Seven hundred and four owners across Australia took part in the survey. Vehicle owners reported by questionnaire the amount of fuel used during four tank fills of normal operation, the distance travelled, and other details of the operating circumstances. The survey shows a clear downward trend in the fuel consumption of the Australian passenger fleet. The data also provides comparisons of actual fuel consumption obtained on the road, with laboratory derived values for fuel consumption. Vehicles in a sub-set of 40 were fitted with fuel flow meters during the survey and tested to Australian Standard 2077 for fuel consumption. The questionnaire method is shown to be a valid and accurate technique for determining in-service fuel consumption.

Diesel propulsion of commercial vessels burning “heavy fuel” on the Great Lakes, for one operator, has come about by an evolution beginning in 1951 and culminating in 1, 000′ LOA vessels burning intermediate fuels, pre-blended using residual and distillate mixtures, in large medium speed, heavy duty diesel engines.

In recent years there has been increasing interest in quantifying the emissions from aircraft in order to generate inventories of emissions for climate models, technology and scenario studies, and inventories of emissions for airline fleets typically presented in environmental reports. The preferred method for calculating aircraft engine emissions of NOx, HC, and CO is the proprietary “P3T3” method. This method relies on proprietary airplane and engine performance models along with proprietary engine emissions characterizations. In response and in order to provide a transparent method for calculating aircraft engine emissions non proprietary fuel flow based methods 1,2,3 have been developed. This paper presents derivation, updates, and clarifications of the fuel flow method methodology known as “Fuel Flow Method 2”.

With the increase in demand for energy sustainability projects over the last few years, the Brazilian commercial vehicle industry was guided to develop projects based on ESG policies. Aligned with this need, an initiative that ended up becoming a reality was the “e-Sys” electrification solution, by the company Suspensys. This solution includes a power source (battery), an e-powertrain (motors, inverters and drive axle) and an intelligent control system (VCU with embedded code and sensors). The main motivational drive was the hybridization of semi-trailers, in order to generate a reduction in fuel consumption in cargo transport in Brazil, in addition to the consequent reduction in the emission of particles into the environment and promoting the safety of the operation. It was also adopted, as a premise of the project, that the electrification system was totally independent of the truck’s electronic system (stand alone system), in order to facilitate the operation of the fleet owner.

The trend towards renewable energy sources will continue under the pre-amble of greenhouse gas (GHG) emission reduction targets. The main question is how to harvest and store renewable energy properly. The challenge of intermittency of the renewable energy resources make the supply less predictable compared to the traditional energy sources. Chemical energy carriers like hydrogen and synthetic fuels (e-Fuels) seem to be at least a part of the solution for storing renewable energy. The usage of e-Fuels in the existing ICE-powered vehicle fleet has a big lever arm to reduce the GHG emissions of the transport sector in the short- and medium term. The paper covers the whole well-to-wheel (WtW) pathway by discussing the e-Fuel production from renewable sources, the storage and the usage in the vehicle. It will be summarized by scenarios on the impact of e-Fuel to the WtW CO2 fleet emissions.

This paper discusses the advantages and problems associated with the use of “passive” liquid containment systems that utilize liquid intermolecular forces for propellant orientation in reduced or zero gravity environments. Liquid orientation is required to provide reliable engine restart and tank venting operations of space vehicle propulsion systems. Various liquid containment system concepts, and associated design criteria, are presented and general problem areas of interface stability, liquid slosh, and effects of thermal energy are described. Descriptions of present and planned test facilities designed to provide reduced gravity environments and extended time durations are included. It is concluded that additional design criteria in the problem areas discussed must be obtained before “passive” liquid containment systems can replace systems now used in reduced or zero gravity environments.

Instantaneous combine grain yield monitors need to provide reliable yield measurements since yield as a function of location is key information needed to manage fields by management zones. A scale and a yield monitor measured the same stream of grain and provided similar results when compared to each other. Data from either device may be misinterpreted if care in calibration and operation is not taken. Careful operators who pay attention to calibration, maintenance, and manufacturer's instructions will be required.

XEROX has developed and implemented a network architecture for a real time control system which has expansion flexibility, high reliability, noise immunity, and low cost. This two level multiplex system with a single wire system bus at one level for distributed processors connected to local serial buses at the second level for remote functions and loads is described. The XEROX Microelectronics Center has developed a set of custom VLSI chips to implement the multiplexing architecture. Control software was developed using both assemblers and high level language tools. The software and chip set have been designed, built and integrated into XEROX'S latest generation of products.

