Search Results

On urban and emission homologation cycles, engines operate predominantly at low speeds and part loads where engine friction losses represent around 10% of the consumed fuel energy but would account for 25% of the fuel consumption once combustion efficiency is taken into account. Under such mild conditions, engine and engine oil temperatures are also lower than ideal. The influence of oil viscosity on friction losses are significant. By reducing lubricant viscosity, engine friction, fuel consumption and emissions are reduced. Tribological and machine learning models were investigated to predict the effect of oil viscosity on fuel consumption during the FTP75 emission cycle with the use of detailed actual emission test measurements. Oil viscosity was calculated with the measured oil temperature. As the same vehicle transient is followed in the cold and hot phases, the models were evaluated by comparing their prediction of fuel consumption in the hot phase versus the measured value.

The exhaust gases emission regulations, with very restrictive limits, have imposed the need of developments in other areas, among them, in the internal components developments. The necessary maintenance of low levels of oil consumption for long periods of engine use, leads to the development of components with higher wear resistance and higher efficiency. Among these components, the piston rings and the cylinders play an important role in the oil consumption control and also in the engine service life. This paper presents the results of engine tests run to compare the components wear (piston rings and cylinders) when using different types of lubricant oils.

The components of the piston/ring/liner system must have their wear resistance increased to meet the new engine requirements. The engine operating conditions can be even worse if corrosive wear in the engine is expected to occur. This paper presents a study to improve the wear resistance of piston ring coatings and liner materials by the addition of chromium carbide and carbide forming alloying elements, respectively. The engine tests were run with high sulfur fuel (about 1.0 wt%) and lubricant with low total base number (TBN) with the objective of increasing the corrosive conditions. The results show the improvement of the ring coatings wear resistance with the increase of the chromium carbide content. The cylinder liner materials also presented lower wear rates when they had hard particles, mainly due to the addition of niobium, vanadium and titanium.

In the present work, a system approach to the tribological optimization of passenger car engines is demonstrated. Experimental data and simulation results are presented to demonstrate the role of surface specifications, ring pack, and lubricant on the piston/bore tribology. The importance of in-design “pairing” of low-viscosity motor oils with the ring pack and the cylinder bore characteristics in order to achieve maximum reduction in GHG emissions and improvement in fuel economy without sacrificing the endurance is elucidated. Earlier motored friction data for two different gasoline engines - Ford Duratec and Mercedes Benz M133 - using motor oils of different viscosity grades are now rationalized using AVL EXCITE® piston/bore tribology simulations. The main difference between the engines was the cylinder bore surface: honed cast iron vs thermally sprayed, and the valve train type: direct-acting mechanical bucket (DAMB) vs roller finger follower (RFF).

With the current use of bio-renewable fuel, the application of Ethanol in Flex-Fuel vehicles presents a very low CO2 emission alternative when the complete cycle, from plantation, fuel production, till vehicle use, is considered. In Brazil more than 80% of the car production is composed of Flex-Fuel vehicles. Due to the lower heating content of the Ethanol, more aggressive combustion calibrations are used to obtain the same engine power than when burning gasoline. Such Ethanol demands, associated with the continuous increase of engine specific power has lead to thermo-mechanical loads which challenges the tribology of piston rings. The ethanol use brings also some specific tribological differences not very well understood like fuel dilution in the lube oil, especially on cold start, corrosive environment etc. Under specific driving conditions, incipient failures like spalling on nitrided steel top rings have been observed.

Wear of piston ring and cylinder was modelled through a computer code that calculates the hydrodynamic and roughness contact pressures acting on the contact surfaces. Both pressures are fully and coupled solved through, respectively, Reynolds equation and Greenwood-Williamson model. Piston secondary motion and piston groove thermal deformations are considered. The latter was discovered to be fundamental in defining the top ring worn profile. Due to the rough contact pressures, the model predicts material removal from both piston ring and cylinder surfaces and recalculates the system, hence simulating the evolution of the worn sliding surface of both parts. The predicted wear of the piston ring pack and the cylinder wall are compared with a medium duty diesel engine tested for 750 hours in dynamometer.

