Search Results

Edge flanging represents one of the forming modes employed in multistage forming, and advanced high strength steels (AHSS) are more prone to edge cracking during sheared edge flanging than the conventional high strength steels (HSS) and mild steels. The performance of the sheared edge in flanging operation depends on the remaining ductility of the material in the sheared edge after the work hardening (WH) and damage produced by blanking and subsequent forming operations. Therefore, it is important to analyze the effect of work hardening produced by blanking and subsequent forming operations prior to edge flanging on the edge flanging performance. In this study, the effect of different forming operation sequences prior to edge flanging on the edge flanging performance was analyzed for a dual phase 780 steel.

The formability window of a material depends upon the forming limit and its strain distribution ability. For two materials with the same forming limit, the formability performance is governed by their strain distribution ability. In this study, strain hardening behavior of different strength steels was investigated using a uniaxial tension test and the forming limit was studied using both Marciniak cup and dome tests. The n-value of steels varies with strain. Different strain hardening behaviors are found between mild steels and high strength steels. Strain distribution ability of steels increases with the increase in the overall n-value. The peak n-value at a low strain level enhances the strain distribution ability of the steel. It has been shown from both theoretical and experimental studies that a constant thickness strain line exists on the left side of the forming limit curve.

Material constitutive modeling is an important aspect in the continuous improvement process for sheet metal forming simulation and analysis. In this study, a sensitivity study of material constitutive parameters on forming simulation results is carried out for two different sheet metal parts. Three different yield criteria are evaluated in the simulation including isotropic yield criterion, Hill's 1948 anisotropic yield criterion and Barlat's non-quadratic anisotropic yield criterion. It is found that the forming results depend upon the yield criterion used in the simulation. Both thinning and stress in the formed part are very sensitive to the change in anisotropy value (r-value). Effects of strain rate sensitivity of a material on forming results are demostrated through the use of two different stress and strain data from different tensile speeds. It is also found that forming results such as thinning are very sensitive to the strain hardening behavior of the material.

In previous investigations, it has been shown that the dent resistance of an auto body panel depends upon the yield strength of the material. However, it is known that the yield strength of steel increases with prestrain due to strain hardening. Panel design and material selection based on the material properties obtained from unstrained sheet steels may lead to inaccurate prediction of the dent resistance of the formed panel. In this study, the effect of prestrain on the static dent resistance of auto body panels was investigated. Using existing empirical relationships between dent resistance and panel properties, it was found that the static dent resistance of an auto panel depends not only on the part geometry and material properties but also on the strain level in the panel. The improvement in dent resistance resulting from a material change from an AKDQ steel to a bake hardenable steel or a high strength steel was determined at different strain levels.

The front rail plays a very important role in vehicle crash. Trigger holes are commonly used to control frame crush mode due to their simple manufacturing process and flexibility for late changes in the product development phase. Therefore, a study, including CAE and testing, was conducted on a production front rail to understand the effects of trigger hole shape, size and orientation. The trigger hole location in the front rail also affects crash performance. Therefore, the effect of trigger hole location on front rail crash behavior was studied, and understanding these effects is the main objective of this study. A tapered front rail produced from 1.7 mm thick DP600 steel was used for the trigger hole location investigation. Front rails with different trigger spacing and sizes were tested using VIA sled test facility and the crash progress was simulated using a commercial code RADIOSS. The strain rate, welding and forming effects were incorporated in the front rail modeling.

This paper introduces an industrial application of digital image correlation technique on the measurement of aluminum edge stretching limit. In this study, notch-shape aluminum coupons with three different pre-strain conditions are tested. The edge stretching is proceeded by standard MTS machine. A dual-camera 3D Digital Image Correlation (DIC) system is used for the full field measurement of strain distribution in the thickness direction. Selected air brush is utilized to form a random distributed speckle pattern on the edge of sheet metal. A pair of special optical lens systems are used to observe the small measurement edge area. From the test results, it demonstrate that refer to the notched coupon thickness, pre-tension does not affect the fracture limit; refer to the virgin sheet thickness, the average edge stretch thinning limits show a consistent increasing trend as the pre-stretch strain increased.

Advanced High Strength Steels (AHSS) have been implemented in the automotive industry to balance the requirements for vehicle crash safety, emissions, and fuel economy. With lower ductility compared to conventional steels, the fracture behavior of AHSS components has to be considered in vehicle crash simulations to achieve a reliable crashworthiness prediction. Without considering the fracture behavior, component fracture cannot be predicted and subsequently the crash energy absorbed by the fractured component can be over-estimated. In full vehicle simulations, failure to predict component fracture sometimes leads to less predicted intrusion. In this paper, the feasibility of using computer simulations in predicting fracture during crash deformation is studied.

Body panel performance properties such as denting force, oil canning/critical buckling load, initial and secondary stiffnesses under dynamic loading (drop weight test) were measured for different strength steels and two aluminum alloys using both flat and curved sheets. It was found that all these properties varied with the drop velocity. For the steels, the denting force steadily increased with the increase in drop velocity. For the aluminum alloys, the denting force increased with the drop velocity at lower velocities and decreased or remained unchanged at higher velocities. The oil canning/critical buckling load increased with the increase in drop velocity and initial and secondary stiffnesses decreased with the increase in drop velocity for both steel and aluminum. The dent resistance performance for some aluminum alloys with thicker gauge is comparable to steels dent tested at lower velocities.

The dent resistance of an automotive body panel has been used as one of key design parameters for automotive body panels. Quasi-static dent testing procedures have been well documented in North America using A/SP Standard Dent Resistance Test Procedures and numerous publications in static denting are also available. However, test procedures under dynamic denting are not very well documented and limited data exist on dynamic denting performance of automotive body panels. In this paper, dynamic dent tests are carried out using different impact velocities and different test procedures. The advantages and disadvantages of test procedures are discussed. Different ways to characterize the dynamic dent test results are investigated and discussed. Due to higher impact velocity during the dynamic dent testing, the acceleration effect must be considered in the data analysis. Experiments were carried out on a hydraulic controlled dynamic dent tester.

Customer preference for the “eye catching” and aesthetically good looking product has made the car quality a key competitive issue. Manufacturers have no choice but to design and manufacture products to exceptional levels of quality while remaining cost competitive. If excessive costs of “quality” are to be avoided, product and process design standards must be harmonised to ensure that product quality can be designed in from the start of a new product development cycle. However, the subjective nature of the car body aesthetic quality makes it difficult to ensure effective communication across different functions of the organization. Traditionally, product engineers are more used to designing for product performance targets such as stiffness, dentability and weight, while process engineers are primarily concerned with ensuring manufacturing feasibility within an agreed cost target.

Interface friction between sheet metal and tooling in sheet metal forming is examined in different forming modes using laboratory simulative tests. Stretchability is studied by the limiting dome height test; drawability is investigated by a four inch Swift cup draw test and the coefficient of friction is measured by the draw bead simulator under bending and unbending deformation. The responses of the interface friction in six different coated and uncoated steel sheets are studied using seven different lubricants. It is found that the interface friction between sheet metal and tooling is very sensitive to the forming mode and the type of coating. For the same lubricant and coated material, two different forming modes may produce very different results in interface friction. However, overall good and bad lubricants for all forming modes can be determined for a given coated material using these three tests.