Search Results

This paper sets up a simplified dynamic model for simulating the yaw/roll stability of heavy tractor-semitrailer using Matlab/Simulink. A linear quadratic regulator (LQR) based on partial-state feedback controller is used to optimize the roll stability of the vehicle. The control objective for optimizing roll stability is to be reducing the lateral load transfer rate while keeping the suspension angle less than the maximum allowable angle. The simulation result shows that the LQR controller is effective in the active roll stability control of the heavy tractor-semitrailer.

Steering-By-Wire (SBW) system has advantages of advanced vehicle control system, which has no mechanical linkage to control the steering wheel and front wheels. It is possible to control the steering wheel actuator and front wheels actuator steering independently. The goal of this paper is to use a joystick to substitute the conventional steering wheel with typical vehicle SBW system and to study a variable steering ratio design method. A 2-DOF vehicle dynamic reference model is built and focused on the vehicle steering performance of drivers control joystick. By verifying the results with a hardware-in-the-loop simulation test bench, it shows this proposed strategy can improve vehicle maneuverability and comfort.

The tire mechanics characteristics are essential for analysis, simulation and control of vehicle dynamics. This paper develops the UniTire model for tire forces and moments under combined slip conditions with anisotropic tire slip stiffness. The anisotropy of tire slip stiffness, which means the difference of tire longitudinal slip stiffness and cornering stiffness, will cause that the direction of tire resultant shear stress in adhesion region is different from that in sliding region. Eventually the tire forces and moments under combined slip conditions will be influenced obviously. The author has proposed a “direction factor” before to modify the direction of resultant force in the tire-road contact patch, which can describe tire forces at cornering/braking combination accurately. However, the aligning moments which are very complicated under combined slip conditions are not considered in previous analysis.

To improve the quantitative accuracy of vehicle vibration studies, a roller contact tire model with the geometric filtering concept and a method to determine the effective road input are proposed. Computer simulation with the 13 DOF vehicle model for a light truck, based on two different tire models, and relevant outdoor tests for measuring the vehicle accelerations of both sprung and unsprung masses are presented. Comparisons of test data and simulation results show that the roller contact tire model renders much better simulation accuracy than the single point contact tire model. It is concluded that the roller contact tire model is a powerful concept which acts as a geometric filter, giving a simple method to calculate the enveloping effects of tires and the effective road elevation input.

This paper presents a study on steering effort preference of Chinese drivers based on ADSL Driving Simulator. The results of the simulation test demonstrates that Chinese drivers' steering effort preference increases with vehicle speed, which is similar to European and Japanese drivers', but the mean preference effort level itself is lower than that of European and Japanese drivers' and this same steering effort preference increases obviously with lateral acceleration in linear region (lateral acceleration level lower than 0.3g) while not as evidently in nonlinear region (lateral acceleration level higher than 0.3g).

In order to improve the braking energy recovery, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established by co-simulation platform for the TruckSim and Matlab/Simulink in this paper. EBS makes the front and rear shaft braking force arbitrarily distributed, which is more effective to improve the rate of energy recovery and the braking stability. A braking force distribution algorithm for hybrid electric bus based on EBS was designed in this paper. Under the premise to meet the driver's needs and the ECE regulations, this braking force distribution method focuses on making the braking force distribute to the drive shaft to a maximum extent, so as to obtain the maximum energy recovery rate by the utilization of the motor regenerative braking. At last, the simulation in different operating conditions was used to analyze the braking energy utilization and the braking performance based on the simulation model.

Simulations of tire cornering properties with small-amplitude lateral inputs are carried out in non-steady state conditions. The simulation algorithm is derived and the discrete expressions are presented in detail. Based on the simulations, lateral force and aligning moment can be calculated numerically with time-varying yaw angle and lateral displacement as inputs in spatial domain. The flexibility of both tread and carcass along with tire width is taken into account effectively in the simulations, in which the flexibility of carcass includes translating, bending and twisting flexibility. The simulations in non-dimensional form are associated with four tire structure parameters only, which are non-dimensional parameters reflecting the characteristics of tire stiffness, tire width and contact length. Simulation results are validated by test data from step lateral inputs tests. Several typical simulation results are provided.