The present study looks into different possibilities for tribological optimization of the piston/bore system in heavy duty diesel engines. Both component rig tests and numerical simulations are used to understand the roles of surface specifications, ring pack, and lubricant in the piston/bore tribology. Run-in dynamics, friction, wear and combustion chamber sealing are considered. The performance of cylinder liners produced using a conventional plateau honing technology and a novel mechanochemical surface finishing process - ANS Triboconditioning® - is compared and the importance of in-design “pairing” of low-viscosity motor oils with the ring pack and the cylinder bore characteristics in order to achieve maximum improvement in fuel economy without sacrificing the endurance highlighted. A special emphasis is made on studying morphological changes in the cylinder bore surface during the honing, run-in and Triboconditioning® processes.

The piston rings are responsible for maintaining some engine functioning parameters in an acceptable range, mainly the lubricant oil consumption and the blow-by gases flow from the combustion chamber to the crankcase. The wear resistance of these components is related to their capacity of properly exerting these functions during the whole engine life. In Diesel engines, all the rings have a wear resistant coating applied to their contact face with the cylinder wall. However, the chrome plating of the second groove compression ring is a conservative solution with the possibility of the development of lower cost alternatives. This paper presents the results of engine tests that compare the wear resistance of second groove rings with chrome plating and rings made of nitrited gray cast iron. Test results with similar gray cast iron rings are also analyzed to infer the influence of the nitriding treatment on the wear resistance of this material.

The evolution of internal combustion engines has led to friction reduction as well as to gaseous emissions reduction, demanding the use of narrower rings. Nodular cast iron is used satisfactorily for compression piston rings, with wear resistant coatings to improve their durability. However, for more severe applications and rings narrower than 1.2mm, even the nodular cast iron mechanical resistance is not enough. In this way, the use of steel is recommended, which may have its tribological properties improved by the nitriding thermochemical treatment. This paper presents the characteristics of the materials and of the nitriding process of compression and oil control rings as well as bench and dynamometric test results run during the development of these products.

Engine developments have led to higher mechanical and thermal loads on the components, at the same time that lower friction losses are also sought. Therefore, the development of better materials and of surface treatments has received great emphasis. This paper presents the results of dynamometric engine tests with a proposed piston ring pack, composed of a gas nitrided steel top ring, a nitrided gray cast iron second ring and a normal production chrome plated oil ring. The proposed pack showed very low wear when applied to a medium duty diesel engine, besides being a cost-effective alternative to the conventional pack with moly coated and chrome plated (respectively in the top and second) rings. The proposed pack also caused very low wear on the cylinder bore, specially near the TDC, where the bore wear is usually maximum.

The cylinder bore honing quality is an essential factor for a good engine performance and durability. A bad surface finish can result in an excessive lubricant oil consumption, high piston ring wear and scuffing occurrence. In this paper the most important characteristics of bore honing for cast iron cylinders and their influence in the combustion engine performance are described and discussed. Despite its importance, the bore honing is commonly undervalued due to various reasons including the difficulty of a practical but sufficient method of quality qualifying. Some honing commonly misunderstood concepts are detailed and SEM photographs of bore surface from both good and bad finish are presented. At the end of this paper it is also presented a recommendation for a practical evaluation method of honing quality.

The analysis of the wear resistance of engine components must take into account the whole system. It is of no use to improve the properties of one of the components if it will cause higher wear on the other components of the tribological system. This paper presents a study to improve the wear resistance of piston ring coatings and liner materials at the same time that the compatibility between their wear rates is focused. The diesel engine tests were run with high sulfur fuel (about 0.9 wt%) and lubricant with low total base number (TBN) with the objective of increasing the corrosive conditions. The results show that the best compatibility between the wear rates of the top rings and liners is achieved when the rings are coated by plasma spraying with a molybdenum based material containing approximately 15% of moly carbide and when the liners are made of pearlitic gray cast iron with niobium, vanadium and titanium additions.

The higher load in heavy duty Diesel engines and the use of piston ring coatings with higher wear resistance cause more severe working conditions to the cylinder liners. In some cases, high localized wear occurs at the top dead center (TDC) of the first groove ring, where the loads and lubrication conditions are critical. It was studied the effect of the addition of hard particles on cylinder liner materials. The presence of these particles was obtained through the use of small quantities of strong carbide forming alloying elements: Vanadium, Niobium and Titanium. Cylinder liners with hard particle addition were tested in comparison to regular liners. This test used high sulfur fuel (> 1.0 wt %) and low additivation lubricant oil, maintaining the same ring pack configuration for both liners. The results showed sensible liner wear reduction at the TDC of the first ring without compromising the ring pack performance.

