Search Results

This SAE Recommended Practice is applicable to pneumatic Passenger Car “P” Type, Light Truck Metric, and Light Truck High Flotation tires, or similar tires approved by bodies other than Tire & Rim Association. The methodology is applicable within normal operating ranges of vertical load and inflation pressure, and for velocities between 115 km/h and 15 km/h (71 mph and 9 mph) during a relatively short duration event such as a coastdown. This procedure is applicable only to operation in the free-rolling mode at zero slip and camber angle for ambient temperatures between 20 °C and 28 °C (68 °F and 82 °F) and for surfaces with diameters of 1.2 m (48 in) diameter or greater. Details regarding the equipment, tires, and test methods used specifically for validation of this document are included in Appendix A. Two basic measurement methods covered by this document are as follows:

This SAE Recommended Practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car, light truck, and highway truck and bus tires. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This SAE Recommended Practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car, light truck, and highway truck and bus tires. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This SAE Recommended Practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car, light truck, and highway truck and bus tires. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This SAE Recommended Practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car, light truck, and highway truck and bus tires. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This SAE Recommended Practice describes the determination of tire pull force properties for an uninclined tire (SAE J670e) on a laboratory flat surface tire force and moment machine. It is suitable for accurately determining pull forces and residual aligning moments for passenger and light-truck tires. These properties are important determinants of vehicle trim (See section 2.1.2). They describe steady-state, free-rolling pull effects ascribable to tires. The test method described in this document is suitable for comparative evaluation of tires for research and development purposes. The method is also suitable for modeling when followed carefully.

This recommended practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car, light truck, and highway truck and bus tires. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This recommended practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car tires designed primarily for normal highway service. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This Recommended Practice applies to the laboratory measurement of rolling resistance of pneumatic passenger car and light truck tires. The procedure applies only to the steady-state operation of free-rolling tires at zero slip and inclination angles; it includes the following three basic methods:

This SAE Recommended Practice describes the determination of tire pull force properties for an uninclined tire (SAE J670e) on a laboratory flat surface tire force and moment machine. It is suitable for accurately determining pull forces and residual aligning moments for passenger and light-truck tires. These properties are important determinants of vehicle trim (See section 2.1.2). They describe steady-state, free-rolling pull effects ascribable to tires. The test method described in this document is suitable for comparative evaluation of tires for research and development purposes. The method is also suitable for modeling when followed carefully.

This Recommended Practice describes some basic design requirements and operational procedures associated with equipment for laboratory measurement of tire force and moment properties of the full range of passenger car tires. These properties must be known to establish the tire's contribution to vehicle dynamic performance. Many factors influence laboratory tire force and moment measurements. This Recommended Practice was compiled as a guide for equipment design and test operation so that data from different laboratories can be directly compared and applied to vehicle design and tire selection problems. It is recognized that laboratory measurements define performance in a controlled and idealized situation that may not correspond to conditions encountered in a vehicle's operating environment. Several decades of testing experience in different laboratories indicates, however, that these tests can provide a very useful bench mark for evaluation of tire performance.

This Information Report presents background and rationale for SAE Recommended Practice J1106, Laboratory Testing Machine and Procedures for Measuring the Steady Force and Moment Properties of Passenger Car Tires. The purpose of SAE J1106 is to define standards for equipment design and test procedures so that data from different laboratories can be directly compared. Whereas such standardization is not a requirement for testing associated with tire development, it is necessary in the context of vehicle design and tire selection problems. The basic approach employed in developing SAE J1106 was to consolidate and document existing technology as embodied in equipment and procedures currently employed for routine tire evaluations. Equipment and procedures whose current use is restricted to research applications were not considered. Research experience is discussed in this Information Report, however, to the extent deemed necessary to provide background and rationale for SAE J1106.

This SAE Recommended Practice provides a method for testing the speed performance of passenger car tires under controlled conditions in the laboratory on a test wheel. This procedure applies to “standard load,” “extra load,” and “T-type high-pressure temporary-use spare” passenger tires.

This SAE Recommended Practice provides a method for testing the speed performance of passenger car tires under controlled conditions in the laboratory on a test wheel. This procedure applies to “standard load,” “extra load,” and “T-type high-pressure temporary-use spare” passenger tires.

This SAE Recommended Practice provides a method for testing the speed performance of light truck tires under controlled conditions in the laboratory on a test wheel.

This SAE Recommended Practice provides a method for testing the speed performance of light truck tires under controlled conditions in the laboratory on a test wheel.

This Information Report presents background and rationale for SAE Recommended Practice J1106, Laboratory Testing Machine and Procedures for Measuring the Steady Force and Moment Properties of Passenger Car Tires. The purpose of SAE J1106 is to define standards for equipment design and test procedures so that data from different laboratories can be directly compared. Whereas such standardization is not a requirement for testing associated with tire development, it is necessary in the context of vehicle design and tire selection problems. The basic approach employed in developing SAE J1106 was to consolidate and document existing technology as embodied in equipment and procedures currently employed for routine tire evaluations. Equipment and procedures whose current use is restricted to research applications were not considered. Research experience is discussed in this Information Report, however, to the extent deemed necessary to provide background and rationale for SAE J1106.

This procedure provides a method for testing the speed performance of passenger car tires under controlled conditions in the laboratory on a test wheel. (This procedure does not apply to extra load tires or 'T'-type temporary use spare tires.)

This SAE Recommended Practice describes the determination of passenger car and light truck tire force and moment properties on a belt-type flat surface test machine. It is suitable for accurately determining five tire forces and moments in steady-state under free-rolling conditions as a function of slip angle and normal force which are incrementally changed in a given sequence.

This SAE Recommended Practice describes the determination of passenger car and light truck tire force and moment properties on a belt-type flat surface test machine. It is suitable for accurately determining five tire forces and moments in steady-state under free-rolling conditions as a function of slip angle and normal force which are incrementally changed in a given sequence.