The wide variety of available leadless electronic components is described. Some typical applications of these devices are illustrated. The advantages to be gained through the use of these surface mounted devices are explained. These include reduced size, increased reliability, improved performance and reduced cost. Methods of application, including automatic assembly equipment, are discussed. Several applicable soldering processes are explained.

Work solenoids are widely used in household appliances. The environment and design of this type application does not lead to solenoids for the earthmoving industry. This paper presents the environmental effects to be considered when designing a solenoid for the earthmoving industry. It further explains the need for, and type of, test necessary to validate the design. Finally a review of production quality procedures, necessary to insure reliable production parts is discussed.

A bioregenerative diet is characterized by a high proportion of foods produced on site. The production and processing of foods into either ingredients or recipes entails certain labor requirements. Ideally these labor requirements should be estimated with a high degree of accuracy. Crew time is at premium and any amount of time spent on food preparation and processing is time not spent in conducting research and any other activities devised to improve the quality of life of the astronauts. Moreover, a wide variety of tasks are involved in the food preparation of a bioregenerative diet and the labor times of these tasks do not scale or increase in uniform fashion. Predicting food preparation labor requirements for varying crew sizes will require task specific models and data. Videotape analysis is a work measurement tool used in the manufacturing industry.

Due to the rapid development in the technological aspect of the autonomous vehicle (AV), there is a compelling need for research in the field vehicle efficiency and emission reduction without affecting the performance, safety and reliability of the vehicle. Electric vehicle (EV) with rechargeable battery has been proved to be a practical solution for the above problem. In order to utilize the maximum capacity of the battery, a proper power management and control mechanism need to be developed such that it does not affect the performance, reliability and safety of vehicle. Different optimization techniques along with deterministic dynamic programming (DDP) approach are used for the power distribution and management control. The battery-operated electric vehicle can be recharged either by plug-in a wired connection or by the inductive mean (i.e. wirelessly) with the help of the electromagnetic field energy.

Discussion in this paper is centered on general problems of subarctic operation, results of the 1968-1969 winter testing at Ft. Churchill, Manitoba, Canada, and the testing planned for the 1969-1970 season at Ft. Churchill. Significant findings from the 1968-969 testing indicate the vital importance of care in preparation of vehicles for the arctic, the need for greater simplicity and reliability in design of winterization systems, and the inadequacy of currently used elastomeric components (hoses, o-rings, etc.).

Winter testing of cars and tires for consumer comparisons is not an easy task to begin with; this is further complicated by the fact that reliable methods for evaluating performance and access to good testing conditions are unavailable to most magazines. The testing group at Tekniikan Maailma Magazine, Finland, has been fortunate to have both the right conditions as well as reasonable resources to develop methods of testing to the extent that they provide sufficiently reliable data to assess vehicle and tire performance in winter conditions. Before any final evaluations are published in the magazine, the weighing of different factors, i.e. the amount of importance placed on different performance characteristics, is carefully considered. In order to achieve a meaningful ranking of these products in relation to different characteristics, constant reference runs, statistical research methods, and highly skillful test drivers are employed.

The use of devices to reduce aerodynamic drag on large trailers and save fuel in long-haul, over-the-road freight operations has spurred innovation and prompted some trucking fleets to use them in combinations to achieve even greater gains in fuel-efficiency. This paper examines aerodynamic performance and potential drag reduction benefits of using trailer aerodynamic components in combinations based upon wind tunnel test data. Representations of SmartWay-verified trailer aerodynamic components were tested on a one-eighth scale model of a class 8 sleeper tractor and a fifty three foot, van trailer model. The open-jet wind tunnel employed a rolling floor to reduce floor boundary layer interference. The drag impacts of aerodynamic packages are evaluated for both van and refrigerated trailers. Additionally, the interactions between individual aerodynamic devices is investigated.

Dragfoiler II, an effective and practical add-on aerodynamic drag reducing system for tractor-trailers, has been developed. Wind tunnel tests with 1/16- and 1/7-scale tractor-trailer models were used to determine empirical design guidelines for the Dragfoiler II's side elevation and planform shapes. Optimum designs for various combinations of tractor roof height and length, trailer height, and tractor-to-trailer gap length gave zero-yaw drag reductions between 30 and 35%. At a yaw angle of 10°, the percentage drag reductions were about half those at 0°. Off-design performance and the effects of trailer side-edge geometry were investigated. Several full-scale Dragfoiler II's are currently undergoing proving ground and commercial fleet evaluation tests.

Through this work, Wind River and Airbiquity look to enable secure and intelligent software updates and data management for these vehicles through over-the-air (OTA) programming technology. The work may also lead to similar solutions for traditional aerospace and unmanned aircraft system (UAS) industries.