Search Results

Standard

Vehicle Lift Points for Service Garage Lifting

2019-10-16

CURRENT

J2184_201910

This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.

Standard

Vehicle Lift Points for Service Garage Lifting

2007-09-27

HISTORICAL

J2184_200709

This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.

Standard

Towing Equipment Ratings and Practices

1999-08-01

HISTORICAL

J2512_199908

This SAE Recommended Practice applies to all trucks that are equipped with armlift bodies, carrier bodies, wheel lift bodies, wrecker, and underlift bodies. Additional rating methods are provided for tow slings, truck hitches, and chain assemblies.

Standard

Towing Equipment Ratings and Practices

2019-10-24

CURRENT

J2512_201910

This SAE Recommended Practice applies to all trucks that are equipped with armlift bodies, carrier bodies, wheel lift bodies, wrecker, and underlift bodies. Additional rating methods are provided for tow slings, truck hitches, and chain assemblies.

Standard

Towability Design Criteria and Equipment Use - Passenger Cars, Vans, and Light-Duty Trucks

2019-10-28

CURRENT

J1142_201910

This SAE Recommended Practice describes the type of equipment commonly used with towing equipment, provides information to calculate safe steering loads, and outlines design criteria.

Standard

TOWABILITY DESIGN CRITERIA AND EQUIPMENT USE— PASSENGER CARS, VANS, AND LIGHT-DUTY TRUCKS

1994-02-02

HISTORICAL

J1142_199402

This SAE Recommended Practice describes the type of equipment commonly used with towing equipment, provides information to calculate safe steering loads, and outlines design criteria.

Standard

Seat Belt Restraint System Hardware - Glossary of Terms

2013-01-08

HISTORICAL

J1803_201301

This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.

Standard

Seat Belt Hardware Performance Requirements

2013-02-13

HISTORICAL

J141_201302

This SAE Recommended Practice describes performance requirements for hardware used in motor vehicle seat belt assemblies when tested in accordance with the test procedures specified in SAE J140. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.

Standard

Numbering Systems for End Mills

2019-10-09

CURRENT

J2342_201910

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering Systems for End Mills

1999-01-20

HISTORICAL

J2342_199901

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Taps

1998-10-14

HISTORICAL

J2123_199810

This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Taps

2019-10-09

CURRENT

J2123_201910

This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Single Diameter and Taper Reamers

2019-10-09

CURRENT

J2124_201910

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Single Diameter and Taper Reamers

1998-10-14

HISTORICAL

J2124_199810

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Single Diameter Drills

2019-10-09

CURRENT

J2122_201910

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Single Diameter Drills

1998-10-14

HISTORICAL

J2122_199810

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Multiple Diameter Cutting Tools

2019-10-09

CURRENT

J2276_201910

This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

Numbering System for Multiple Diameter Cutting Tools

1998-10-13

HISTORICAL

J2276_199810

This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

Standard

NUMBERING SYSTEM FOR STANDARD TAPS

1990-11-01

HISTORICAL

J2123_199011

This SAE Recommended Practice provides a systematic method for the identification of standard taps. It is intended to assist in the cataloging and supplying of these tools. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).

Standard

NUMBERING SYSTEM FOR STANDARD DRILLS

1990-11-01

HISTORICAL

J2122_199011

This SAE recommended practice provides a systematic method for the identification of standard drills. It is intended to assist in the cataloging and supplying of these tools. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).