This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
The code applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See J1116 and J1057a.) The loading procedure is limited to standing starts in order to reduce the number of variables that are difficult to control and measure. Because of the difficulties in controlling some of the other variables, meaningful numerical comparison of time and load from scraper to scraper requires that data be taken at the same time and place, and that the units being compared be of approximately equal capacity.
The code applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.) The loading procedure is limited to standing starts in order to reduce the number of variables that are difficult to control and measure. Because of the difficulties in controlling some of the other variables, meaningful numerical comparison of time and load from scraper to scraper requires that data be taken at the same time and place, and that the units being compared be of approximately equal capacity.
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
This standard is intended for cutting edge sections used on: a Tractor-scrapers as described in SAE J1057 and J728. b Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation.
This SAE Standard establishes a test method to measure drag force of self-propelled, as well as towed, construction, forestry, and industrial machines, with or without payload, as listed in SAE J/ISO 6165 and J1116. Drag force is measured as a function of travel speed.
This SAE Standard establishes a test method to measure drag force of self-propelled, as well as towed, construction, forestry, and industrial machines, with or without payload, as listed in SAE J/ISO 6165 and J1116. Drag force is measured as a function of travel speed.
This SAE Standard establishes a test method to measure drag force of self-propelled, as well as towed, construction, forestry, and industrial machines, with or without payload, as listed in SAE J/ISO 6165 and J1116. Drag force is measured as a function of travel speed.
This recommended practice applies only to straight, angling, semi-U, and U-blade dozers for crawler and wheel tractors. It applies to angling blade dozers only in the straight (not angled) position.
This recommended practice applies only to straight, angling, semi-U, and U-blade dozers for crawler and wheel tractors. It applies to angling blade dozers only in the straight (not angled) position.
The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580.
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters.
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.