With rapid development of the automobile industry and the growing maturity of the automotive electronic technologies, the distributed-traction electric vehicle with four-wheel-distributed steering/braking/traction systems is regarded as an important development direction. With its unique chassis structure, it is the ideal benchmark platform used to evaluate active safety systems. The distributed-traction electric vehicle with four-wheel-distributed steering system is essentially full drive-by-wire vehicle. With its flexible chassis layout and high control degrees-of-freedom, the full drive-by-wire electric vehicle acted as a kind of redundant system is an ideal platform for the research of integrated control. In this treatise, the longitudinal dynamics of the electric vehicle as well as its lateral and yaw motions are controlled simultaneously.

The commercial vehicle is widely used in the overland transport. A prediction is given on the 9th annual China automotive industry forum that the number of the global commercial vehicles will reach eight million by the year of 2016. However, since the distance between its gravity centre and the ground is larger than that of the passenger vehicle, considering its comparatively short wheelbase, the rollover accident, which is fatal to the drivers and always makes enormous loss of merchandises, easily occurs in the case of commercial vehicles. As the number of the commercial vehicle is increasing fast, the accidents will occur more frequently, the losses will be increasingly enormous. To solve the problem, many researches about rollover early warning systems have been done. In most cases, it is assumed that the references of the vehicle are given.

A closed-loop comprehensive evaluation and a test method for vehicle handling and stability have been studied by using development driving simulator. Simulator test scheme has been designed and carried out with 14 vehicle configurations, and subjective evaluation has been made for easy handling of vehicle by drivers. A closed-loop comprehensive evaluation index has been put forward considering the factors affecting vehicle handling and stability. The reliability of the index has been validated by driver's subjective evaluation. A driver/vehicle/ road closed-loop system model has been established, and the theoretical predictive evaluation has been carried out with 14 vehicle configurations. Simulation showed that similar result for both theoretical predictive evaluation and subjective evaluation.

The simulation of electro-pneumatic components used in brake systems of commercial vehicles is of great importance in order to understand their characteristics for developing a control logic and improve the braking performance. As the goal of improving the performance of the commercial vehicle pneumatic EBS(Electronically controlled Braking System), static and dynamic characteristics of proportional relay valve for commercial vehicle pneumatic EBS have been simulated by using MATLAB/Simulink environment and validated by testing on hardware-in-the-loop test bench focused on its pressure hysteresis characteristic. The simulation and test results show that the mathematic model for proportional relay valve characteristics is reasonable and reliable, and this simulation tool can be used for research and developing of pneumatic EBS system for commercial vehicle effectively.

This paper presents a torque distribution algorithm to improve the energy efficiency of four-wheel-drive (4WD) electric vehicles with PMSM hub motors. In order to optimize the torque distribution method, at first the motor model considering the affect of iron loss and the loss model of multi-motors drive system of 4WD electric vehicle with PMSM hub motors, which operate at straight-line condition, are established. Besides, realize the online identification of motor parameters based on the MARS, which is important for updating the loss model parameters of the motor drive system. By doing this, the ideal torque distribution ratio can be obtained from the loss model in real-time. The simulation result using different distribution algorithms shows that the optimized torque distribution algorithm based on the loss model can be useful for improving the energy efficiency.

In the paper, the Flat Plank Tire Tester of Changchun Automobile Institute is introduced. This paper, according to practical experiences, generalizes some issues in the tire's non-steady state test. In the non-steady state test, it must be assured that the footprint centerline of tire coincides with that of slid platform, which guarantees no sliding motion between tire and slid platform during the movement. Due to tire taper effect and inhomogeneous tire material, when its side slip angle is zero, side force and aligning torque are not zeros, but have initial values. Here two approaches are discussed to eliminate the side force and aligning torque. Besides, other factors in the test are put forward for discussion. Eliminating the interference can obviously improve the test accuracy. This paper also provides test curves of both pure side slip angle input and pure yaw angle input.

