Refine Your Search

Date

Date

Topic

Topic

AMS B Finishes Processes and Fluids Committee Roll Hydrogen fuel Simulators Vehicle dynamics Drag People and personalities Nickel

Search Results

Viewing 1 to 20 of 117
123Next >Last >>
Sort by title
Standard

Weldability Test for Weld Filler Metal Wire
2011-04-13
HISTORICAL
ARP1876B
This SAE Aerospace Recommended Practice defines a method for determining the weldability of weld filler metal in continuous coil or cut length form. It is applicable to all solid (non flux-containing) wires. It is intended as a referee method for testing weld filler metals in case of dispute between purchaser and vendor.
Standard

Treatment of Sheet Metal Parts Corrosion-Resistant Steel
2017-09-20
CURRENT
AMS2550F
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

Treatment of Sheet Metal Parts Corrosion-Resistant Steel
2014-07-31
HISTORICAL
AMS2550E
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

Training and Approval of Heat-Treating Personnel
2019-06-11
CURRENT
ARP1962B
This SAE Aerospace Recommended Practice (ARP) describes training and approval of personnel performing certain heat-treating and associated operations that could have a material impact on the properties of materials being heat treated. It also recommends that only approved personnel perform or monitor the functions listed in Table 1.
Standard

Training and Approval of Heat-Treating Personnel
2007-05-01
HISTORICAL
ARP1962A
This document requires that the company (facility) employing the personnel ensure a verifiable program of on-the-job training, experience, education, classroom instruction, and evaluation of personnel using either company-created programs or programs described herein.
Standard

The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa
2017-03-21
CURRENT
AMS03_4A
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
Standard

The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa
2015-04-27
HISTORICAL
AMS03_4
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
Standard

TREATMENT OF SHEET METAL PARTS Corrosion-Resistant Steel
1992-04-01
HISTORICAL
AMS2550D
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

TIN PLATING, IMMERSION
1991-10-01
HISTORICAL
AMS2409E
This specification covers the engineering requirements for producing a thin tin coating on aluminum alloys by an immersion process.
Standard

Selective (Brush) Nickel Plating Low-Stressed, Low Hardness Deposit
2000-10-01
CURRENT
AMS2441A
This specification covers the engineering requirements for selective (brush) electrodeposition of nickel and the properties of the deposit. This process has been used typically to provide moderate corrosion and oxidation resistance and dimensional build-up and restoration of parts which may operate in service up to 700 degrees F (371 degrees C), where low tensile stress in the deposit is required to avoid marked reduction of fatigue strength, but usage is not limited to such applications.
Standard

Selective (Brush) Nickel Plating Low-Stressed, Hard Deposit
2000-10-01
CURRENT
AMS2439A
This specification covers the engineering requirements for selective (brush) electrodeposition of nickel and the properties of the deposit. This process has been used typically to provide good wear resistance and dimensional build-up and restoration of parts which may operate in service up to 450 degrees F (232 degrees C), where low tensile stress in the deposit is required, but usage is not limited to such applications. Diffusion heat treatment of the deposit is not required.
Standard

SILVER BRAZING Unhardened Steels and Alloys
1972-11-01
HISTORICAL
AMS2664B
This specification covers the engineering requirements for production of brazed joints in parts made of iron, nickel, and cobalt base alloys by use of silver alloys and the properties of such joints.
Standard

SILVER BRAZING Unhardened Steels and Alloys
1973-12-01
HISTORICAL
AMS2664C
This specification covers the engineering requirements for production of brazed joints in parts made of iron, nickel, and cobalt base alloys by use of silver alloys and the properties of such joints.
123Next >Last >>
X