Search Results

Standard

Tension Indicating Washer Tightening Method for Fasteners

1999-05-01

HISTORICAL

J2486_199905

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.

Standard

THREAD ROLLING SCREWS

1972-07-01

HISTORICAL

J81_197207

This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that “thread rolling” screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

THREAD ROLLING SCREWS

1979-06-01

HISTORICAL

J81_197906

This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

Surface Discontinuities on Nuts

2017-01-04

CURRENT

J122_201701

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.

Standard

STEEL SELF-DRILLING TAPPING SCREWS

1979-06-01

HISTORICAL

J78_197906

This standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this standard to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. An Appendix is included to provide a recommended technique for measuring the case depth on the screws.

Standard

STEEL SELF-DRILLING TAPPING SCREWS

1973-10-01

HISTORICAL

J78B_197310

This standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this standard to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. An Appendix is included to provide a recommended technique for measuring the case depth on the screws.

Standard

STEEL SELF-DRILLING TAPPING SCREWS

1972-07-01

HISTORICAL

J78_197207

This standard covers the dimensional and general specifications, including performance requirements, for steel self-drilling tapping screws suitable for use in general applications. It is the objective of this standard to insure that self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly or service. An Appendix is included to provide a recommended technique for measuring the case depth on the screws.

Standard

Push-On Spring Nuts Metric Series - General Specifications

2013-04-16

HISTORICAL

J892M_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Standard

Push-On Spring Nuts Metric Series - General Specifications

2016-11-21

CURRENT

J892M_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Standard

Push-On Spring Nuts Inch Series - General Specifications

2016-11-23

CURRENT

J892_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.

Standard

Push-On Spring Nuts Inch Series - General Specifications

2013-04-16

HISTORICAL

J892_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.

Standard

Nut and Conical Spring Washer Assemblies

2017-05-30

CURRENT

J238_201705

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Standard

Mechanical and Material Requirements for Steel Nuts

2021-02-08

WIP

J995

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”

Standard

Mechanical and Material Requirements for Steel Nuts

1999-07-01

HISTORICAL

J995_199907

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of ASME B18.2.2 or ASME B18.6.3, as applicable.

Standard

Mechanical and Material Requirements for Steel Nuts

2012-02-21

HISTORICAL

J995_201202

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 in, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”

Standard

Mechanical and Material Requirements for Steel Nuts

2017-07-20

CURRENT

J995_201707

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”

Standard

Mechanical and Chemical Requirements for Nonthreaded Fasteners Carbon Steel Solid Rivets—Inch Series

2007-07-11

HISTORICAL

J430_200707

These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.

Standard

Mechanical and Chemical Requirements for Nonthreaded Fasteners Carbon Steel Solid Rivets - Inch Series

2016-11-21

CURRENT

J430_201611

These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.

Standard

Mechanical and Chemical Requirements for Nonthreaded Fasteners Carbon Steel Solid Rivets - Inch Series

2013-04-15

HISTORICAL

J430_201304

These specifications cover the mechanical and chemical requirements, and surface discontinuities limits for carbon steel solid rivets used in automotive and other related industries.

Standard

MECHANICAL AND QUALITY REQUIREMENTS FOR TAPPING SCREWS

1979-06-01

HISTORICAL

J933_197906

This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in SAE J478.)