A new electric power steering system (EPS) dynamic friction model based on normalized Bouc-Wen model is given, as well as its structure form and model features. In addition, experimental method is used to identify corresponding parameters. In order to improve road feel feedback, this paper analyzes the shortcoming of traditional constant friction compensation control method and proposes a variable friction compensation control method which the friction compensation current changes according to the assist characteristic gain. Through simulation and real vehicle test verification, variable friction compensation control method eliminates the effect of basic assist characteristic, and improves the driver’s road feel under high speed.

Pneumatic Electric Braking System (EBS) is getting widely spread for commercial vehicles. Pneumatic EBS improves the problem of slow response of traditional pneumatic braking system by implementing brake-by-wire. However, the time-delay response and hysteresis of some electro-pneumatic components and some other issues decrease the response and control accuracy of the pneumatic EBS.

This paper first presents an algorithm to detect tire blowout based on wheel speed sensor signals, which either reduces the cost for a TPMS or provides a backup in case it fails, and a tire blowout model considering different tire pressure is also built based on the UniTire model. The vehicle dynamic model uses commercial software CarSim. After detecting tire blowout, the active braking control, based on a 2DOF reference model, determines an optimal correcting yaw moment and the braking forces that slow down and stop the vehicle, based on a linear quadratic regulator. Then the braking force commands are further translated into target pressure command for each wheel cylinder to ensure the target braking forces are generated. Some simulations are conducted to verify the active control strategy.

Electronic braking system (EBS) of commercial vehicle is developed from ABS to enhance the brake performance. Based on the early development of controller hardware, this paper starts with an analysis of the definition of EBS. It aims at the software design of electronic control unit, and makes it compiled into the controller in the form of C language by the in-depth study about control strategy of EBS in different braking conditions. Designed controller software is divided into two layers. The upper control strategy includes the recognition algorithm of driver's braking intention, estimation algorithm of the vehicle state, conventional braking strategy which consists of the algorithm of deceleration control and braking force distribution, and emergency braking strategy which consists of the algorithm of brake assist control and ABS control.

This essay aims to develop an electrically controlled steering test bench and lay a solid foundation for the development of steering system. The first part mainly introduces the function, structure and working principle of the test bench. For the hardware system, it includes the steering system, fixture, sensors as well as a frameless disk motor for carrying out automatic motor input, and a dual linear motor system selected as the road resistance simulation actuator. As for the software, MATLAB/Simulink, CarSim, RTI and ControlDesk are used. Therefore, with the help of real-time simulation platform, researchers can not only build control strategy and dynamic model but also control the experiment and tune parameters in real-time. The second part of the essay aims to identify both electric and mechanical parameters of R-EPS system by carrying out tests on the proposed test bench. As parameters are successfully identified, the feasibility of the test bench is also verified.

This paper presents an adaptive observer-based approach for the combined state estimation and active fault detection and isolation (FDI) of the individual-wheel-drive (IWD) vehicles. A 3-DOF vehicle model coupled with the Highway Safety Research Institute (HSRI) tire model is established and used as the observation model. Based on this model, the dual unscented Kalman filter (DUKF) technique is employed for the observer design to give fusion results of the interdependent state and parameter variables, which undergo nonlinear transformations, with the minimum square errors. Effectiveness of the proposed algorithm is examined and validated through co-simulation between MATLAB/Simulink and CarSim. The results demonstrate that the DUKF-based observer effectively filters the sensor signals, accurately obtains the longitudinal and lateral velocities, explicitly isolates the faulty wheel(s) and accurately estimates the actual torque(s) even with the presence of noise.

In order to improve the braking energy recovery and ensure the braking comfort, a new type of regenerative braking coordinated control algorithm is designed in this paper. The hierarchical control theory is used to the regenerative braking control algorithm. First, the front axle braking force and rear axle braking force are distributed. Then the rear axle motor braking force and mechanical braking force are distributed. Finally, the dynamic coordinated control strategy is designed to control pneumatic braking system and motor braking system. Aimed at keeping the fluctuation of the total braking force of friction and the regenerative braking force small during braking modes switch, a coordinated controller was designed to control the pneumatic braking system to compensate the error of the motor braking force. Based on Matlab/Simulink platform, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established.