Due to several market demands of higher wear and scuffing resistance, Duplex PVD (Physical Vapor Deposition) CrN top ring has been used in Heavy Duty Diesel (HDD) engines. The ring comprises a nitrided high chromium stainless steel with a PVD ceramic CrN coating. For High Speed Diesel (HSD) vehicles with lower demands, MAHLE has developed an alternative PVD coated ring, which balances the cost and performance ratio. This alternative, named High Value PVD (HV-PVD), consists of applying the best resistant coating for wear and scuffing, PVD, onto a less costly ring material, Ductile Cast Iron. The HV-PVD top ring has been tested in HSD engines and shown excellent performance. Additional advantages of the HV-PVD are its lower friction coefficient and better tribological compatibility with the cylinder bore materials when compared to the traditional galvanic chrome based coatings. Such features lead to reduced engine friction and lower cylinder wear.

In lubricating and specialty oil industries, blending is routinely used to convert a finite number of distillation cuts produced by a refinery into a large number of final products matching given specifications regarding viscosity, flash point, pour point or other properties of interest. To find the right component ratio for a blend, empirical or semi-empirical equations linking blend characteristics to those of the individual components are used. Mathematically, the problem of finding the right blend composition boils down to solving a system of equations, often non-linear ones, linking the desired properties of the blend with the properties and percentage of the blend components. This approach can easily be extended to crankcase lubricants, in which case major blend constituents are base oils, additive packages, and viscosity index improvers. Artificial intelligence (AI) tools allow accurate predictions of the basic physicochemical properties of such blends.

Recent developments of diesel engines have aimed the improvement of their durability as well as cost optimizations. Although these tendencies seem to be contradictory, many technologies have been applied with results that are very satisfactory. The development of components, specially the piston rings, has led to solutions with optimized performance of service life as well as of functional characteristics of oil consumption control, blow-by control and friction reduction. The use of nitrided piston ring packs allows the maximization of the system performance without compromising the cylinder bore wear, as the tribological pair is very compatible. This paper presents the results of tests with nitrided first and second groove rings for medium and heavy-duty diesel engines.

The application of multipiece oil control rings (two segments or rails and one expander) to Otto engines is very efficient and has been used for many years. However, development work to improve their performance, durability and manufacturing costs is desirable. The contoured segment is an alternative to reduce the variation of oil ring unit pressure during engine life. This paper shows the results of engine tests with this component, where nitrided segments with regular stainless steel expanders and nitrided expanders were used. The results showed satisfactory behaviour, with low wear between segments and nitrided expanders as well as between segments and the cylinder wall.

The fuel economy and gaseous emissions features have led the engine developments for the last few years. Various actions taken to meet these objectives imposed the necessity of components, in this case oil control rings, with higher mechanical resistance, durability and efficiency during the engine life. A new nodular cast iron alloyed with Niobium was developed. The presence of Niobium carbides raises significantly the wear resistance of this material. New configurations of oil control rings with taper faces or barrel faces showed a better performance if compared with two-piece conventional rings. The contact surface height variation during the engine life (and also the mean specific contact pressure variation in the ring land and cylinder wall contact) brings benefits in the oil consumption reduction without compromising the durability of rings and cylinders.

With the increase of thermal and mechanical loads, some spark ignition (SI) engines may present excessive wear on the piston top groove. The problem was studied first by numerical simulation. Several parameters were found to influence the groove wear. E.g., ring side face roughness and hardness. But the main influence found was the relative attitude between groove flank and ring side face. As the instantaneous attitude varies during the engine cycle, the problem was studied with a commercial ring dynamics computer program and considering thermal and mechanical deformations that occur in the piston during engine operation. The expected groove wear was estimated by the accumulated “wear load” during critical engine operation regimes. Experimental results of engines with groove wear solved by design optimization are shown.

With the worldwide trend towards CO2 emission reduction, renewable fuels such as ethanol are gaining further importance. However, the use of ethanol as a fuel can bring some tribological impacts. Friction and wear of engine parts when lubricants are contaminated with ethanol are not very well understood. Within this scenario, the present paper introduces a new procedure to investigate the ethanol dilution on the performance of engine oils. Friction and wear of actual piston ring and liner were evaluated in a reciprocating test designed to emulate real thermomechanical conditions of both urban and highway car use. In addition to fresh oil, lubricant/ethanol emulsions were prepared carefully following two different procedures - unheated and heated mixing. The former to emulate cold start and “bakery” driving use, the latter to reproduce what happens after the engine heats in normal conditions.