Search Results

Standard

Rated Operating Load for Loaders Equipped with Log or Material Forks without Vertical Mast

2002-10-31

HISTORICAL

J1197_200210

This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.

Standard

Rated Operating Load for Loaders Equipped with Log or Material Forks Without Vertical Mast

2011-10-27

CURRENT

J1197_201110

This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.

Standard

RATED OPERATING LOAD FOR LOADERS EQUIPPED WITH LOG OR MATERIAL FORKS WITHOUT VERTICAL MAST

1991-02-01

HISTORICAL

J1197_199102

This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.

Standard

Metric Countersunk Holes for Cutting Edges and End Bits

2011-10-27

CURRENT

J1580_201110

this document is to be used on cutting edges and end bits in conjunction with metric bolts (reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are further defined in SAE J63.

Standard

Material Handler Nomenclature and Specifications

2019-04-15

CURRENT

J2506_201904

This SAE Standard establishes terminology and the content of commercial literature specifications for self-propelled crawler and wheeled material handlers, pedestal mounted material handlers and their equipment as defined in 3.1. Illustrations used here are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been provided to describe the principles to be used in applying this document. (Material handlers share many design characteristics with hydraulic excavators and log loaders; primarily 360 degree continuous rotation of the upperstructure relative to the undercarriage or mounting. They differ in their operating application. Material handlers are used for the handling of scrap material and normally utilize grapples or magnets. Hydraulic excavators are used for the excavation of earth, gravel and other loose material utilizing a bucket.

Standard

METRIC COUNTERSUNK HOLES FOR CUTTING EDGES AND END BITS

1989-12-01

HISTORICAL

J1580_198912

this document is to be used on cutting edges and end bits in conjunction with metric bolts (reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are further defined in SAE J63.

Standard

HOLE PLACEMENT ON DOZER END BITS

1980-02-01

HISTORICAL

J63_198002

The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057aup to a maximum weight of 100,000 lb (45,000 kg).

Standard

Earthmoving Machines—Method for Locating the Center of Gravity

1993-09-01

J874_199309

This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.

Standard

Cutting Edge—Optional Cross-Sections and Dimensions Loader Straight

2006-02-05

HISTORICAL

J1581_200602

The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.

Standard

Cutting Edge—Double Bevel Cross Sections

2008-07-07

HISTORICAL

J738_200807

This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a Tractor - Scrapers as defined in SAE J728. b Dozers as described in SAE J729 and J173. c Loaders as described in SAE J731. d Graders as described in SAE J870. Hole spacing is defined for dozers and scrapers in J737 and graders in J739. Hole conformation is defined in J740.

Standard

Cutting Edge—Cross Sections Loader Straight with Bolt Holes

2006-02-05

HISTORICAL

J1304_200602

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters.

Standard

Cutting Edge—Cross Sections Loader Straight

2006-02-05

HISTORICAL

J1303_200602

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.

Standard

Cutting Edge - Optional Cross-Sections and Dimensions Loader Straight

2011-10-25

CURRENT

J1581_201110

The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.

Standard

Cutting Edge - Double Bevel Cross Sections

2014-01-08

HISTORICAL

J738_201401

This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.

Standard

Cutting Edge - Double Bevel Cross Sections

2020-01-15

CURRENT

J738_202001

This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.

Standard

Cutting Edge - Cross Sections Loader Straight with Bolt Holes

2011-10-25

CURRENT

J1304_201110

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.

Standard

Cutting Edge - Cross Sections Loader Straight

2011-10-25

CURRENT

J1303_201110

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85. NOTE—For some heavy duty applications, cross sections with larger blunts and greater bevel angles may be required.

Standard

Countersunk Square Holes for Cutting Edges and End Bits

2011-10-25

CURRENT

J740_201110

To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).

Standard

Countersunk Square Holes for Cutting Edges and End Bits

2006-02-05

HISTORICAL

J740_200602

To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).

Standard

CUTTING EDGE—OPTIONAL CROSS-SECTIONS AND DIMENSIONS LOADER STRAIGHT

1989-09-01

HISTORICAL

J1581_198909

The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.